Author: ApplianceFixGuide Team

Problem: Shifter actuator fault

How to Fix F7E5 Error

1. Unplug the washer and tilt it back to access the bottom components.
2. Locate the Shift Actuator (small black box near the Splutch/Motor).
3. Remove the two mounting screws (usually green ground wire attached) and disconnect the harness.
4. Inspect the Splutch arm for freedom of movement.
5. Install the new Shift Actuator, ensuring the pin aligns with the Splutch arm, and screw it in place.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Motor/drive fault (variant)

How to Fix F7E7 Error

1. Unplug the washer and lean it back to access the drive system.
2. Check that the basket spins freely by hand (if stuck, check for obstructions between tubs).
3. Inspect the capacitor and motor wiring harness.
4. Remove the pulley cover and inspect the Splutch Cam assembly for broken teeth/wear.
5. Replace the Splutch Cam kit if worn; if the Splutch is good, replace the Capacitor.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Low water flow; washer not detecting incoming water

How to Fix F8E1 Error

1. Turn off water faucets and unplug the washer.
2. Disconnect the inlet hoses and check the filter screens inside the valve for sediment buildup (clean if clogged).
3. If screens are clean, remove the washer’s top/rear panel to access the valve assembly.
4. Disconnect the wire harness and remove mounting screws.
5. Install the new water inlet valve, reconnect the harness, and reattach the hoses firmly.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Dispenser system problem

How to Fix F8E2 Error

1. Unplug the washer and turn off water.
2. Remove the top panel to access the dispenser assembly.
3. Locate the dispenser motor/diverter on top of the dispenser housing.
4. Disconnect the small wire harness and remove the screws holding the motor.
5. Install the new dispenser motor, ensuring the arm/cam is positioned correctly to direct water flow.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Water hazard; water in tub with lid open too long

How to Fix F8E6 Error

1. This code indicates a ‘Water Hazard’ where water remains in the tub with the lid open for >10 minutes.
2. Close the lid immediately to allow the washer to drain or continue the cycle.
3. If the washer does not drain, press ‘Power/Cancel’ to force a drain cycle.
4. Ensure the drain hose is not kinked or clogged.

Browse all Maytag error codes: Maytag Error Codes

Problem: Wrong voltage; under/over voltage detected

How to Fix F9E9 Error

1. Unplug the washer.
2. Check the wall outlet with another appliance (like a lamp) to ensure it has consistent power.
3. Verify that the outlet voltage is within range (120V +/- 10%) using a multimeter if available.
4. Avoid using extension cords or surge protectors; plug directly into the wall.
5. Plug the washer back in after 1 minute to reset the control board.

Browse all Maytag error codes: Maytag Error Codes

Problem: Door/lid lock opening error

How to Fix dLO Error

1. Unplug the washer and tape the lid or door shut.
2. Access the lock assembly: For Top Loaders, remove the rear screws and slide the top panel forward/up. For Front Loaders, remove the wire band from the door boot seal and peel the seal back.
3. Remove the mounting screws holding the lock in place and disconnect the wire harness.
4. Connect the new lock, secure it with screws, and reassemble the cabinet or door seal.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes

Problem: Washer not draining properly

How to Fix drn Error

1. Unplug the washer and secure the drain hose. Have a bucket or towels ready.
2. Access the pump: For Top Loaders, tape the lid and lean the washer back against a wall. For Front Loaders, remove the lower front access panel (or rear panel depending on model).
3. Clamp the inlet/outlet hoses to prevent spilling, then disconnect them from the old pump.
4. Remove the mounting screws/clips, swap in the new pump, and reconnect hoses securely.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Maytag error codes: Maytag Error Codes