Category: Electrolux

Error Code: H OR HI Difficulty: Easy

Problem: High temperature alert. The temperature inside the refrigerator or freezer is too high.

How to Fix H OR HI Error (Step-by-Step)

1. Do not adjust the temperature settings immediately. This alert means the internal temperature is too high. First, check for simple causes.
2. Ensure both the refrigerator and freezer doors are fully closed. Check if any food items are blocking the door from sealing properly.
3. Inspect the rubber door gaskets (seals) for any tears, dirt, or gaps. Clean the gaskets with warm, soapy water and a cloth to ensure a tight seal.
4. Avoid opening the doors frequently, as this lets warm air inside. Allow the refrigerator several hours to cool down, especially after loading a large amount of groceries.
5. Check that the air vents inside the refrigerator and freezer are not blocked by food packages. Proper air circulation is critical for cooling.
6. If the alert appeared after a power outage, it is normal. The refrigerator needs time to return to its set temperature. The alert should clear on its own.
7. If the alert persists for more than 6-8 hours after checking all these steps, you may need to contact a service.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F8 Difficulty: Hard

Problem: Defrost error.

How to Fix F8 Error (Step-by-Step)

1. Unplug the refrigerator from its power source for safety and confirm the error stays cleared during a full test cycle.
2. A defrost error means the appliance is not properly melting the frost that naturally builds up on the cooling coils.
3. Open the freezer and look for excessive frost buildup on the back interior wall. A heavy layer of ice is a key symptom.
4. Ensure that air vents in the freezer and fresh food compartments are not blocked by food items, as this can disrupt airflow and contribute to frost issues.
5. The problem is typically caused by a failed defrost heater, defrost thermostat, or main control board.
6. These components are located behind the freezer’s interior back panel. Accessing them requires removing shelves and panels.
7. Testing and replacing defrost system components involves working with electrical parts and requires a multimeter. This repair should be handled by a professional service to ensure it’s done correctly and safely.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F7 Difficulty: Hard

Problem: Power connection error.

How to Fix F7 Error (Step-by-Step)

1. Begin with the simplest check: ensure the refrigerator’s power cord is firmly pushed into the wall outlet.
2. Confirm the outlet is working by plugging in another small appliance, like a phone charger.
3. If the outlet is dead, go to your home’s electrical panel and reset the corresponding circuit breaker. If it trips again, you may have an electrical issue requiring an electrician.
4. Carefully inspect the entire length of the power cord for any damage. If you find any, the cord must be replaced.
5. This error often points to a problem with the main electronic control board, which manages power distribution.
6. For safety, unplug the refrigerator before attempting any visual inspection of the internal components located on the rear of the unit.
7. Given the number of potential electrical parts that could cause this error, it is safest and most effective to have a qualified service perform advanced checks.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F6 Difficulty: Hard

Problem: Power connection error.

How to Fix F6 Error (Step-by-Step)

1. First, verify the refrigerator is receiving power. Check that the power cord is plugged in securely to the wall outlet.
2. Test the outlet itself by plugging in a small lamp or other device you know is working.
3. If the outlet has no power, check your home’s circuit breaker panel for a tripped breaker or a blown fuse.
4. Examine the refrigerator’s power cord for any visible signs of damage, such as cuts or frayed wires. Do not use a damaged cord.
5. This error indicates a potential failure in the main power board or related wiring. These components are located behind an access panel on the back of the refrigerator.
6. After unplugging the unit, you can remove the access panel and visually inspect for any burnt marks or loose wire harnesses on the control board.
7. Due to the complexity and number of potential parts involved, any further diagnosis, including testing and replacing internal components, should be performed by a professional appliance service.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F5 Difficulty: Hard

Problem: Temperature error, likely from a defective temperature sensor.

How to Fix F5 Error (Step-by-Step)

1. Turn off power to the refrigerator at the circuit breaker or by unplugging it.
2. Begin by locating the sensor in the fresh food section. It is often housed in a small plastic casing near an air duct. Check for a secure wire connection.
3. Next, inspect the freezer sensor. This requires emptying the freezer and removing the rear interior panel to access the evaporator coil area where the sensor is located.
4. Look for any obvious signs of damage to the sensor or its wires. Ensure the plug is firmly seated.
5. A definitive diagnosis to determine which sensor is faulty requires testing with a multimeter, which is a task for a qualified service.
6. If the connections appear secure, the issue likely requires professional service to test and replace the correct component.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F4 Difficulty: Hard

Problem: Temperature error, indicating a defective temperature sensor.

