Category: Dryer

Error Code: F23 Difficulty: Hard

Problem: Fault in the exhaust/outlet thermistor.

How to Fix F23 Error (Step-by-Step)

1. Ensure the dryer is completely unplugged from the power source.
2. Remove the screws from the back of the dryer that hold the top panel in place, then slide the panel off.
3. Remove the control panel console by taking out its mounting screws.
4. Open the dryer door and remove the screws located inside the door frame that secure the front panel.
5. Carefully lean the front panel forward, locate the thermistor on the blower housing, and disconnect its wire harness.
6. Use a screwdriver to remove the single screw mounting the thermistor to the housing and remove the old part.
7. Secure the new thermistor with the screw, plug in the wire harness, and reassemble the front panel, control console, and top panel.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: ERR Difficulty: Moderate

Problem: The dryer door is not completely closed or latched.

How to Fix ERR Error (Step-by-Step)

1. First, open the dryer door and close it firmly to ensure the latch is fully engaged. Check for any clothing or items obstructing the door.
2. If the error continues, unplug the dryer from the power outlet.
3. Open the dryer door and locate the door switch assembly inside the door frame.
4. Use a putty knife to release the two clips holding the top panel down, located in the gap between the top and front panels. Hinge the top panel up and back.
5. From the inside, locate the door switch. Unscrew it from the front panel and disconnect its wire harness.
6. Connect the new door switch (Parts: 279570, WPW10610880), screw it back into the front panel.
7. Lower the top panel and snap it back into place. Plug the dryer in and test by starting a cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: E2 Difficulty: Moderate

Problem: Indicates a shorted thermistor, causing the dryer to misread the temperature.

How to Fix E2 Error (Step-by-Step)

1. Unplug the dryer from the power source to prevent electrical shock.
2. Remove the lower front panel to gain access to the internal components. This panel is often held by two screws at the bottom or clips at the top.
3. Find the thermistor mounted on the exhaust blower housing. It’s a small plastic sensor with two wires leading to it.
4. Carefully unplug the wire connector from the old thermistor and confirm the error stays cleared during a full test cycle.
5. Use a nut driver or screwdriver to remove the single screw securing the thermistor to the housing.
6. Place the new thermistor (Part: WP8577274) into the housing, fasten it with the screw, and plug the wire connector back in until it clicks.
7. Reattach the lower panel, restore power to the dryer, and verify the fix by starting a new cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: E1 Difficulty: Moderate

Problem: Indicates an issue with the thermistor, specifically an open circuit. This can be caused by a faulty thermistor or a wiring problem.

How to Fix E1 Error (Step-by-Step)

1. Disconnect the dryer from the wall outlet to ensure safety.
2. Access the thermistor, which is typically located on the blower housing. You may need to remove the lower front access panel by unscrewing it or releasing clips at the top.
3. Locate the thermistor on the blower housing. It is a small black or gray component with a two-wire connector.
4. Disconnect the wire harness attached to the thermistor. Squeeze the tab on the connector to release it.
5. Remove the single screw, usually a quarter-inch hex head, that holds the thermistor in place.
6. Install the new thermistor (Part: WP8577274), secure it with the screw, and firmly reconnect the wire harness.
7. Reassemble the access panel, plug the dryer back in, and run a test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: CHECK VENT Difficulty: Easy

Problem: Indicates that the dryer vent is clogged or there is restricted airflow.

How to Fix CHECK VENT Error (Step-by-Step)

1. Pull out the dryer’s lint screen and clean it of all lint. If it has a waxy buildup from dryer sheets, wash it with a soft brush and soapy water, then let it dry completely.
2. Unplug the dryer from the wall to ensure your safety during the next steps.
3. Carefully pull the dryer away from the wall and detach the vent hose from the back of the machine.
4. Clear any lint buildup from the dryer’s exhaust port and from the inside of the vent hose itself.
5. Inspect the vent hose for any sections that are crushed or kinked, as this can severely limit airflow. Straighten them out.
6. Use a specialized vent cleaning kit with a long brush to clean out the entire length of the ductwork that runs to the exterior of your home.
7. Go outside and ensure the external vent flap is clean and can open and close without obstruction.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 88 Difficulty: Easy

Problem: All display segments are lit up. This is a normal part of the diagnostic test mode to ensure the display is working correctly.

How to Fix 88 Error (Step-by-Step)

1. This display is not an error but indicates the dryer is in a check test mode.
2. To exit this mode, press and hold the ‘Start’ or ‘Cancel’ button for a few seconds.
3. If the display does not return to normal, the next step is to reset the machine’s main board.
4. Unplug the dryer from its power source for at least 2 minutes.
5. Plug the dryer back in. The display should now be clear and ready for normal cycle selection.
6. If the ’88’ display is stuck and will not clear after a power cycle, the display control board may be faulty and require professional service.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 6E Difficulty: Easy

Problem: Service Required.

How to Fix 6E Error (Step-by-Step)

1. Attempt to clear the error by pressing the ‘Cancel’ or ‘Stop’ button on the control panel.
2. If the code persists, unplug the dryer from the wall outlet or switch off the power at the home’s circuit breaker panel.
3. Wait for a minimum of 5 minutes before restoring power. This process can reset the dryer’s internal checks.
4. Plug the dryer back in or flip the circuit breaker on.
5. Try to initiate a drying cycle and confirm the error stays cleared during a full test cycle.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 3E Difficulty: Easy

Problem: Service Required.

How to Fix 3E Error (Step-by-Step)

1. First, try to clear the code by pressing the ‘Stop’ or ‘Cancel’ button.
2. If the code remains, perform a power cycle by unplugging the dryer from the electrical outlet or shutting it off at the circuit breaker.
3. Let the dryer remain without power for at least 5 minutes. This allows the internal computer to perform a hard reset.
4. Restore power by plugging the unit back in or turning the breaker on.
5. Select a new cycle and press ‘Start’ to see if the error has cleared.
6. If the ‘3E’ code returns, it signifies an internal component failure that requires diagnosis and repair by a professional service service.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 3 BEEPS Difficulty: Moderate

Problem: Can indicate a variety of issues, including a problem with the door switch or water getting into the control panel.

How to Fix 3 BEEPS Error (Step-by-Step)

1. Disconnect the dryer from its power source by unplugging it from the wall outlet.
2. Open the dryer door and locate the door switch, which is typically a small plastic switch around the frame that the door presses when closed.
3. Check that the plastic peg or actuator on the door itself is not broken and aligns correctly with the switch.
4. To replace the switch, you may need to remove the dryer’s top or front panel to access its housing and wiring.
5. Carefully disconnect the wire harness from the old switch, release the locking tabs, and install the new one.
6. Reassemble the dryer, restore power, and test its operation and confirm the error stays cleared during a full test cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes

Error Code: 0E Difficulty: Moderate

Problem: Indicates that there is too much water in the appliance. This could be due to a blocked pump or a faulty hot water valve that is not shutting off.

How to Fix 0E Error (Step-by-Step)

1. Turn off the hot and cold water supply valves connected to the appliance.
2. Unplug the dryer from the wall outlet to ensure safety.
3. Check the drain hose at the back for any visible kinks, twists, or blockages that could restrict water flow.
4. Place the end of the drain hose into a bucket to catch any trapped water and clear it from the line.
5. Inspect the water inlet hoses for any signs of damage, wear, or leaks.
6. This error often points to a faulty internal water pump or a stuck water inlet valve. These repairs involve handling water and electrical parts, so it is recommended to have a professional service service diagnose and complete the repair.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.

&tag=appliancefixg-20

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes