Category: Dishwasher

How to Fix Amana Dishwasher Error 8-1
Error Code: 8-1 Difficulty: Hard

Problem: Slow drain.

How to Fix 8-1 Error (Step-by-Step)
1. Disconnect Power and Water: Shut off the power to the dishwasher at the circuit breaker and turn off the water supply valve, usually located under the sink.
2. Check for Simple Clogs: Remove and clean the dishwasher’s filter at the bottom of the tub. Check the drain hose for any visible kinks or blockages.
3. Access the Drain Pump: Remove the lower access panel. The drain pump (Part No. W11087376) is located at the bottom of the dishwasher.
4. Disconnect the Old Pump: Place a towel under the pump to catch any residual water. Disconnect the wire harness and the hoses from the pump.
5. Remove Old Pump: Unclip or unscrew the old drain pump from its housing and remove it.
6. Install New Pump: Mount the new drain pump in place and reconnect the hoses and the electrical connector.
7. Reassemble and Test: Reattach the access panel, restore power and water, and run a drain cycle to check for leaks and proper function.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 8-2
Error Code: 8-2 Difficulty: Hard

Problem: Drain motor electrical problem.

How to Fix 8-2 Error (Step-by-Step)
1. Turn Off Power: For your safety, disconnect the dishwasher from the power supply by switching off the circuit breaker.
2. Access the Pump: Remove the bottom front toe and access panels of the dishwasher to get to the components underneath.
3. Locate Drain Pump: Find the drain pump (Part No. W11087376). It will have a wire harness and two hoses connected to it.
4. Disconnect Old Pump: Place a shallow pan and towel underneath to catch water. Carefully disconnect the wire harness and then the hoses from the pump.
5. Remove and Replace: Unmount the old pump from the dishwasher base. Install the new pump, ensuring it is securely mounted.
6. Reconnect Everything: Attach the hoses and the wire harness to the new pump. Ensure all connections are tight to prevent leaks.
7. Final Steps: Reinstall the access panels, turn the power back on, and run a test cycle to ensure the new pump operates correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 8-3
Error Code: 8-3 Difficulty: Hard

Problem: Drain stuck on.

How to Fix 8-3 Error (Step-by-Step)
1. Shut Off Power: Go to your home’s circuit breaker panel and turn off the power to the dishwasher.
2. Open the Door Panel: The control board is located inside the door. You will need to remove the series of screws around the perimeter of the inner door panel to separate it from the outer panel.
3. Locate the Control Board: With the panel open, you will see the main control board (Part No. WPW10285180 or W11413274) in a plastic housing.
4. Swap the Boards: Take a picture of the wiring for reference. Carefully disconnect all the wire connectors from the old board. Unclip it from its housing and install the new board.
5. Reconnect Wires: Using your photo as a guide, plug all the wire harnesses into the correct ports on the new control board.
6. Reassemble and Test: Put the inner door panel back on and secure it with the screws. Restore power at the breaker and run a cycle to confirm the repair.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10285180
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 9-1
Error Code: 9-1 Difficulty: Hard

Problem: Faulty Control Motor Drive Circuit or Sense Circuit.

How to Fix 9-1 Error (Step-by-Step)
1. Disconnect Power Source: Ensure your safety by turning off the circuit breaker that supplies power to the dishwasher.
2. Access the Control Board: Remove the screws holding the inner door panel in place. This will give you access to the dishwasher’s electronic components.
3. Identify the Board: Locate the main control board (Part No. WPW10285180 or W11413274). It is the central hub for all the wiring.
4. Photograph and Disconnect: Before disconnecting anything, take a clear picture of the wire layout. Then, carefully unplug all the wire harnesses from the board.
5. Replace the Board: Release any clips or screws holding the old board and remove it. Snap or screw the new control board into the same location.
6. Reconnect and Reassemble: Following your reference photo, reconnect all the wire harnesses to the new board. Secure the inner door panel back onto the dishwasher.
7. Power Up: Turn the circuit breaker back on and start a new cycle to verify that the dishwasher is functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10285180
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 9-2
Error Code: 9-2 Difficulty: Hard

Problem: Faulty Control Motor Drive Circuit or Sense Circuit.

