Electrolux Dishwasher error code
Electrolux Dishwasher Error I58
Wash pump motor connection fault.
Wash pump motor connection fault.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Disconnect the dishwasher from power at the circuit
Disconnect the dishwasher from power at the circuit breaker and confirm the error stays cleared during a full test cycle.
- 2Pull the dishwasher out from its installation and
Pull the dishwasher out from its installation and carefully place it on its back on a towel or blanket.
- 3Locate the wash pump motor and its main
Locate the wash pump motor and its main wiring connector on the underside of the unit.
A quick explanation
What does I58 mean?
Wash pump motor connection fault.
The answer you came for
How to fix Electrolux dishwasher error I58
Start with the safest checks and work from simple to technical.
- 1
Disconnect the dishwasher from power at the circuit
Disconnect the dishwasher from power at the circuit breaker and confirm the error stays cleared during a full test cycle.
- 2
Pull the dishwasher out from its installation and
Pull the dishwasher out from its installation and carefully place it on its back on a towel or blanket.
- 3
Locate the wash pump motor and its main
Locate the wash pump motor and its main wiring connector on the underside of the unit.
- 4
Inspect the wiring harness for any visible signs
Inspect the wiring harness for any visible signs of damage, such as burnt plastic, broken wires, or loose pins in the connector.
- 5
Unplug and firmly reseat the connector to ensure
Unplug and firmly reseat the connector to ensure a solid connection. Sometimes, vibrations can cause it to become loose.
- 6
If the wiring appears intact and the connection
If the wiring appears intact and the connection is secure, the fault is likely internal to the wash pump motor itself.
- 7
In this case, the entire wash pump assembly
In this case, the entire wash pump assembly (Part #154844301, #807473201, or #154853801) must be replaced.
- 8
Turn the appliance off, wait about 2 minutes,
Turn the appliance off, wait about 2 minutes, then turn it back on.
Read the additional checks from the current guide
How to Fix I58 Error (Step-by-Step) Disconnect the dishwasher from power at the circuit breaker and confirm the error stays cleared during a full test cycle.Pull the dishwasher out from its installation and carefully place it on its back on a towel or blanket.Locate the wash pump motor and its main wiring connector on the underside of the unit.Inspect the wiring harness for any visible signs of damage, such as burnt plastic, broken wires, or loose pins in the connector.Unplug and firmly reseat the connector to ensure a solid connection. Sometimes, vibrations can cause it to become loose.If the wiring appears intact and the connection is secure, the fault is likely internal to the wash pump motor itself.In this case, the entire wash pump assembly (Part #154844301, #807473201, or #154853801) must be replaced.Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. Verified Compatible Alternatives:154853801807473201
Recommended part
Recommended part for this error code
Part listed in the current guide
OEM candidate: 154844301
Price noted in the current guide: $90-$260
Why this part is shown: It is associated with Electrolux Dishwasher error I58 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dishwasher model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dishwasher?
If repairing this dishwasher no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$499
Budget-friendly dishwashers in the $0-$499 range.
Shop Value Options on AmazonBest Overall
$500-$899
Balanced dishwashers in the $500-$899 range.
Shop Best Overall Options on AmazonPremium
$900-$2,000
Higher-end dishwashers in the $900-$2,000 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Electrolux Dishwasher Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.