Category: Dishwasher

How to Fix Amana Dishwasher Error 2-2
Error Code: 2-2 Difficulty: Hard

Problem: Control detected stuck key(s) in keypad or keypad connection.

How to Fix 2-2 Error (Step-by-Step)
1. Turn off the power to the dishwasher at your home’s circuit breaker panel to ensure safety.
2. Open the dishwasher door and remove the screws holding the inner door panel to the outer door panel. These are typically located around the perimeter of the inner panel.
3. Carefully separate the inner and outer door panels to expose the control panel and its wiring. Take a photo of the wire connections to the control panel for reference.
4. Disconnect the ribbon cable or wire harness that connects the keypad to the main control board. There may be a small locking tab on the connector that needs to be gently released.
5. Remove the screws or release the clips holding the old control panel/keypad assembly in place and carefully remove it from the door.
6. Position the new control panel in the door, secure it with its screws or clips, and reconnect the wire harness to the main control board, using your photo as a guide.
7. Reassemble the inner and outer door panels, secure them with the screws, restore power at the circuit breaker, and run a test cycle to confirm the fix.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 2, 2026
How to Fix Amana Dishwasher Error 5-1
Error Code: 5-1 Difficulty: Moderate

Problem: Door was not latched within 3 seconds of pressing Start/Resume key.

How to Fix 5-1 Error (Step-by-Step)
1. Turn off electrical power to the dishwasher at your home’s circuit breaker or fuse box.
2. Open the dishwasher door and inspect the latch area for any food debris, utensils, or rack obstructions that may prevent it from closing fully.
3. Examine the door strike on the dishwasher tub and the latch assembly on the door for any visible damage or misalignment.
4. To replace the latch, you must remove the screws holding the inner door panel to the outer door.
5. With the inner panel removed, carefully disconnect the wiring harness from the old door latch assembly.
6. Remove the screws holding the old latch in place and install the new one.
7. Reconnect the wiring, reassemble the door panels, and restore power to test the new latch.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10130695
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 2, 2026
How to Fix Amana Dishwasher Error 5-2
Error Code: 5-2 Difficulty: Moderate

Problem: Control programmed to not start if it suspects the door switch is stuck closed.

How to Fix 5-2 Error (Step-by-Step)
1. Disconnect the dishwasher from its power source by turning off the circuit breaker.
2. The door switch is located inside the door panel. You will need to remove the screws around the perimeter of the inner door to separate it from the front panel.
3. Locate the door switch, which is usually near the top by the latch mechanism.
4. Visually inspect the switch for any signs of damage, such as cracks or burn marks.
5. Disconnect the two wires attached to the switch terminals and confirm the error stays cleared during a full test cycle.
6. Use a small screwdriver or nut driver to remove the screws or release the tab holding the old switch in place and install the new switch.
7. Reconnect the wires, reattach the inner door panel, and turn the power back on to test the dishwasher.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10274880
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 2, 2026
How to Fix Amana Dishwasher Error 6-1
Error Code: 6-1 Difficulty: Moderate

Problem: Low/no water (mechanical problem).

How to Fix 6-1 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker.
2. Shut off the hot water supply valve, which is usually under the sink.
3. Check the water supply hose for any kinks or sharp bends that could restrict water flow.
4. Place a bucket or towel under the water inlet valve connection on the dishwasher and disconnect the supply hose to check for clogs.
5. Inspect the small filter screen inside the water inlet valve for any sediment or debris. Clean it gently with a small brush if it’s dirty.
6. If the screen is clean and the hose is clear, the water inlet valve itself may have failed mechanically.
7. To replace it, disconnect the wires and the outlet hose, remove the mounting screws, and install the new valve in the reverse order.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 6-2
Error Code: 6-2 Difficulty: Moderate

Problem: Fill valve electrical problem.

How to Fix 6-2 Error (Step-by-Step)
1. Shut off the dishwasher’s power supply from your home’s fuse box or circuit breaker.
2. Turn off the hot water supply line connected to the dishwasher.
3. Access the water inlet valve, which is typically located at the front bottom of the dishwasher, behind a lower access panel.
4. Carefully disconnect the wiring harness connected to the valve’s solenoids.
5. Inspect the wires and the harness for any signs of burning, corrosion, or loose connections. Reconnect them securely if they appear loose.
6. If the wiring looks good, the electrical solenoid on the valve has likely failed. The entire valve assembly will need to be replaced.
7. Disconnect the water lines, remove the old valve, and install the new one, making sure to reconnect all hoses and wires securely.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 6-3
Error Code: 6-3 Difficulty: Easy

Problem: Suds/air in pump.

How to Fix 6-3 Error (Step-by-Step)
1. Press the ‘Cancel’ or ‘Drain’ button to stop the current cycle and pump out any water and suds.
2. Open the dishwasher door and check if you have used a soap that is not intended for automatic dishwashers, such as liquid dish soap for handwashing. This is the most common cause of excessive suds.
3. If the wrong soap was used, remove the dishes and run a ‘Rinse Only’ or short wash cycle with no detergent to clear out the remaining suds. You may need to do this more than once.
4. Pouring a small amount of vegetable oil (about 1 tablespoon) into the bottom of the dishwasher can also help to break down the suds.
5. Once the suds are gone, you can reload the dishes and start a new cycle using only automatic dishwasher detergent.
6. Ensure you are using the correct amount of detergent as specified by the manufacturer, as using too much can also cause over-sudsing.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 6-4
Error Code: 6-4 Difficulty: Moderate

Problem: Float switch open.

