Category: Washer

  • How to Fix Amana Washer Error F0E8

    How to Fix Amana Washer Error F0E8

    Error Code: F0E8 Difficulty: Moderate

    Problem: Too much residual water has been detected in the washer.

    How to Fix F0E8 Error (Step-by-Step)

    1. Unplug the washer from its power source and turn off the water supply valves.
    2. Place towels on the floor and carefully tilt the washer forward, resting it against a wall for stability to access the bottom.
    3. Locate the drain pump, which is a small component with two large hoses attached.
    4. Put a shallow pan underneath the hoses to catch water. Use pliers to squeeze the clamps on the hoses and slide them off the pump ports.
    5. Disconnect the electrical wire connector from the pump and confirm the error stays cleared during a full test cycle.
    6. Remove the mounting screws that hold the old pump in place and take it out.
    7. Install the new pump, secure it with the screws, and reattach the hoses, clamps, and electrical connector before carefully returning the washer to its upright position.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error F0E7

    How to Fix Amana Washer Error F0E7

    Error Code: F0E7 Difficulty: Easy

    Problem: Items were detected in the washer during the Clean Washer cycle.

    How to Fix F0E7 Error (Step-by-Step)

    1. Press the ‘Power’ button to cancel the ‘Clean Washer’ cycle.
    2. Open the washer lid and look inside the drum and confirm the error stays cleared during a full test cycle.
    3. Remove any forgotten items such as clothes, towels, or other laundry.
    4. The ‘Clean Washer’ cycle is meant to clean the inside of the machine and must be run completely empty.
    5. Close the lid securely and confirm the error stays cleared during a full test cycle.
    6. Select the ‘Clean Washer’ cycle again and press ‘Start’ with the now-empty drum.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error F0 E2

    How to Fix Amana Washer Error F0 E2

    Error Code: F0 E2 Difficulty: Easy

    Problem: Over Suds Condition

    How to Fix F0 E2 Error (Step-by-Step)

    1. Do not add more detergent. The washer has detected too many suds and is attempting to correct the issue automatically.
    2. Allow the washer to complete its cycle. It may add extra rinses, which will extend the cycle time.
    3. After the cycle finishes, remove the laundry and confirm the error stays cleared during a full test cycle.
    4. To clear out residual suds from the machine, run a ‘Clean Washer’ cycle or a ‘Normal’ cycle on the hottest setting with one cup of white vinegar and no clothes.
    5. In the future, always use detergent specifically labeled for High-Efficiency (HE) machines.
    6. Reduce the amount of HE detergent used per load, as modern detergents are highly concentrated.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error F# E#

    How to Fix Amana Washer Error F# E#

    Error Code: F# E# Difficulty: Easy

    Problem: System Code Error

    How to Fix F# E# Error (Step-by-Step)

    1. Press the ‘Power’ button to cancel the cycle and turn off the machine.
    2. Disconnect the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    3. Let the washer remain without power for at least 5 minutes to reset the main control board.
    4. During this time, confirm the wall outlet is functional by testing it with a small lamp or other device.
    5. Plug the washer back in, ensuring a firm connection and confirm the error stays cleared during a full test cycle.
    6. Start a ‘Rinse & Spin’ cycle to check if the system error has been resolved.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error ERR

    How to Fix Amana Washer Error ERR

    Error Code: ERR Difficulty: Easy

    Problem: General Error

    How to Fix ERR Error (Step-by-Step)

    1. Press the ‘Start/Stop’ button to pause the current operation.
    2. Press the ‘Power’ button to turn the washer off completely.
    3. Unplug the washer’s power cord from the wall outlet and confirm the error stays cleared during a full test cycle.
    4. Wait for 5 minutes to allow the internal electronics to fully reset.
    5. Plug the power cord securely back into the outlet and confirm the error stays cleared during a full test cycle.
    6. Select a new wash cycle and press ‘Start’ to confirm the error is cleared.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error DOOR LOCKED

    How to Fix Amana Washer Error DOOR LOCKED

    Error Code: DOOR LOCKED Difficulty: Hard

    Problem: Indicates that the washer door is locked and cannot be opened.

    How to Fix DOOR LOCKED Error (Step-by-Step)

    1. Begin by unplugging the washer from the wall outlet to ensure your safety. Turn off the hot and cold water supply valves connected to the washer.
    2. Open the washer door. Use a Phillips screwdriver to remove the two screws that fasten the door lock assembly to the front panel of the machine.
    3. Locate the metal spring clamp that holds the large rubber door boot seal against the front panel. Carefully pry this clamp off using a spring expansion tool or pliers and set it aside.
    4. Gently peel the rubber door boot seal away from the front panel opening. You only need to create enough space to reach your hand behind the panel to access the door lock.
    5. Reach inside the opening and find the door lock assembly. Press the small tab on the wire harness connector to unplug it from the lock. You can now completely remove the old lock assembly from the washer.
    6. Position the new door lock assembly in place and securely plug in the wire harness connector. Align the lock with the screw holes on the front panel and reinstall the two screws you removed earlier.
    7. Carefully re-seat the rubber door boot seal onto the lip of the front panel, ensuring it is smooth and even. Reinstall the metal spring clamp to secure the boot seal. Plug the washer back in, turn the water on, and run a test cycle to confirm the door locks and the error is gone.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • W10804741
    • W10837741
    • W11307244

