Skip to main content
Appliance Fix Guide

Amana Dishwasher error code

Amana Dishwasher Error 1-2

Control software issue - damaged or corrupted memory on control board or incompatible software.

Control software issue - damaged or corrupted memory on control board or incompatible software.

Updated Aug 18, 2026
informationalno_parts
Amana dishwasher repair guide for error 1-2
Error code1-2Dishwasher

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Power Cycle: Turn off the circuit breaker for the dishwasher for at least 5 minutes to perform a hard reset of the control board.

  2. 2
    Check 2

    Enter Diagnostic Mode: On some models, you can enter a diagnostic mode to help confirm the control board fault. The method for this varies by model, so consult your owner's manual or online resources.

A quick explanation

What does 1-2 mean?

Control software issue - damaged or corrupted memory on control board or incompatible software.

The answer you came for

How to fix Amana dishwasher error 1-2

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Disconnect the dishwasher from power by unplugging it from the wall outlet or shutting off the corresponding circuit breaker in your home's electrical panel.

  2. 2

    Step 2

    2. Open the dishwasher door and remove the screws holding the inner door panel to the outer panel. These are typically located around the perimeter of the inner door.

  3. 3

    Step 3

    3. Carefully separate the inner and outer door panels to expose the internal components. The main control board is usually a green circuit board housed in a plastic case, often located at the top or side of the door assembly.

  4. 4

    Step 4

    4. Take a clear photo of the wiring connections on the old control board to use as a reference. This will ensure you reconnect everything correctly on the new board.

  5. 5

    Step 5

    5. Gently disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.

  6. 6

    Step 6

    6. Remove the screws or release the clips holding the old control board in its housing and carefully take it out.

  7. 7

    Step 7

    7. Install the new control board, secure it in place, and reconnect all the wire harnesses by referring to the photo you took earlier. Ensure each connector is firmly seated.

  8. 8

    Step 8

    8. Reassemble the dishwasher door panels, restore power to the appliance, and run a test cycle to confirm the repair.

Read the additional checks from the current guide

How to Fix 1-2 Error (Step-by-Step) Disconnect the dishwasher from power by unplugging it from the wall outlet or shutting off the corresponding circuit breaker in your home's electrical panel.Open the dishwasher door and remove the screws holding the inner door panel to the outer panel. These are typically located around the perimeter of the inner door.Carefully separate the inner and outer door panels to expose the internal components. The main control board is usually a green circuit board housed in a plastic case, often located at the top or side of the door assembly.Take a clear photo of the wiring connections on the old control board to use as a reference. This will ensure you reconnect everything correctly on the new board.Gently disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.Remove the screws or release the clips holding the old control board in its housing and carefully take it out.Install the new control board, secure it in place, and reconnect all the wire harnesses by referring to the photo you took earlier. Ensure each connector is firmly seated.Reassemble the dishwasher door panels, restore power to the appliance, and run a test cycle to confirm the repair.

What to Check Next on This Amana Dishwasher Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model. Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect. Recommended Parts to Check No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims. Whirlpool dishwasher drain pump Common replacement category: Drain pump Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying. Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked. Search Amazon for Whirlpool dishwasher drain pump Whirlpool dishwasher water inlet valve Common replacement category: Water inlet valve Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying. Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks. Search Amazon for Whirlpool dishwasher water inlet valve Whirlpool dishwasher control board Common replacement category: Electronic control board Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying. Why this category can matter: repeating error-code or control faults after wiring and latch checks. Search Amazon for Whirlpool dishwasher control board Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Main control board failure
  • Software or memory corruption on the control board

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

No replacement part recommended for this code

The researched guidance for Amana Dishwasher error 1-2 points to user-action and diagnostic steps above rather than a mapped replacement part. We will not invent a part or send you to an unrelated product.

Replacement options

Ready to replace your dishwasher?

If repairing this dishwasher no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Amana Dishwasher Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

The form will be enabled after the existing subscriber database and PDF delivery are connected securely.

No spam. Unsubscribe anytime.