Category: Amana

  • How to Fix Amana Washer Error LOC

    How to Fix Amana Washer Error LOC

    Error Code: LOC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LOC Error (Step-by-Step)

    1. Find the button on your Amana washer’s control panel that is designated for the ‘Control Lock’ function, often marked with a padlock symbol.
    2. Press and hold this specific button for approximately 3 to 5 seconds.
    3. You should see the ‘Control Lock’ indicator light on the display turn off.
    4. This indicates that the control panel is now unlocked and fully functional.
    5. You can now operate the washer as usual by selecting your desired cycle and settings.
    6. To re-enable the lock, repeat the process by holding the same button for another 3-5 seconds.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LD

    How to Fix Amana Washer Error LD

    Error Code: LD Difficulty: Hard

    Problem: Long Drain Time

    How to Fix LD Error (Step-by-Step)

    1. Unplug the washer from the power outlet to prevent any electrical accidents.
    2. Place towels and a shallow pan around the base of the washer to catch water.
    3. Carefully tilt the washer forward, resting it securely against a wall to access the drain pump, usually located at the bottom rear.
    4. Squeeze the clamp on the drain hose connected to the pump and slide it off, directing the hose into the pan to drain remaining water.
    5. Inspect the pump inlet and the drain hose for any obstructions like socks, lint, or other small items and remove them.
    6. If the hose is clear and the pump impeller doesn’t turn freely, the drain pump motor is likely faulty.
    7. To replace it, disconnect the wire harness, remove the mounting screws, install the new pump, and reconnect all hoses and wires before carefully setting the washer upright.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LDL

    How to Fix Amana Washer Error LDL

    Error Code: LDL Difficulty: Moderate

    Problem: Lid Lock Failure

    How to Fix LDL Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure your safety.
    2. Locate the lid lock assembly. It is typically found beneath the main top of the washer, near the opening where the lid closes.
    3. To access the lock, you will likely need to raise the main top. Look for and remove the screws at the back or sides of the washer top panel.
    4. Carefully disconnect the wire harness that plugs into the lid lock assembly. There is usually a small clip you need to press to release it.
    5. Remove the screws holding the old lid lock in place and take the old assembly out.
    6. Position the new lid lock assembly (part W11307244, W10810403, or W11253733) and secure it with the screws.
    7. Reconnect the wire harness, lower the main top back into position, and replace its screws.
    8. Plug the washer back in and start a cycle to confirm the new lock works correctly.

    Verified Compatible Alternatives:

    • W11253733 (Lid Lock Assembly)
    • W11307244 (Lid Lock Assembly)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LDU

    How to Fix Amana Washer Error LDU

    Error Code: LDU Difficulty: Easy

    Problem: Lid Unlock Failure

    How to Fix LDU Error (Step-by-Step)

    1. Press the ‘Start/Stop’ or ‘Cancel’ button one time to pause the current cycle.
    2. Wait for up to three minutes for the washer to come to a complete stop and for the internal mechanism to disengage the lock.
    3. If the lid does not unlock after a few minutes, unplug the washer from the power outlet.
    4. Let the washer sit without power for 10 minutes. This will allow the machine’s internal computer to fully reset.
    5. Plug the washer back into the power outlet. The lid should now be unlocked.
    6. As a final step if it’s still locked, select the ‘Drain & Spin’ cycle and press start. Allowing this cycle to complete will usually end with the lid unlocking.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LID

    How to Fix Amana Washer Error LID

    Error Code: LID Difficulty: Moderate

    Problem: Lid Open

    How to Fix LID Error (Step-by-Step)

    1. First, simply open and firmly close the lid to make sure it is not being blocked by any clothing and that it is fully seated.
    2. If the error continues, unplug the washer from the electrical outlet for safety.
    3. Inspect the plastic striker piece on the lid itself. Make sure it is not cracked, broken, or bent out of shape, as this can prevent it from properly engaging the lock.
    4. To replace the lock, raise the top panel of the washer by removing the retaining screws.
    5. Unplug the electrical connector from the lid lock assembly and remove the screws that mount it to the washer body.
    6. Install the new lid lock assembly (part W11307244, W10810403, or W11253733), ensuring it is securely screwed in place.
    7. Reconnect the electrical plug, re-secure the top panel, plug the washer in, and start a test cycle to ensure the error is gone.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11253733 (Lid Lock Assembly)
    • W11307244 (Lid Lock Assembly)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error LID LIGHT FLASHING