How to Fix 6-4 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker to ensure safety.
2. Open the dishwasher door and remove the bottom dish rack to get access to the tub floor.
3. Locate the float assembly. It looks like a small plastic dome or cylinder in the bottom of the dishwasher tub.
4. Lift the float up and down to see if it moves freely. Sometimes food particles or debris can get stuck underneath, preventing it from dropping down.
5. If the float is stuck, clean around and under it to remove any obstructions.
6. If the float moves freely but the error persists, the float switch underneath it may be faulty. You will need to access this from under the dishwasher.
7. After pulling the dishwasher out, locate the switch directly under the float assembly, disconnect its wiring, and replace it with a new one.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 6-6
Error Code: 6-6 Difficulty: Easy

Problem: Incoming water is too cool.

How to Fix 6-6 Error (Step-by-Step)
1. Before starting a dishwasher cycle, run the hot water at the kitchen sink faucet for a minute or two until the water is hot to the touch.
2. This purges the cold water from the hot water line, ensuring that your dishwasher starts its cycle with hot water immediately.
3. Check the temperature setting on your home’s water heater. For best dishwasher performance, it should be set to at least 120°F (49°C).
4. Avoid running other hot water appliances, like a washing machine or shower, at the same time as the dishwasher to ensure an adequate supply of hot water.
5. If your dishwasher has a ‘High-Temp Wash’ or ‘Sani-Rinse’ option, select it. This uses the dishwasher’s internal heater to boost the water temperature to the required level.
6. If the problem continues, the dishwasher’s internal water heater or thermostat may be malfunctioning, which would require a more technical repair.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Recommended Parts to Check

No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
- Whirlpool dishwasher drain pump
  
  Common replacement category: Drain pump
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.
  
  Search Amazon for Whirlpool dishwasher drain pump
- Whirlpool dishwasher water inlet valve
  
  Common replacement category: Water inlet valve
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.
  
  Search Amazon for Whirlpool dishwasher water inlet valve
- Whirlpool dishwasher control board
  
  Common replacement category: Electronic control board
  
  Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
  
  Why this category can matter: repeating error-code or control faults after wiring and latch checks.
  
  Search Amazon for Whirlpool dishwasher control board
Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 7-1
Error Code: 7-1 Difficulty: Hard

Problem: No heat – heater circuit problem.

How to Fix 7-1 Error (Step-by-Step)
1. Disconnect Power: Turn off the circuit breaker for the dishwasher to ensure safety.
2. Access the Heater: Remove the lower access panel and toe plate at the bottom front of the dishwasher.
3. Disconnect Wires: Locate the heating element terminals at the front of the dishwasher’s tub. Carefully disconnect the two wires attached to it.
4. Remove Old Element: Open the dishwasher door and remove the lower dish rack. Unscrew the plastic nuts holding the old heating element in place from inside the tub.
5. Install New Element: Place the new heating element (Part No. W10518394) into the tub, ensuring the rubber washers are properly seated. Secure it with the nuts from inside the tub.
6. Reconnect and Reassemble: Reconnect the wires to the new element’s terminals. Replace the lower access panel and toe plate.
7. Restore Power: Turn the circuit breaker back on and run a test cycle to confirm the water is heating.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026
How to Fix Amana Dishwasher Error 7-2
Error Code: 7-2 Difficulty: Hard

Problem: Heater stuck on.

How to Fix 7-2 Error (Step-by-Step)
1. Disconnect Power: Completely disconnect the dishwasher from its power source by shutting off the corresponding circuit breaker.
2. Access Control Board: The main control board is usually located inside the dishwasher’s door panel. Remove the screws holding the inner door panel to access it.
3. Disconnect Wiring: Take a clear photo of the wire connections for reference. Carefully disconnect all wire harnesses from the old control board.
4. Remove Old Board: Unclip or unscrew the old control board (Part No. WPW10285180 or W11413274) from its mounting bracket.
5. Install New Board: Mount the new control board in the same position. Reconnect all wire harnesses by referring to the photo you took.
6. Reassemble Door: Secure the inner door panel with the screws you removed earlier.
7. Restore Power: Turn the power back on at the circuit breaker and test the dishwasher’s functions.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher

Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.
1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.
Verified Compatible Alternatives:
- WPW10285180
When It’s Better to Replace Than Repair

Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers

Standard 24-Inch Models

Common under-counter replacement size

Check height, width, and toe-kick clearance

Match hardwire or cord connection requirements

Shop Built-In Dishwashers

Compact Options

18-Inch and Small-Space Models

Useful for narrow cabinets

Confirm ADA or compact dimensions

Verify panel and handle clearance

Compare Compact Dishwashers

Portable and Countertop

No Built-In Cabinet Cutout

Good for rentals or limited cabinets

Confirm faucet adapter compatibility

Measure counter or storage space

View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
June 1, 2026