Category: Electrolux

  • How to Fix Electrolux Dryer Error E12

    How to Fix Electrolux Dryer Error E12

    Error Code: E12 Difficulty: Easy

    Problem: Non-fatal R/W error; problem reading or writing to memory or input/output.

    How to Fix E12 Error (Step-by-Step)

    1. Stop the current drying cycle by pressing the ‘Cancel’ button.
    2. Disconnect the dryer from its power source by unplugging it from the wall.
    3. Leave the dryer unplugged for 10 minutes to allow the internal memory to clear and reset.
    4. Reconnect the power cord securely into the outlet and confirm the error stays cleared during a full test cycle.
    5. Attempt to run a new cycle to see if the error has cleared.
    6. This error is often a temporary glitch, but if it reappears frequently, it could indicate a more serious issue with the control board.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E11

    How to Fix Electrolux Dryer Error E11

    Error Code: E11 Difficulty: Easy

    Problem: Checksum Error; problem with communications or memory did not check.

    How to Fix E11 Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Stop’ button to end the current cycle.
    2. Unplug the dryer’s power cord from the wall outlet and confirm the error stays cleared during a full test cycle.
    3. Wait for at least 5 minutes. This allows the internal microprocessor to fully reset.
    4. Plug the dryer back into the wall outlet and confirm the error stays cleared during a full test cycle.
    5. Select a new drying cycle and press ‘Start’ and confirm the error stays cleared during a full test cycle.
    6. If the error persists after multiple attempts, there may be an issue with the main control board requiring professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error E10

    How to Fix Electrolux Dryer Error E10

    Error Code: E10 Difficulty: Hard

    Problem: General EEPROM fault; problem with communication between EEPROM and the microprocessor.

    How to Fix E10 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to ensure safety.
    2. Remove the top panel of the dryer by unscrewing the screws at the back or top edge.
    3. Locate the main electronic control board, which is typically a green circuit board housed in a plastic case.
    4. Carefully disconnect all wire harnesses connected to the board. It’s helpful to take a photo beforehand for reference.
    5. Remove the screws or release the clips holding the old control board in place and remove it.
    6. Install the new control board (part number 137544800), securing it with the screws or clips.
    7. Reconnect all wire harnesses to the new board, referencing your photo to ensure correct placement, then reassemble the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error CF

    How to Fix Electrolux Dryer Error CF

    Error Code: CF Difficulty: Hard

    Problem: Not specified in search results.

    How to Fix CF Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure safety during the repair.
    2. Access the main electronic control board, which typically requires removing the top or rear panel of the dryer.
    3. Take a detailed photograph of all the wire connections on the board to serve as a guide for reassembly.
    4. Systematically disconnect each wire harness from the control board. These connectors have locking tabs that need to be depressed.
    5. Remove the screws or release the clips that secure the control board to the dryer frame and carefully remove the old board.
    6. Mount the new control board in the same position and secure it.
    7. Using your photograph as a reference, reconnect all wire harnesses to the correct terminals on the new board. Reinstall the dryer panel, plug in the appliance, and run a cycle to confirm the fix.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304510361

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error CE

    How to Fix Electrolux Dryer Error CE

    Error Code: CE Difficulty: Hard

    Problem: Configuration error.

    How to Fix CE Error (Step-by-Step)

    1. Disconnect the dryer from the power supply by unplugging the power cord.
    2. Remove the top panel of the dryer by taking out the screws at the back.
    3. Locate the main control board (also called the electronic control board) in its plastic housing.
    4. Take a clear picture of the wiring connections to the board to ensure you can reconnect them correctly.
    5. Carefully disconnect all the wire harnesses from the old board. Press the release tabs on each connector as you gently pull.
    6. Remove the old control board from its housing. It may be held by clips or screws.
    7. Place the new control board into the housing, ensuring it is secure. Reconnect all wiring harnesses based on your photo, then reattach the top panel and test the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304515410

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error C8

    How to Fix Electrolux Dryer Error C8

    Error Code: C8 Difficulty: Moderate

    Problem: Indicates a problem with the temperature sensor.