How to Fix 9-2 Error (Step-by-Step)
1. Disconnect Power Source: Ensure your safety by turning off the circuit breaker that supplies power to the dishwasher.
2. Access the Control Board: Remove the screws holding the inner door panel in place. This will give you access to the dishwasher’s electronic components.
3. Identify the Board: Locate the main control board (Part No. WPW10285180 or W11413274). It is the central hub for all the wiring.
4. Photograph and Disconnect: Before disconnecting anything, take a clear picture of the wire layout. Then, carefully unplug all the wire harnesses from the board.
5. Replace the Board: Release any clips or screws holding the old board and remove it. Snap or screw the new control board into the same location.
6. Reconnect and Reassemble: Following your reference photo, reconnect all the wire harnesses to the new board. Secure the inner door panel back onto the dishwasher.
7. Power Up: Turn the circuit breaker back on and start a new cycle to verify that the dishwasher is functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10285180
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error ALL CYCLE AND OPTION LIGHTS FLASHING
Error Code: ALL CYCLE AND OPTION LIGHTS FLASHING Difficulty: Easy

Problem: The cycle has been suspended, usually because the door was opened during operation.

How to Fix ALL CYCLE AND OPTION LIGHTS FLASHING Error (Step-by-Step)
1. Close the Door: This error typically means the cycle was interrupted. Ensure the dishwasher door is firmly closed and latched.
2. Press the Start/Resume Button: Press the ‘Start/Resume’ button one time to continue the cycle from where it left off.
3. Select a New Cycle (If Needed): If pressing ‘Start/Resume’ does not work, press the ‘Cancel’ button to drain the unit. You can then select a new wash cycle.
4. Check for Obstructions: Make sure no dishes are blocking the door from closing properly or interfering with the detergent dispenser.
5. Power Cycle the Dishwasher: If the lights continue to flash, turn off the power to the dishwasher at the circuit breaker for one minute, then turn it back on to reset the control panel.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error ALL CYCLE AND OPTION LIGHTS FLASHING
Error Code: ALL CYCLE AND OPTION LIGHTS FLASHING Difficulty: Easy

Problem: The cycle is suspended because the door was opened.

How to Fix ALL CYCLE AND OPTION LIGHTS FLASHING Error (Step-by-Step)
1. Close the dishwasher door firmly and confirm the error stays cleared during a full test cycle.
2. The dishwasher pauses the cycle when the door is opened mid-cycle.
3. Once the door is securely latched, the cycle will automatically resume.
4. If the cycle does not resume, press the START/RESUME button.
5. Ensure no dishes are blocking the door from closing completely.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error CLEAN LIGHT FLASHING
Error Code: CLEAN LIGHT FLASHING Difficulty: Hard

Problem: Indicates the completion of a wash cycle and that the dishes are clean.

How to Fix CLEAN LIGHT FLASHING Error (Step-by-Step)
1. Disconnect the dishwasher from power at the circuit breaker and confirm the error stays cleared during a full test cycle.
2. Remove the bottom access panel and toe plate by taking out the screws.
3. Inspect the drain pump (W11413393) for any blockages or damage. Replace if necessary.
4. Open the dishwasher door and remove the screws holding the inner door panel to access the main control board (WPW10619006).
5. Carefully disconnect the wire harnesses from the old control board and connect them to the new one.
6. Reassemble the door and restore power to test the dishwasher.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- W11413393
- WPW10619006
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error CLEAN LIGHT FLASHING (7 TIMES)
Error Code: CLEAN LIGHT FLASHING (7 TIMES) Difficulty: Moderate

Problem: Problem with the heating circuit. The dishwasher is not able to heat the water to the required temperature.

How to Fix CLEAN LIGHT FLASHING (7 TIMES) Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker.
2. Remove the lower dish rack to access the heating element at the bottom of the tub.
3. Disconnect the two wires attached to the heating element terminals.
4. Use a multimeter to test the heating element (W10709444) for continuity. A reading of 10-30 ohms is normal. If there is no continuity, the element is faulty.
5. To replace, unscrew the plastic nuts holding the element from underneath the dishwasher tub and install the new one.
6. Locate the high-limit thermostat (W11084153) on the bottom of the tub, disconnect it, and test for continuity. It should have continuity at room temperature. Replace if faulty.
7. Reconnect all components, reassemble the dishwasher, and restore power and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- W11084153
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error CONTROL LOCK LIGHT ON/FLASHING
Error Code: CONTROL LOCK LIGHT ON/FLASHING Difficulty: Easy

Problem: The control panel is locked to prevent unintended use. If a button is pressed while locked, the light will flash.

How to Fix CONTROL LOCK LIGHT ON/FLASHING Error (Step-by-Step)
1. Locate the ‘Control Lock’ or ‘Lock’ button on your dishwasher’s control panel. It may also be a secondary function of another button, often labeled ‘4 HR DELAY’ or similar.
2. Press and hold this button for 3 to 5 seconds.
3. The ‘Control Lock’ light should turn off, indicating the controls are now unlocked.
4. If you press a button while the lock is active, the light will flash to remind you the controls are locked.
5. To re-engage the lock, simply press and hold the same button again for 3-5 seconds until the light turns on.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026