How to Fix F4 Error (Step-by-Step)

1. Disconnect the refrigerator from power to prevent electrical shock and confirm the error stays cleared during a full test cycle.
2. This error points to a temperature sensor. There are two common sensors: one in the fresh food section (Part #240597203) and one in the freezer (Part #297018400).
3. First, check the fresh food sensor, which is usually visible near a light or air vent. Inspect its wiring for loose connections or damage.
4. To check the freezer sensor, you will need to remove the contents, shelves, and the interior back panel of the freezer.
5. Once accessed, visually inspect the freezer sensor and its wiring for any breaks, corrosion, or loose plugs.
6. Because diagnosing which sensor has failed requires a multimeter and technical knowledge, this is considered a professional repair.
7. If you’ve checked the connections and the error remains, schedule a service call with a certified service for proper diagnosis and part replacement.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F3 Difficulty: Hard

Problem: Temperature error, likely a defective temperature sensor.

How to Fix F3 Error (Step-by-Step)

1. Safely disconnect the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
2. The temperature sensor (thermistor) is typically located inside the freezer, behind the back panel, clipped to the evaporator coils.
3. You will need to remove the shelves and the back panel inside the freezer to access the sensor.
4. Visually inspect the sensor and its wiring for any signs of damage, corrosion, or a loose connection.
5. Reconnect any loose plugs securely. If the wiring is damaged, the sensor assembly will need to be replaced.
6. Testing the sensor’s resistance requires a multimeter and knowledge of the correct specifications, which is best left to a professional.
7. If no visible issues are found, the sensor (Part #5303918214) has likely failed and requires replacement by a service service.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F2 Difficulty: Hard

Problem: Thermostat error.

How to Fix F2 Error (Step-by-Step)

1. Unplug the refrigerator from the wall outlet to ensure safety.
2. Locate the thermostat inside the fresh food compartment. It’s usually a small dial or control box with a temperature probe attached.
3. Check the wiring connected to the thermostat. Look for any loose, disconnected, or visibly damaged wires.
4. Gently reconnect any loose wires. If wires appear frayed or broken, this is likely the source of the error.
5. Since this is a professional-level repair, testing and replacing the thermostat (Part #240597203) requires specialized tools.
6. If the error persists after checking the wiring, it is recommended to contact a qualified appliance service to diagnose and replace the faulty thermostat.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: F1 Difficulty: Moderate

Problem: Thermostat error.

How to Fix F1 Error (Step-by-Step)

1. Disconnect the refrigerator from its power supply before beginning the repair.
2. Locate the thermostat, which is also the temperature sensor (thermistor), typically found inside the refrigerator compartment behind a control panel or near the evaporator coils.
3. Unplug the wire connector attached to the thermostat and confirm the error stays cleared during a full test cycle.
4. Remove any screws or clips holding the old thermostat in place and carefully remove it.
5. Mount the new thermostat (part 240597203) in the same position.
6. Reconnect the wire harness to the new thermostat and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes

Error Code: ER T1 – ER T6 Difficulty: Moderate

Problem: Temperature sensor error.

How to Fix ER T1 – ER T6 Error (Step-by-Step)

1. Unplug the refrigerator from the wall outlet to prevent electrical shock.
2. Locate the temperature sensor (thermistor) inside the fresh food or freezer compartment. It is usually found clipped to the evaporator coils or housed in a small plastic casing on the wall.
3. Disconnect the wire harness from the faulty sensor and confirm the error stays cleared during a full test cycle.
4. If the sensor is attached with a screw, remove it. Otherwise, gently unclip it from its mounting position.
5. Install the new temperature sensor (part 240597203) by connecting the wire harness and securing it in the same location as the old one.
6. Ensure the sensor is positioned correctly for accurate temperature readings.
7. Plug the refrigerator back in. The control board should now receive the correct temperature information, clearing the error code.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes