Author: ApplianceFixGuide Team

  • How to Fix Kenmore Dishwasher Error All LEDs on simultaneously

    How to Fix Kenmore Dishwasher Error All LEDs on simultaneously

    Problem: Diagnostic test mode active

    How to Fix All LEDs on simultaneously Error

    1. This indicates the dishwasher has entered Service Diagnostic Mode.
    2. Press ‘Cancel’ or open and close the door to exit.
    3. If it won’t exit, unplug the dishwasher for 1 minute to reset.

    What to Check Next on This Kenmore Dishwasher

    Kenmore Dishwasher Error All LEDs on simultaneously: Use the code or symptom as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. Turn power off before opening panels, reaching into the sump, or checking the valve, pump, heater, latch, sensor, or control wiring.
    2. Clean the filter and sump, check spray-arm movement, verify water supply, and inspect the drain hose and sink connection first.
    3. Confirm whether the fault appears during fill, wash, drain, heat/dry, latch, leak detection, or control-panel response.
    4. Run a short test cycle after cleaning and watch the exact stage where the symptom returns.
    5. Replace a part only after the same fault repeats and the complete Kenmore dishwasher model number confirms the right component.

    If the issue returns after these checks, match replacement parts to the complete Kenmore dishwasher model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Kenmore dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Kenmore dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after filter, sump, and hose checks.

      Search Amazon for Kenmore dishwasher drain pump

    • Kenmore dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill faults after supply, float, and inlet screen checks.

      Search Amazon for Kenmore dishwasher water inlet valve

    • Kenmore dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by complete Kenmore dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for weak wash or spray-arm symptoms after filter and spray-arm checks.

      Search Amazon for Kenmore dishwasher circulation pump

    Before ordering: match the part to the complete Kenmore dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Samsung Washer Error C6

    How to Fix Samsung Washer Error C6

    Problem: Calibration mode active

    How to Fix C6 Error

    1. This is not an error code, but an information code indicating the washer is in calibration mode.
    2. Calibration mode is a necessary process that allows the washer to learn the weight of the drum and optimize spin performance. It should be run after installation or any significant repair.
    3. Do not interrupt the process. Allow the washer to complete the calibration cycle, which typically takes a few minutes. The drum will rotate back and forth at various speeds.
    4. Once complete, the display will show ‘End’ or return to a normal state, and the washer will be ready for regular use.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You

    Browse all Samsung error codes: Samsung Error Codes

    Best Value Replacement Washers

    If your current unit is repeatedly failing, replacing it may save money versus another major repair.

    Budget Option ($200-$600)

    Top Rated Full Size Models Under $600

    Check Price & Delivery on Amazon

    Mid-Range Option ($600-$1000)

    Best-Selling Full Size Washers

    Check Price & Delivery on Amazon

    Premium Option ($1000+)

    Premium Full Size Washers

    Check Price & Delivery on Amazon

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Samsung Dishwasher Error AP

    How to Fix Samsung Dishwasher Error AP

    Problem: Access Point mode for mobile/Wi-Fi connection

    How to Fix AP Error

    1. UNDERSTAND THE MODE. ‘AP’ stands for Access Point mode. The dishwasher is broadcasting its own Wi-Fi signal so you can connect your smartphone to it for initial setup with the SmartThings app.
    2. CONNECT YOUR PHONE. On your smartphone, go to Wi-Fi settings and look for a network named ‘[dishwasher] Samsung’ or similar. Connect to this network.
    3. COMPLETE SETUP IN THE APP. Open the Samsung SmartThings app and follow the on-screen instructions to add the dishwasher to your home Wi-Fi network. The ‘AP’ code will disappear once the connection is successful.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dishwasher Error 1C

    How to Fix Samsung Dishwasher Error 1C

    Problem: Filter clogged / Load or detergent issue

    How to Fix 1C Error

    1. CLEAN THE FILTERS. This code often indicates a clogged filter. Open the dishwasher and remove the lower rack. Twist and lift out the main filter assembly from the bottom of the tub.
    2. WASH THE FILTERS. Separate the cylindrical micro-filter from the coarse filter plate. Wash both thoroughly under warm running water using a soft brush to remove food particles and grease.
    3. REINSTALL AND TEST. Reassemble the filter components and lock them back into place in the dishwasher. Run a new cycle. If the code returns, use less detergent and ensure dishes are not blocking the spray arms.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Whirlpool Dryer Error L2

    How to Fix Whirlpool Dryer Error L2

    Problem: Low or No Line Voltage on L2 leg

    How to Fix L2 Error

    1. Check your home circuit breaker box; the dryer requires two fuses/breakers to provide 240V.
    2. Reset the breakers even if they look on (flip Off then On).
    3. If the dryer runs but doesn’t heat, verify the power cord terminal block screws are tight.

    What to Check Next on This Whirlpool Dryer

    Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check.

    1. Disconnect power before panel inspection, then verify the lint screen, exterior vent hood, and full vent run are clear.
    2. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path.
    3. For heat-related faults, check airflow first, then inspect the thermal fuse, thermistor, heater or gas ignition path, wiring, and control output.
    4. For motor or control faults, listen for hums or relay clicks and inspect the belt, door switch, motor harness, and board connectors.
    5. Order parts only after matching the complete Whirlpool dryer model number, since sensors, fuses, elements, and controls vary by platform.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Whirlpool model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Whirlpool dryer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dryer thermal fuse
      Common replacement category: Thermal fuse
      Fit note: Exact OEM part number varies by complete Whirlpool dryer model number. Confirm compatibility before buying.
      Why this category can matter: no-heat or no-start symptoms after venting and power checks.

      Search Amazon for Whirlpool dryer thermal fuse

    • Whirlpool dryer heating element
      Common replacement category: Heating element
      Fit note: Exact OEM part number varies by complete Whirlpool dryer model number. Confirm compatibility before buying.
      Why this category can matter: electric dryer no-heat symptoms after airflow checks.

      Search Amazon for Whirlpool dryer heating element

    • Whirlpool dryer control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Whirlpool dryer model number. Confirm compatibility before buying.
      Why this category can matter: cycle-control or repeated electronic faults after wiring checks.

      Search Amazon for Whirlpool dryer control board

    Before ordering: match the part to the complete Whirlpool dryer model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Samsung Refrigerator Error 11C

    How to Fix Samsung Refrigerator Error 11C

    Problem: Flex room defrost sensor error – alias of 11E

    How to Fix 11C Error

    1. Unplug the refrigerator and remove the drawers from the Flex Zone/Cool Select area.
    2. Remove the rear interior panel to access the evaporator coil.
    3. Locate the sensor clipped to the coil, disconnect the harness, and clip the new sensor in the exact same location.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error 11E

    How to Fix Samsung Refrigerator Error 11E

    Problem: Flex room / Cool Select Zone defrost sensor error

    How to Fix 11E Error

    1. Unplug the refrigerator. Remove the Flex Zone drawers and back panel.
    2. Test the sensor resistance with a multimeter (should be approx 5k-10k ohms at room temp).
    3. If open/shorted, replace the sensor. Secure it tightly to the refrigerant line with a zip tie.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error 13E

    How to Fix Samsung Refrigerator Error 13E

    Problem: Humidity sensor error

    How to Fix 13E Error

    1. Unplug the refrigerator.
    2. Locate the humidity sensor (usually in the mullion bar between doors or near the crisper).
    3. Inspect wiring for corrosion. If wiring is clean, replace the humidity sensor module.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error 14C

    How to Fix Samsung Refrigerator Error 14C

    Problem: Ice maker sensor error – alias of 14E

    How to Fix 14C Error

    1. Unplug the refrigerator or turn off the ice maker.
    2. This sensor is embedded in the Ice Maker assembly and is not sold separately.
    3. Remove the ice bucket, unscrew the Ice Maker unit, disconnect the wire harness, and install the new assembly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Refrigerator Error 21C

    How to Fix Samsung Refrigerator Error 21C

    Problem: Freezer evaporator fan error – alias of 21E

    How to Fix 21C Error

    1. Unplug the refrigerator and remove all freezer baskets/shelves.
    2. Remove the rear evaporator cover panel.
    3. Check if ice is blocking the fan. If ice is present, defrost the drain. If clear, replace the fan motor.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Samsung error codes: Samsung Error Codes