Category: Dishwasher

How to Fix Amana Dishwasher Error F46
Error Code: F46 Difficulty: Moderate

Problem: Inlet Valve Sensor Error. There’s a problem with the inlet valve sensor.

How to Fix F46 Error (Step-by-Step)
1. Shut off both the power and the water supply to the dishwasher.
2. The water inlet valve is typically located at the front, behind the lower kick panel. Remove the screws holding the kick panel in place.
3. You will see the inlet valve with the water supply line and a hose connected to it. Place a towel underneath to catch any water.
4. Disconnect the water supply line and the hose from the valve. You may need pliers for the hose clamp.
5. Disconnect the wiring harness from the old valve and remove the screws that mount it to the dishwasher’s frame.
6. Install the new water inlet valve, making sure to reconnect the wiring harness, water supply line, and hose securely.
7. Turn the water supply back on and check for any leaks before reinstalling the kick panel and restoring power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error F47
Error Code: F47 Difficulty: Hard

Problem: Water Filtration System Issue. The dishwasher’s water filtration system is not operating correctly.

How to Fix F47 Error (Step-by-Step)
1. Disconnect the dishwasher from power and water. Turn off the circuit breaker for the dishwasher and shut off the water supply valve, usually located under the sink.
2. Remove the lower dish rack to access the filter system at the bottom of the dishwasher tub.
3. Twist the upper filter assembly counter-clockwise and lift it out. Then, pull out the lower filter that sits underneath it.
4. Thoroughly clean both filters under running water. Use a soft brush to gently scrub away any food particles or debris. Do not use abrasive materials that could damage the filter mesh.
5. While the filters are removed, inspect the filter housing and the sump area for any foreign objects or blockages. Carefully remove any debris you find.
6. Inspect the drain hose for any kinks, clogs, or damage. Disconnect the hose from the dishwasher and the sink drain to check for obstructions. Clear any blockages you find.
7. Reinstall the clean filters, ensuring they are securely locked in place. Reconnect the drain hose, restore power and water to the dishwasher, and run a short cycle to test the repair.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error F48
Error Code: F48 Difficulty: Moderate

Problem: Drain Hose Blockage. The dishwasher’s drain hose is blocked.

How to Fix F48 Error (Step-by-Step)
1. Disconnect the dishwasher from its power source and confirm the error stays cleared during a full test cycle.
2. The drain hose connects the dishwasher’s drain pump to your sink’s drain or garbage disposal. You will need to access both ends.
3. Place a bucket or towels under the sink connection to catch any water. Disconnect the drain hose from the sink drain or garbage disposal.
4. Check this end of the hose for any blockages and clear them out.
5. To check the entire hose, you may need to pull the dishwasher out slightly to access the connection at the drain pump. Disconnect the hose from the pump.
6. With the hose completely detached, run water through it to flush out any remaining debris. If the hose is damaged or cracked, it should be replaced.
7. Reconnect the drain hose to both the pump and the sink drain, ensuring a secure fit, then restore power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- W11414944
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error F49
Error Code: F49 Difficulty: Easy

Problem: Water Quality Sensor Calibration Error. The calibration of the water quality sensor is incorrect.

How to Fix F49 Error (Step-by-Step)
1. This error often indicates a need to reset and recalibrate the dishwasher’s control board.
2. Start by pressing the ‘Cancel’ button on the dishwasher to stop any ongoing cycle.
3. Turn off the power to the dishwasher at the circuit breaker.
4. Leave the power off for at least 5-10 minutes. This allows the internal electronics to fully reset.
5. Turn the circuit breaker back on to restore power to the dishwasher.
6. Select and run a short wash cycle. This will allow the water quality sensor to recalibrate during the new cycle.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error F50
Error Code: F50 Difficulty: Hard

Problem: Spray Arm Motor Error. The dishwasher’s spray arm motor is malfunctioning.

How to Fix F50 Error (Step-by-Step)
1. Disconnect the dishwasher from the power supply by turning off the circuit breaker.
2. You will need to pull the dishwasher out from under the counter to access the spray arm motor, which is part of the circulation pump assembly located underneath the tub.
3. Lay the dishwasher on its back on a towel or blanket to protect the floor and the appliance.
4. Disconnect the wiring harness and any hoses connected to the circulation pump motor.
5. Remove the mounting screws or clamps that hold the pump and motor assembly in place.
6. Carefully remove the old motor and install the new one, ensuring all seals are properly seated to prevent leaks.
7. Reconnect the hoses and wiring, then carefully set the dishwasher upright, slide it back into place, and restore power to test.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error F7E7
Error Code: F7E7 Difficulty: Hard

Problem: Indicates an issue with the appliance control unit, user interface, or associated wiring.

How to Fix F7E7 Error (Step-by-Step)
1. First, try a simple power reset. Turn off the circuit breaker for the dishwasher for at least 5 minutes.
2. If the error persists, you will need to access the main control unit. Disconnect the power again.
3. The control unit is typically located behind the lower kick panel or inside the door panel. You will need to remove the panel to access it.
4. Carefully inspect all the wiring connections to and from the control unit and user interface. Look for any loose or damaged wires and reconnect or repair them as needed.
5. If all wiring appears secure, the control unit itself is likely faulty and will need to be replaced. Disconnect all wire harnesses from the old board and remove it.
6. Install the new control board, reconnect all wiring harnesses, and reassemble the dishwasher before restoring power.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error FA
Error Code: FA Difficulty: Hard

Problem: The optical water indicator is detecting high levels of water turbidity.

How to Fix FA Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker.
2. Remove the lower dish rack to access the sump area.
3. Locate the optical water indicator (OWI) sensor, which is a small, clear plastic component.
4. Disconnect the wire harness from the sensor and confirm the error stays cleared during a full test cycle.
5. Rotate the sensor counter-clockwise to release it from the sump and pull it out.
6. Install the new OWI sensor by aligning the tabs and turning it clockwise to lock it in place.
7. Reconnect the wire harness and restore power to the dishwasher.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10705575
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 15, 2026
How to Fix Amana Dishwasher Error 1-1
Error Code: 1-1 Difficulty: Hard

Problem: Stuck key detected in keypad or keypad connection.

How to Fix 1-1 Error (Step-by-Step)
1. Disconnect Power: Turn off the circuit breaker or unplug the dishwasher from the wall outlet to ensure your safety.
2. Access the Control Panel: Open the dishwasher door and remove the screws, typically Torx T-15, that hold the inner door panel to the outer door panel.
3. Separate Door Panels: Gently separate the inner and outer door panels to expose the control panel and main control board.
4. Photograph Wiring: Before disconnecting anything, take a clear picture of the wire harness connections to the control board for easy reference during reassembly.
5. Disconnect and Remove Old Part: Carefully unplug the wire harnesses from the control board. Release any clips or screws holding the control panel assembly in place and remove it.
6. Install New Part: Position the new control panel or control board, securing it with the original clips or screws.
7. Reconnect and Reassemble: Using your photo as a guide, reconnect the wire harnesses to the new control board. Rejoin the inner and outer door panels and secure them with the screws.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 2, 2026
How to Fix Amana Dishwasher Error 1-2
Error Code: 1-2 Difficulty: Hard

Problem: Control software issue – damaged or corrupted memory on control board or incompatible software.

How to Fix 1-2 Error (Step-by-Step)
1. Disconnect the dishwasher from power by unplugging it from the wall outlet or shutting off the corresponding circuit breaker in your home’s electrical panel.
2. Open the dishwasher door and remove the screws holding the inner door panel to the outer panel. These are typically located around the perimeter of the inner door.
3. Carefully separate the inner and outer door panels to expose the internal components. The main control board is usually a green circuit board housed in a plastic case, often located at the top or side of the door assembly.
4. Take a clear photo of the wiring connections on the old control board to use as a reference. This will ensure you reconnect everything correctly on the new board.
5. Gently disconnect all wire harnesses attached to the old control board. Most connectors have a small locking tab that needs to be pressed to release the plug.
6. Remove the screws or release the clips holding the old control board in its housing and carefully take it out.
7. Install the new control board, secure it in place, and reconnect all the wire harnesses by referring to the photo you took earlier. Ensure each connector is firmly seated.
8. Reassemble the dishwasher door panels, restore power to the appliance, and run a test cycle to confirm the repair.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 2, 2026
How to Fix Amana Dishwasher Error 2-1
Error Code: 2-1 Difficulty: Hard

Problem: Control software issue – damaged or corrupted memory on control board, or incompatible software.

How to Fix 2-1 Error (Step-by-Step)
1. Disconnect the dishwasher from power by turning off the circuit breaker or unplugging the unit from the wall outlet.
2. Remove the screws securing the inner door panel to the outer door panel. The location and number of screws will vary by model, but they are typically around the perimeter of the inner door.
3. With the screws removed, carefully separate the inner and outer door panels to expose the dishwasher’s internal components. Locate the main control board, which is usually a green circuit board housed in a plastic case.
4. Take a clear photo of the wiring connections on the control board for reference. Carefully disconnect each wire harness from the old control board. Release any locking tabs on the connectors before pulling.
5. Remove the screws or release the plastic tabs holding the old control board in its housing and remove it from the dishwasher.
6. Place the new control board into the housing and secure it with the screws or tabs. Using your photo as a guide, reconnect all the wire harnesses to the correct terminals on the new board, ensuring they click securely into place.
7. Reassemble the dishwasher door by aligning the inner and outer panels and reinstalling all the screws. Restore power to the dishwasher and run a test cycle to ensure the new control board is functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 2, 2026