    How to Fix C8 Error (Step-by-Step)

    1. Ensure the dryer is unplugged from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Locate the temperature sensor (thermistor). It is usually found on the blower housing or the heater duct at the rear of the dryer. You will likely need to remove the rear panel.
    3. Disconnect the two wires attached to the sensor. The connector can be pulled straight off.
    4. Remove the screw that holds the temperature sensor in place and remove the old sensor.
    5. Install the new temperature sensor and secure it with the screw.
    6. Reconnect the wire connector to the new sensor and confirm the error stays cleared during a full test cycle.
    7. Replace the rear panel, plug the dryer in, and test it by starting a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error C6

    How to Fix Electrolux Dryer Error C6

    Error Code: C6 Difficulty: Moderate

    Problem: Not specified in search results.

    How to Fix C6 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent electrical shock.
    2. The error often relates to the moisture sensor. Locate the two metal bars inside the drum, typically near the lint filter opening.
    3. Clean the surfaces of these sensor bars thoroughly with a soft cloth and a small amount of rubbing alcohol. This removes any film from fabric softener or dryer sheets.
    4. Dry the sensors completely with a clean cloth and confirm the error stays cleared during a full test cycle.
    5. Ensure the dryer is level by adjusting the feet, as an unlevel dryer can affect sensor readings.
    6. Check that the dryer is connected to a properly grounded electrical outlet, as improper grounding can interfere with the sensor’s operation.
    7. Plug the dryer back in and run a cycle to see if the issue is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error C2

    How to Fix Electrolux Dryer Error C2

    Error Code: C2 Difficulty: Moderate

    Problem: Drainage problem.

    How to Fix C2 Error (Step-by-Step)

    1. Disconnect the dryer from its power source and confirm the error stays cleared during a full test cycle.
    2. For condensing dryers, locate the drain pump, which is usually at the bottom front of the appliance. You may need to remove a lower access panel.
    3. Place a shallow pan and towels under the pump to catch any residual water.
    4. Disconnect the hoses attached to the pump. Be prepared for water to spill out.
    5. Inspect the pump inlet and outlet ports, as well as the hoses, for any lint or debris that could cause a blockage. Clear any obstructions found.
    6. If no blockage is found, the pump may have failed. Disconnect the electrical connector, remove the mounting screws, and replace it with the new pump.
    7. Reconnect the hoses and electrical connector, secure the access panel, and test the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error 9C

    How to Fix Electrolux Dryer Error 9C

    Error Code: 9C Difficulty: Hard

    Problem: Software/config errors.

    How to Fix 9C Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure your safety.
    2. Access the main control board, which is typically located behind the top or rear panel. You will need a screwdriver to remove the panel screws.
    3. Before disconnecting anything, take a clear photo of the wire connections to the control board to use as a reference.
    4. Carefully disconnect all wire harnesses from the old control board. Most connectors have a small tab that needs to be pressed to release.
    5. Remove the screws or clips holding the old control board in place and gently lift it out.
    6. Install the new control board, securing it with the original screws or clips.
    7. Reconnect all wire harnesses to the new board, referring to the photo you took earlier to ensure they are in the correct positions. Reassemble the dryer and test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304505611

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Dryer Error 41

    How to Fix Electrolux Dryer Error 41

    Error Code: 41 Difficulty: Easy

    Problem: Door opened at start.

    How to Fix 41 Error (Step-by-Step)

    1. Open the dryer door completely and confirm the error stays cleared during a full test cycle.
    2. Check for any clothing, lint, or other items that may be blocking the door from closing properly.
    3. Remove any obstructions you find and confirm the error stays cleared during a full test cycle.
    4. Close the door firmly until you hear a distinct ‘click’ sound, which indicates the latch is engaged.
    5. Press the ‘Start’ button again to begin the drying cycle.
    6. If the door does not seem to latch securely, inspect the door latch mechanism for any visible damage.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes