Author: ApplianceFixGuide Team

  • How to Fix Whirlpool Dishwasher Error E01

    How to Fix Whirlpool Dishwasher Error E01

    Problem: Pump or Diverter Electrical Fault

    How to Fix Dishwasher Error

    1. Turn off power at circuit breaker.
    2. Open dishwasher door fully.
    3. Remove both upper and lower dish racks.
    4. Locate spray arms on upper and lower racks.
    5. Unscrew spray arm caps counterclockwise by hand.
    6. Remove spray arms and soak in hot vinegar solution for 45 minutes.
    7. Use small brush or toothpick to clean all spray holes thoroughly.
    8. Inspect and clean chopper assembly at bottom of tub – remove any food debris.
    9. Check water inlet screen at bottom of tub for clogs.
    10. Reinstall spray arms and secure caps clockwise until tight.
    11. Replace dish racks.
    12. Restore power and run short wash cycle to verify proper water distribution and pressure.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dryer Error Flash-10

    How to Fix Kenmore Dryer Error Flash-10

    Problem: Control system failure – EEPROM error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel and main access covers.
    3. Inspect all control boards for physical damage or burnt components.
    4. Check all wire harness connections for proper seating and corrosion.
    5. Test voltage supply to all control boards.
    6. Attempt to reset by disconnecting power for 20 minutes.
    7. If error persists, document all wire connections before removal.
    8. Replace main control board assembly first.
    9. If error continues, replace user interface board.
    10. Reconnect all harnesses and run complete diagnostic cycle.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error Flash-5

    How to Fix Kenmore Washer Error Flash-5

    Problem: Motor speed control failure – unable to reach proper RPM

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove front access panel.
    3. Inspect drive motor for overheating or unusual smells.
    4. Check motor wiring harness for damage or loose connections.
    5. Test motor windings for proper resistance readings.
    6. Inspect motor speed sensor and connections.
    7. Check drive belt for wear, tension, or damage (if applicable).
    8. If motor control is faulty, replace motor control board assembly.
    9. Verify proper mechanical alignment of all drive components.
    10. Test motor operation at various speeds to verify proper function.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Dishwasher Error F20

    How to Fix Whirlpool Dishwasher Error F20

    Problem: Main Control Board (Power Supply)

    How to Fix Dishwasher Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel cover and lower access panel.
    3. Document all wire connections with photos and written labels.
    4. Disconnect all wire harnesses from both control boards (main and interface).
    5. Remove mounting screws from both boards (8 total).
    6. Carefully remove old boards.
    7. Install new control boards in proper locations, ensuring correct orientation.
    8. Reconnect all wire harnesses exactly as documented – triple-check each connection against photos.
    9. Secure mounting screws to 6 inch-pounds.
    10. Reinstall panels.
    11. Restore power and enter service mode to initialize new boards (press Hi-Temp, Air Dry, Hi-Temp, Air Dry).
    12. Run complete diagnostic cycle and clear error codes.
    13. Test all cycle functions thoroughly with water to verify proper operation.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dishwasher Error F19

    How to Fix Whirlpool Dishwasher Error F19

    Problem: Main Control Board (Internal Logic)

    How to Fix Dishwasher Error

    1. Disconnect power and water supply.
    2. Remove lower access panel and toe kick panel.
    3. Disconnect all water lines and drain hose.
    4. Disconnect all electrical connectors and label them.
    5. Remove 4 mounting screws securing dishwasher to cabinet frame.
    6. Carefully slide dishwasher out from under counter (get helper).
    7. Remove pump/motor assembly mounting bolts (6 bolts).
    8. Disconnect wire harnesses from pump/motor connectors.
    9. Remove old pump/motor assembly.
    10. Clean mounting surface and install new gaskets.
    11. Install new pump/motor assembly and secure mounting bolts to 15 inch-pounds in crisscross pattern.
    12. Reconnect all electrical and water connections.
    13. Slide dishwasher back into position and secure to cabinet.
    14. Restore utilities and test all functions through complete cycle.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Washer Error Flash-4

    How to Fix Kenmore Washer Error Flash-4

    Problem: Temperature sensor failure – incorrect readings

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove lower front access panel.
    3. Locate temperature sensor on tub or heater assembly.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is out of range, remove mounting screw and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Clean sensor mounting area and ensure proper sealing.
    10. Reconnect electrical connector and test temperature readings during cycle.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error Flash-9

    How to Fix Kenmore Dryer Error Flash-9

    Problem: Blower wheel failure – airflow restriction

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Inspect blower wheel for debris, damage, or obstructions.
    4. Check blower wheel mounting and shaft for proper alignment.
    5. Test motor operation independently of blower wheel.
    6. If motor runs but blower wheel doesn’t turn, inspect drive belt.
    7. Remove mounting screws securing blower housing.
    8. Replace damaged blower wheel assembly or drive belt as needed.
    9. Reassemble components and verify proper alignment.
    10. Test airflow and drying performance after repairs.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Dishwasher Error F18

    How to Fix Whirlpool Dishwasher Error F18

    Problem: User Interface Console (Stuck Key)

    How to Fix Dishwasher Error

    1. Turn off power at circuit breaker.
    2. Remove lower access panel.
    3. Locate drain solenoid on side of pump assembly.
    4. Disconnect electrical connector from solenoid.
    5. Remove 2 mounting screws securing solenoid bracket.
    6. Carefully remove old solenoid and plunger assembly.
    7. Clean solenoid mounting surface and plunger shaft with fine sandpaper.
    8. Apply light grease to new plunger shaft.
    9. Install new solenoid assembly with new gasket.
    10. Secure mounting screws to 6 inch-pounds.
    11. Reconnect electrical connector.
    12. Reinstall access panel.
    13. Restore power and test drain cycle, listening for proper solenoid engagement click and complete drainage.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dryer Error Flash-8

    How to Fix Kenmore Dryer Error Flash-8

    Problem: Thermal fuse failure – safety device tripped

    How to Fix Dryer Error

    1. Turn off power supply immediately.
    2. Allow dryer to cool completely.
    3. Remove rear access panel.
    4. Locate thermal fuse on heater housing or blower housing.
    5. Disconnect electrical connector from thermal fuse.
    6. Test thermal fuse continuity with multimeter.
    7. If thermal fuse is open, remove mounting screws and replace fuse.
    8. Inspect high limit thermostat and temperature sensor for proper operation.
    9. Check for airflow restrictions causing overheating.
    10. Restore power and test heating cycle with temperature monitoring.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error Flash-3

    How to Fix Kenmore Washer Error Flash-3

    Problem: Drain pump failure – water not draining properly

    How to Fix Washer Error

    1. Turn off power supply.
    2. Remove lower front access panel.
    3. Check drain hose for kinks, blockages, or improper routing.
    4. Remove drain pump access cover and clean debris from filter.
    5. Inspect drain pump impeller for damage or obstructions.
    6. Test drain pump motor resistance with multimeter.
    7. Check drain pump wiring for corrosion or damage.
    8. If pump is weak or clogged, disconnect electrical connector and hoses.
    9. Remove mounting screws and replace drain pump assembly.
    10. Test drain cycle timing and verify complete drainage.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes