Author: ApplianceFixGuide Team

  • How to Fix Whirlpool Washer Error F01

    How to Fix Whirlpool Washer Error F01

    Problem: EEPROM communication failure on main control board or motor control module fault

    How to Fix Washer Error

    1. Unplug washer for 5 minutes to reset electronics.
    2. Inspect all wire harness connections at main control board (CCU) and motor control unit (MCU), especially the 3-wire serial communication harness (white connector with blue wires).
    3. Verify connections are fully seated and not corroded.
    4. Check for burnt components or moisture damage on control boards.
    5. If connections are secure and code returns after reset, replace main control board (CCU) W
    6. After replacement, run diagnostic cycle to verify communication between CCU and MCU.
    7. If F01 persists after CCU replacement, replace motor control unit (MCU) W

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F04

    How to Fix Whirlpool Dryer Error F04

    Problem: Airflow restriction or heating element issue.

    How to Fix Dryer Error

    1. Clean the lint screen.
    2. Check the exhaust vent for clogs.
    3. If clear, test the heating element for continuity.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F03

    How to Fix Whirlpool Dryer Error F03

    Problem: Outlet Thermistor Open/Short

    How to Fix Dryer Error

    1. Unplug dryer.
    2. Check wiring to the exhaust thermistor.
    3. Measure resistance (should be ~10k ohms at room temp).
    4. Replace thermistor if bad.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F02

    How to Fix Whirlpool Dryer Error F02

    Problem: Keypad/User Interface Failure

    How to Fix Dryer Error

    1. Check for stuck buttons.
    2. Unplug dryer for 1 minute.
    3. If error persists, replace the user interface assembly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dryer Error F01

    How to Fix Whirlpool Dryer Error F01

    Problem: Primary Control Failure

    How to Fix Dryer Error

    1. Unplug the dryer for 5 minutes.
    2. Restore power.
    3. If error returns, replace the main electronic control board.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Washer Error Power-Failure

    How to Fix Kenmore Washer Error Power-Failure

    Problem: Electrical power interruption during cycle

    How to Fix Washer Error

    1. Check household circuit breaker for tripped condition.
    2. Verify power outlet is functioning with another appliance.
    3. Inspect power cord for damage or loose connections.
    4. Check washer poer cord connection at terminal block inside machine.
    5. Test voltage at terminal block with multimeter (should read 120V).
    6. If power was restored, press START/PAUSE button to resume cycle.
    7. If cycle won’t restart, disconnect power for 5 minutes to reset control boards.
    8. Check for blown fuses on control boards if accessible.
    9. Inspect main power supply wiring for damage or corrosion.
    10. Test washer operation after power restoration and reset procedures.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error Flash-12

    How to Fix Kenmore Dryer Error Flash-12

    Problem: Lint filter reminder – maintenance required

    How to Fix Dryer Error

    1. Turn off power supply and allow dryer to cool.
    2. Remove lint filter from housing.
    3. Clean lint filter thoroughly under warm running water with mild soap.
    4. Use soft brush to remove embedded lint and debris.
    5. Rinse filter completely and allow to dry completely.
    6. Inspect lint filter housing for accumulated lint and debris.
    7. Clean housing with vacuum cleaner and soft brush.
    8. Reinstall clean lint filter ensuring proper seating.
    9. Reset lint filter reminder through control panel if available.
    10. Test dryer operation and monitor for proper airflow.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Dishwasher Error E02

    How to Fix Whirlpool Dishwasher Error E02

    Problem: Flow Meter / Inlet System Electrical Fault

    How to Fix Dishwasher Error

    1. Disconnect power at circuit breaker.
    2. Turn off water supply valve under sink.
    3. Remove lower access panel.
    4. Place towels under drain area.
    5. Disconnect drain hose from pump outlet.
    6. Remove drain filter cover by turning counterclockwise.
    7. Lift out drain filter and clean thoroughly under running water.
    8. Inspect drain pump impeller – insert finger to check for free rotation and removeany debris.
    9. Check entire drain hose path for kinks or blockages – straighten or replace hose if needed.
    10. Reinstall drain filter and secure cover clockwise until tight.
    11. Reconnect drain hose with new hose clamp.
    12. Restore water and power.
    13. Test drain cycle and listen for proper pump operation – should drain completely in 90 seconds.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Washer Error Unbalanced

    How to Fix Kenmore Washer Error Unbalanced

    Problem: Load imbalance detected during spin cycle

    How to Fix Washer Error

    1. Pause the wash cycle immediately.
    2. Open washer door/lid and redistribute laundry evenly around drum.
    3. Remove any large, heavy items that may cause imbalance.
    4. Add a few smaller items to help balance the load if needed.
    5. Close door/lid and restart the spin cycle.
    6. If imbalance persists, reduce spin speed setting for this load.
    7. Check washer leveling by adjusting feet until bubble level shows level.
    8. Ensure all four feet are firmly on floor and not rocking.
    9. For future loads, distribute items of similar weight evenly around drum.
    10. Test with balanced load to verify proper spin operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Dryer Error Flash-11

    How to Fix Kenmore Dryer Error Flash-11

    Problem: User interface failure – display or keypad error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel faceplate and access cover.
    3. Inspect user interface board connectors for corrosion or damage.
    4. Check ribbon cable connections between interface and main control.
    5. Test communication signals with multimeter if possible.
    6. Clean all electrical contacts with contact cleaner.
    7. If connections are good but error persists, replace user interface board.
    8. Document all wire connections before disconnecting.
    9. Install new user interface board assembly.
    10. Test all button functions and display operation.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes