Category: Electrolux

How to Fix Electrolux Dishwasher Error I50
Error Code: I50 Difficulty: Hard

Problem: There is a problem with the wash motor or the circulation pump. This could be due to a short circuit of the triac or the circulation pump itself.

How to Fix I50 Error (Step-by-Step)
1. Disconnect the dishwasher from power by turning off the circuit breaker and shut off the water supply.
2. Carefully pull the dishwasher out from under the cabinet and lay it on its back to access the motor and pump assembly.
3. Locate the wash motor and circulation pump. Disconnect the wiring harnesses and hoses attached to the assembly. It’s helpful to label them or take a photo beforehand.
4. Unbolt and remove the old motor and pump assembly from the dishwasher sump.
5. Install the new motor and pump assembly, ensuring all mounting bolts are tightened securely. Reconnect all hoses and wiring harnesses.
6. Set the dishwasher upright, slide it back into place, and reconnect the power and water.
7. Run a test wash cycle to check for proper operation and any leaks.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 807473201
- A00223923
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I51
Error Code: I51 Difficulty: Hard

Problem: AC wash pump motor problem.

How to Fix I51 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the main circuit breaker and close the hot water supply valve.
2. You will need to uninstall the dishwasher and lay it on its back to get to the wash motor.
3. The wash motor is a large component at the base of the dishwasher. Disconnect the electrical connectors leading to it.
4. Disconnect the hoses from the motor and pump assembly. Be prepared with towels to catch any remaining water.
5. Remove the screws or clamps that hold the motor assembly in place and lift it out.
6. Place the new motor in the same position and secure it. Reattach the hoses and electrical connectors.
7. Reinstall the dishwasher, restore power and water, and run a cycle to test the new motor.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 807473201
- A00223923
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I52
Error Code: I52 Difficulty: Hard

Problem: Wash pump motor issue.

How to Fix I52 Error (Step-by-Step)
1. Start by ensuring the dishwasher is completely disconnected from both power and water sources.
2. Gently pull the dishwasher out from its bay and tilt it to access the underside components.
3. Identify the wash pump motor. It will be connected to the sump and have several hoses and wires attached.
4. Carefully disconnect all electrical and hose connections from the motor. Note their positions for reassembly.
5. Unfasten the motor from its mounting points and remove it from the dishwasher.
6. Mount the new wash pump motor, and re-establish all the hose and electrical connections.
7. Carefully place the dishwasher back, turn on the utilities, and perform a test run.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 807473201
- A00223923
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I53
Error Code: I53 Difficulty: Hard

Problem: Wash pump motor issue.

How to Fix I53 Error (Step-by-Step)
1. Cut power to the dishwasher via the circuit breaker and turn off the water supply line.
2. Slide the dishwasher out and lay it on its back on a protective blanket to access the motor.
3. The wash pump motor is located at the bottom of the unit. Disconnect the wire harnesses connected to it.
4. Use pliers to release the clamps on the hoses connected to the motor and slide them off.
5. Remove the fasteners securing the motor to the dishwasher frame and take out the old motor.
6. Position the new motor and secure it with the fasteners. Reconnect the hoses and wire harnesses.
7. Set the dishwasher upright, slide it back in, restore power and water, and check its function with a full cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 807473201
- A00223923
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I54
Error Code: I54 Difficulty: Easy

Problem: Wash pump motor issue.

How to Fix I54 Error (Step-by-Step)
1. Press the ‘Cancel’ button to end the current wash cycle.
2. For a full reset, turn off the dishwasher at your home’s circuit breaker for 5 minutes.
3. While power is off, open the dishwasher and remove the bottom dish rack.
4. Inspect the sump area at the bottom for any food debris or foreign objects that could be jamming the wash pump.
5. Carefully remove any obstructions you find and confirm the error stays cleared during a full test cycle.
6. Replace the dish rack, restore power at the circuit breaker, and start a new cycle to check if the error is cleared.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Electrolux dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.
  
  Search Amazon for Electrolux dishwasher drain pump
- Electrolux dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill or low-water symptoms after supply and float checks.
  
  Search Amazon for Electrolux dishwasher water inlet valve
- Electrolux dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating control faults after latch, wiring, and power checks.
  
  Search Amazon for Electrolux dishwasher control board
Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 4, 2026
How to Fix Electrolux Dishwasher Error I55
Error Code: I55 Difficulty: Hard

Problem: DCLink low voltage.

How to Fix I55 Error (Step-by-Step)
1. Disconnect the dishwasher from all power by switching off the corresponding circuit breaker.
2. Remove the lower front access panel (kickplate) to get to the main control board.
3. Visually inspect all wire harnesses and connections to the control board for any signs of loose wires, corrosion, or burn marks.
4. If any connections are loose, reseat them firmly. If wires appear damaged, they may need professional repair.
5. If wiring is secure, replace the main control board (Part #154750503, #154807601, or #154663004) by carefully disconnecting all wire harnesses, removing the mounting screws, and installing the new board.
6. Reconnect all wiring, reattach the kickplate, restore power, and run a test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154750503
- 154807601
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 3, 2026
How to Fix Electrolux Dishwasher Error I56
Error Code: I56 Difficulty: Hard

Problem: DCLink overvoltage.

How to Fix I56 Error (Step-by-Step)
1. Turn off the dishwasher’s power supply at the circuit breaker to prevent electrical shock.
2. Remove the kickplate at the bottom of the dishwasher to access the electronic components.
3. Carefully examine the wiring connected to the main control board. Look for any loose plugs, frayed wires, or signs of heat damage.
4. Ensure all connectors are securely plugged into the control board.
5. An overvoltage error typically points to a critical fault within the main control board.
6. The most reliable solution is to replace the control board (Part #154750503, #154807601, or #154663004).
7. After installing the new board and reconnecting all wires, reassemble the access panel and restore power to test the dishwasher.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154750503
- 154807601
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 3, 2026
How to Fix Electrolux Dishwasher Error I57
Error Code: I57 Difficulty: Moderate

Problem: Wash pump motor issue.

How to Fix I57 Error (Step-by-Step)
1. Shut off both the power and the water supply to the dishwasher.
2. You will need to slide the dishwasher out from under the counter. Place towels down to catch any spilled water.
3. Disconnect the water inlet line, the drain hose, and the main power connection.
4. Carefully lay the dishwasher on its back to access the components underneath.
5. Locate the wash pump and motor assembly. Disconnect the wire harnesses and use pliers to release the clamps on the attached hoses.
6. Remove the old pump assembly and install the new one (Part #154844301, #807473201, or #154853801), ensuring all hose clamps are tight and wires are securely connected.
7. Tip the dishwasher upright, reconnect all lines, slide it back into place, restore power and water, and run a test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154853801
- 807473201
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 3, 2026
How to Fix Electrolux Dishwasher Error I58
Error Code: I58 Difficulty: Moderate

Problem: Wash pump motor connection fault.

How to Fix I58 Error (Step-by-Step)
1. Disconnect the dishwasher from power at the circuit breaker and confirm the error stays cleared during a full test cycle.
2. Pull the dishwasher out from its installation and carefully place it on its back on a towel or blanket.
3. Locate the wash pump motor and its main wiring connector on the underside of the unit.
4. Inspect the wiring harness for any visible signs of damage, such as burnt plastic, broken wires, or loose pins in the connector.
5. Unplug and firmly reseat the connector to ensure a solid connection. Sometimes, vibrations can cause it to become loose.
6. If the wiring appears intact and the connection is secure, the fault is likely internal to the wash pump motor itself.
7. In this case, the entire wash pump assembly (Part #154844301, #807473201, or #154853801) must be replaced.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154853801
- 807473201
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 3, 2026
How to Fix Electrolux Dishwasher Error I59
Error Code: I59 Difficulty: Hard

Problem: Wash pump current read ADC fault.

How to Fix I59 Error (Step-by-Step)
1. Completely turn off the dishwasher by turning off the circuit breaker.
2. Remove the screws holding the lower front kickplate and remove it.
3. Locate the main control board. This error indicates the board’s internal circuitry for monitoring the wash pump has failed.
4. While a visual inspection for burn marks is good practice, this type of fault is often not visible.
5. The definitive repair for an ADC fault is the replacement of the main control board.
6. Carefully transfer the wire connections one by one from the old board to the new board (Part #154750503, #154807601, or #154663004).
7. Secure the new board, reinstall the kickplate, and restore power to verify the fix.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher

Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Verified Compatible Alternatives:
- 154750503
- 154807601
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Electrolux error codes: Electrolux Error Codes
June 3, 2026