Category: Dishwasher

How to Fix Amana Dishwasher Error F0E8
Error Code: F0E8 Difficulty: Easy

Problem: Specific error code, meaning not detailed in the provided search results.

How to Fix F0E8 Error (Step-by-Step)
1. Halt the Dishwasher: Press the ‘Cancel’ button to stop the current cycle.
2. Locate the Electrical Panel: Find your home’s circuit breaker box.
3. Switch Off the Breaker: Turn off the circuit breaker that provides electricity to the dishwasher.
4. Perform a Hard Reset: Wait for a minimum of 5 minutes with the power off. This step is crucial for the internal memory to clear.
5. Turn the Power Back On: Flip the breaker back into the ‘ON’ position.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error F0E9
Error Code: F0E9 Difficulty: Hard

Problem: Specific error code, meaning not detailed in the provided search results.

How to Fix F0E9 Error (Step-by-Step)
1. Disconnect Power and Water: For safety, turn off the dishwasher’s circuit breaker in your electrical panel. Also, turn off the hot water supply valve under the sink.
2. Pull Out the Dishwasher: Disconnect the water inlet and drain lines. Remove the two screws securing the dishwasher to the countertop, then carefully slide the unit out.
3. Access the Component: Gently lay the dishwasher on its back on a protective towel. You will see the diverter valve and its motor on the underside of the tub assembly.
4. Remove the Old Part: Unplug the wire connector from the diverter motor. The motor is typically held in place by a mounting bracket or twists to lock. Remove it from the sump assembly.
5. Install the New Diverter Motor: Seat the new motor in place, ensuring the seal is correct, and lock it into position. Reconnect the wire harness securely.
6. Reinstall and Test: Carefully slide the dishwasher back into its space, re-securing it to the countertop. Reconnect the water and drain lines. Turn the power and water back on and run a cycle to check for proper operation and any leaks.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F1E2
Error Code: F1E2 Difficulty: Hard

Problem: Internal board failure.

How to Fix F1E2 Error (Step-by-Step)
1. Turn off the power to the dishwasher at your home’s circuit breaker panel to ensure safety.
2. Remove the lower access panel (kickplate) below the dishwasher door. It is typically held in place by two or four screws.
3. Locate the main control board. It is usually a green circuit board inside a plastic protective case, mounted on the right side behind the kickplate.
4. Take a clear photo of the wire connections to the control board for reference. Carefully disconnect all wire harnesses from the old board by pressing their locking tabs and gently pulling.
5. Remove the screws or release the plastic tabs holding the control board’s case in place and remove the old board from the dishwasher.
6. Install the new control board, securing it in the same position as the old one. Reconnect the wire harnesses to the new board, using the photo you took as a guide to ensure correct placement.
7. Reinstall the lower access panel and its screws. Turn the power back on at the circuit breaker and run a test cycle to ensure the dishwasher is functioning correctly.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F2E3
Error Code: F2E3 Difficulty: Hard

Problem: Indicates an issue with the appliance control unit, user interface or associated wiring.

How to Fix F2E3 Error (Step-by-Step)
1. Turn off the circuit breaker for the dishwasher and confirm the error stays cleared during a full test cycle.
2. Remove the outer door panel by unscrewing the inner door panel screws.
3. Disconnect the wiring harnesses from the control unit and user interface.
4. Replace the faulty component, whether it’s the control unit or user interface.
5. Reconnect all wiring, ensuring a snug fit and confirm the error stays cleared during a full test cycle.
6. Reattach the door panels and restore power and confirm the error stays cleared during a full test cycle.
7. Run a test cycle to confirm the repair and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F2E4
Error Code: F2E4 Difficulty: Moderate

Problem: Indicates an issue with the user interface or associated wiring.