    How to Fix Amana Washer Error LID LIGHT FLASHING

    Error Code: LID LIGHT FLASHING Difficulty: Moderate

    Problem: Lid Open

    How to Fix LID LIGHT FLASHING Error (Step-by-Step)

    1. Open the lid and check for any items, like a sock or shirt sleeve, that might be caught and preventing the lid from closing completely. Close it firmly.
    2. Unplug the washing machine from its power source to avoid any risk of electric shock during the repair.
    3. Examine the plastic strike on the lid that inserts into the lock. If it appears damaged or broken, the lock will not activate.
    4. Lift the washer’s top panel to access the lid lock mechanism below.
    5. Disconnect the wire harness attached to the lid lock and then unscrew the lock from the machine’s frame.
    6. Mount the new lid lock assembly (part W11307244, W10810403, or W11253733) and reconnect its wire harness.
    7. Lower the top panel, plug the washer in, and begin a new cycle to verify the repair and ensure the light is no longer flashing.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W11253733 (Lid Lock Assembly)
    • W11307244 (Lid Lock Assembly)

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error MULTIPLE LIGHTS FLASHING

    How to Fix Amana Washer Error MULTIPLE LIGHTS FLASHING

    Error Code: MULTIPLE LIGHTS FLASHING Difficulty: Easy

    Problem: General Error

    How to Fix MULTIPLE LIGHTS FLASHING Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Stop’ button to attempt to clear the general error code.
    2. If the lights continue to flash, unplug the washer from the wall outlet.
    3. Let the washer remain unplugged for at least five minutes. This action performs a hard reset of the main control board.
    4. During this time, check that the hot and cold water supply hoses are fully turned on and not kinked.
    5. Plug the washer back in and confirm the error stays cleared during a full test cycle.
    6. Select a simple ‘Rinse & Spin’ cycle and press ‘Start’ to see if the machine operates normally.
    7. If the error returns, it may indicate a more complex internal issue requiring professional service.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error PF

    How to Fix Amana Washer Error PF

    Error Code: PF Difficulty: Easy

    Problem: Power Failure

    How to Fix PF Error (Step-by-Step)

    1. This code indicates the washer lost power during a cycle. First, check that the power cord is still firmly plugged into the wall outlet.
    2. Go to your home’s circuit breaker panel and find the breaker that controls the laundry room. If it has tripped, it will be in the middle position. Flip it completely off and then back on to reset it.
    3. To confirm the outlet has power, try plugging in a small appliance you know works, like a phone charger or a lamp.
    4. If the outlet is working, the ‘PF’ code is just an alert. You can resume the interrupted cycle by pressing and holding the ‘Start’ button for a few seconds.
    5. If you prefer to begin a new wash, press the ‘Cancel’ or ‘Power’ button to clear the cycle, then make your new selection.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error RINSE LIGHT ON

    How to Fix Amana Washer Error RINSE LIGHT ON

    Error Code: RINSE LIGHT ON Difficulty: Easy

    Problem: Rinsing

    How to Fix RINSE LIGHT ON Error (Step-by-Step)

    1. This light is not an error indicator. It is a status light letting you know the washer is currently in the rinse phase of the wash cycle.
    2. No action is needed. The light will turn off automatically as the machine progresses to the next part of the cycle, such as spin or drain.
    3. If you wish to add a garment or fabric softener, press the ‘Start/Stop’ button to pause the cycle.
    4. Wait for the lid to unlock, add your item, and close the lid.
    5. Press the ‘Start/Stop’ button again to resume the cycle from where it left off.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error SD

    How to Fix Amana Washer Error SD

    Error Code: SD Difficulty: Easy

    Problem: Suds Detected

    How to Fix SD Error (Step-by-Step)

    1. This code means the washer has detected too many suds and is not an error. Do not add any more water or try to open the lid.
    2. The washer will automatically take steps to reduce the suds, which usually involves pausing the tumbling and adding more water. This will add time to the overall cycle.
    3. Allow the cycle to complete on its own. The machine is designed to handle this situation.
    4. After the load is finished, remove the clothes and run a full wash cycle on hot with the washer empty. This will clean out any excess detergent residue.
    5. For future loads, ensure you are using a detergent marked ‘HE’ for High-Efficiency machines.
    6. Reduce the amount of HE detergent you use, as modern detergents are highly concentrated. Use the measurement lines on the cap as a guide for your load size.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.