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error DONE LIGHT ON

    How to Fix Amana Washer Error DONE LIGHT ON

    Error Code: DONE LIGHT ON Difficulty: Easy

    Problem: Cycle Finished

    How to Fix DONE LIGHT ON Error (Step-by-Step)

    1. Recognize that the ‘Done’ light is a simple notification that the wash cycle has successfully completed.
    2. The machine has finished all washing, rinsing, and spinning stages.
    3. The door will be unlocked and safe to open and confirm the error stays cleared during a full test cycle.
    4. Open the washer door and transfer your clean clothes to the dryer or a clothesline.
    5. For best machine care, leave the washer door open for a while to allow the interior to dry completely.
    6. Press the ‘Power’ button to turn off the display and the machine.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error DETERGENT LOW

    How to Fix Amana Washer Error DETERGENT LOW

    Error Code: DETERGENT LOW Difficulty: Easy

    Problem: The detergent level in the bulk dispenser is low and needs to be refilled.

    How to Fix DETERGENT LOW Error (Step-by-Step)

    1. Acknowledge this message as a simple reminder that the bulk detergent dispenser needs to be refilled soon.
    2. Locate and pull out the bulk dispenser drawer, which is usually on the top-left side of the washer.
    3. Identify the compartment for liquid detergent and confirm the error stays cleared during a full test cycle.
    4. Carefully pour High-Efficiency (HE) liquid detergent into the compartment and confirm the error stays cleared during a full test cycle.
    5. Be sure not to fill past the ‘Max Fill’ line indicated inside the dispenser.
    6. Close the dispenser drawer securely. The message should now be gone.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error CYCLE COMPLETE LIGHT ON

    How to Fix Amana Washer Error CYCLE COMPLETE LIGHT ON

    Error Code: CYCLE COMPLETE LIGHT ON Difficulty: Easy

    Problem: Cycle Finished

    How to Fix CYCLE COMPLETE LIGHT ON Error (Step-by-Step)

    1. Understand that this light is an indicator that the selected wash cycle has finished successfully.
    2. The washer door will be unlocked, allowing you to open it.
    3. Open the door and remove your clean laundry promptly to prevent mildew.
    4. To help the washer drum air out and stay fresh, leave the door slightly ajar.
    5. Press the ‘Power’ button to turn the machine off and clear the light.
    6. The light will also typically turn off on its own after a set period of time.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Amana Washer Error CL

    How to Fix Amana Washer Error CL

    Error Code: CL Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix CL Error (Step-by-Step)

    1. Recognize that ‘CL’ on the display means the Control Lock or Child Lock feature is activated, which disables the buttons.
    2. Look for a button on the control panel specifically labeled ‘Control Lock’ or with a small lock icon next to it.
    3. Press and hold this specific button for three full seconds.
    4. For some models, you may need to press and hold a specific combination of two buttons simultaneously for three seconds. Check the button labels for text like ‘Hold 3 Sec to Lock’.
    5. The ‘CL’ code will disappear from the display once the controls are unlocked.
    6. You can now operate the washer normally and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Washer

    Focused repair path: washer fill, drain, spin, lock, pressure, motor, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Unplug the washer for one minute, then restart only to confirm whether the same code returns after a clean power cycle.
    2. Check load balance, detergent level, supply valves, inlet screens, drain hose height, and the drain path before replacing electronic parts.
    3. Inspect the lid or door lock, strike, harness, and connector if the symptom involves start, lock, or spin behavior.
    4. Match the timing of the fault to the likely part path: inlet valve, pressure sensor, drain pump, motor, lock assembly, wiring, or control.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool washer drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.

      Search Amazon for Whirlpool washer drain pump

    • Whirlpool washer water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: fill, slow-fill, and valve-related symptoms after supply checks.

      Search Amazon for Whirlpool washer water inlet valve

    • Whirlpool washer control board
      Common replacement category: Main control board
      Fit note: Exact OEM part number varies by complete Amana washer model number. Confirm compatibility before buying.
      Why this category can matter: repeating control or communication faults after connector checks.

      Search Amazon for Whirlpool washer control board

    Before ordering: match the part to the complete Amana washer model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Amana error codes: Amana Error Codes

    When It’s Better to Replace Than Repair

    Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
    Here are a few signs it may be time to shop for a new one:

    For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.

    • Appliance over 8-10 years old
    • Repair cost over 50% of replacement
    • Multiple recent breakdowns
    • Major component failure

    Recommended Replacement Options

    Budget Option

    Top Rated Washers Under $600

    • Amazon’s Highest-Rated Value Models
    • Free ‘Room of Choice’ Delivery Available
    • Professional Haul-away Options at Checkout


    View Top Rated Models & Delivery Options

    Mid-Range Option

    Top Rated Washers $600 to $1,000

    • Best-Sellers with Thousands of 5-Star Reviews
    • Expert Installation & Hookup Services available
    • Protection Plans for Long-Term Peace of Mind


    View Top Rated Models & Delivery Options

    Premium Option

    Top Rated Washers Over $1,000

    • Top-of-the-Line Performance & Technology
    • White-Glove Delivery and Haul-away eligible
    • Comprehensive Warranty & Support Options


    View Top Rated Models & Delivery Options

    Why Upgrade via Amazon?

    • Fast, Scheduled Delivery – You pick the date and time
    • Expert Installation – Professional setup available for most models
    • Old Appliance Haul-away – They’ll take your broken unit when they leave
    • Easy Returns – Buy with confidence from a leader in customer service

    As an Amazon Associate, we earn from qualifying purchases.