How to Fix F2E4 Error (Step-by-Step)
1. Turn the appliance off to the dishwasher at the circuit breaker.
2. Remove the screws securing the inner door panel and confirm the error stays cleared during a full test cycle.
3. Gently separate the inner and outer door panels to access the user interface.
4. Disconnect the ribbon cable and any other wiring from the user interface board.
5. Remove the old user interface and install the new one.
6. Reconnect all wiring and reassemble the door and confirm the error stays cleared during a full test cycle.
7. Restore power and check if the error is cleared and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F2E5
Error Code: F2E5 Difficulty: Easy

Problem: Specific error code, meaning not detailed in the provided search results.

How to Fix F2E5 Error (Step-by-Step)
1. Press the ‘Cancel’ or ‘Reset’ button on the dishwasher’s control panel.
2. Turn off the dishwasher by pressing the power button and confirm the error stays cleared during a full test cycle.
3. Disconnect the dishwasher from the power source for 5 minutes.
4. Plug the dishwasher back in and turn it on and confirm the error stays cleared during a full test cycle.
5. Select a new wash cycle and press ‘Start’ and confirm the error stays cleared during a full test cycle.
6. If the error persists, repeat the power cycle process and confirm the error stays cleared during a full test cycle.
7. Ensure the dishwasher door is securely latched and confirm the error stays cleared during a full test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F3E5
Error Code: F3E5 Difficulty: Easy

Problem: Indicates an issue with the mini dispenser; detergent should be added manually.

How to Fix F3E5 Error (Step-by-Step)
1. Open the dishwasher door and locate the detergent dispenser and confirm the error stays cleared during a full test cycle.
2. Close the dispenser lid firmly and confirm the error stays cleared during a full test cycle.
3. Select your desired wash cycle and options and confirm the error stays cleared during a full test cycle.
4. Press the ‘Start’ button to begin the cycle and confirm the error stays cleared during a full test cycle.
5. Consider having the mini dispenser checked by a professional if you wish to use it.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F6E4
Error Code: F6E4 Difficulty: Easy

Problem: Indicates an overfill or float-related condition, possibly due to the dishwasher not being level.

How to Fix F6E4 Error (Step-by-Step)
1. Check if the dishwasher is level from front to back and side to side using a level.
2. Adjust the leveling legs at the front and rear of the dishwasher as needed.
3. Ensure the dishwasher is not tilted forward, which can cause water to pool at the front.
4. Clear any debris from the float switch area in the bottom of the tub.
5. Make sure the float moves freely up and down and confirm the error stays cleared during a full test cycle.
6. Run a rinse cycle to check for proper draining and confirm the error stays cleared during a full test cycle.
7. If the issue continues, inspect the drain hose for kinks or clogs.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F7E0
Error Code: F7E0 Difficulty: Hard

Problem: Specific error code, meaning not detailed in the provided search results.

How to Fix F7E0 Error (Step-by-Step)
1. Disconnect the dishwasher from power and confirm the error stays cleared during a full test cycle.
2. Remove the outer door panel to access the latch assembly.
3. Disconnect the wiring to the door latch switches and confirm the error stays cleared during a full test cycle.
4. Remove the screws holding the old latch assembly in place.
5. Install the new door latch assembly and secure it with the screws.
6. Reconnect the wiring harnesses to the new latch and confirm the error stays cleared during a full test cycle.
7. Reassemble the door and restore power to test the dishwasher.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- W10862259
- WPW10130695
- WPW10653840
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026
How to Fix Amana Dishwasher Error F7E4
Error Code: F7E4 Difficulty: Hard

Problem: Indicates a shifter fault.

How to Fix F7E4 Error (Step-by-Step)
1. Turn off power to the dishwasher and confirm the error stays cleared during a full test cycle.
2. Remove the lower access panel and toe kick and confirm the error stays cleared during a full test cycle.
3. Disconnect the hoses and wiring from the circulation pump and confirm the error stays cleared during a full test cycle.
4. Remove the screws or clamps securing the pump to the sump.
5. Carefully remove the old pump and motor assembly and confirm the error stays cleared during a full test cycle.
6. Install the new circulation pump, ensuring a tight seal and confirm the error stays cleared during a full test cycle.
7. Reconnect all hoses and wiring, then reassemble the access panels and restore power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10757216
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
May 31, 2026