Author: ApplianceFixGuide Team

  • How to Fix Whirlpool Dishwasher Error F17

    How to Fix Whirlpool Dishwasher Error F17

    Problem: Main Control Board (Memory/EEPROM)

    How to Fix Dishwasher Error

    1. Disconnect power at circuit breaker.
    2. Remove lower access panel.
    3. Locate diverter motor on top of circulation pump housing.
    4. Disconnect electrical connector from motor.
    5. Remove 3 mounting screws securing motor assembly.
    6. Carefully lift motor assembly off pump housing.
    7. Clean drive mechanism and check for binding in gears.
    8. Install new diverter motor assembly with new gasket.
    9. Secure mounting screws to 7 inch-pounds in sequence.
    10. Reconnect electrical connector.
    11. Reinstall access panel.
    12. Restore power and test upper/lower spray arm operation during wash cycle – should alternate properly between arms.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dryer Error Flash-7

    How to Fix Kenmore Dryer Error Flash-7

    Problem: High limit thermostat failure – safety shutdown

    How to Fix Dryer Error

    1. Turn off power supply immediately.
    2. Allow dryer to cool completely.
    3. Remove rear access panel.
    4. Locate high limit thermostat on heater housing.
    5. Disconnect electrical connector from thermostat.
    6. Test thermostat continuity with multimeter.
    7. If thermostat is open, remove mounting screws and replace thermostat.
    8. Inspect heater element for short circuits or grounding issues.
    9. Check wiring harness for damage or corrosion.
    10. Restore power and test heating cycle with temperature monitoring.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error Flash-2

    How to Fix Kenmore Washer Error Flash-2

    Problem: Water inlet valve failure – no water entering

    How to Fix Washer Error

    1. Turn off power and check household water supply valves.
    2. Verify water pressure at supply lines (minimum 20 PSI required).
    3. Remove lower front access panel.
    4. Inspect water inlet valve screens for debris or mineral buildup.
    5. Clean inlet valve filter screens with vinegar solution.
    6. Test inlet valve solenoids with multimeter for proper resistance.
    7. If valve is faulty, disconnect water supply lines and electrical connector.
    8. Remove mounting screws and replace water inlet valve assembly.
    9. Restore water and power connections.
    10. Test fill cycle operation and timing.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Dishwasher Error F16

    How to Fix Whirlpool Dishwasher Error F16

    Problem: Main Control Board (Processor Check)

    How to Fix Dishwasher Error

    1. Turn off power at circuit breaker.
    2. Open dishwasher door fully.
    3. Remove lower dish rack.
    4. Locate spray arm assembly on bottom of tub.
    5. Unscrew spray arm cap counterclockwise by hand.
    6. Lift out spray arm and soak in vinegar solution for 30 minutes.
    7. Clean all spray holes with toothpick or small brush to remove mineral deposits.
    8. Inspect chopper blade for damage or debris – clean thoroughly.
    9. Check filter screen around spray arm base for clogs.
    10. Reinstall spray arm and secure cap clockwise until tight.
    11. Replace lower rack.
    12. Restore power and test wash cycle, observing water spray pattern for proper coverage.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dryer Error Flash-6

    How to Fix Kenmore Dryer Error Flash-6

    Problem: Door switch failure – door open circuit

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Open dryer door fully.
    3. Inspect door switch mechanism for proper alignment.
    4. Test door switch continuity with multimeter.
    5. Check door strike plate alignment with switch mechanism.
    6. Inspect door switch wiring for damage or loose connections.
    7. If door switch is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace door switch assembly.
    9. Ensure proper alignment during installation.
    10. Test door closure and cycle operation.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Kenmore Washer Error Flash-1

    How to Fix Kenmore Washer Error Flash-1

    Problem: Unknown

    How to Fix Washer Error

    Consult manual.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Dishwasher Error F15

    How to Fix Whirlpool Dishwasher Error F15

    Problem: Motor Control Unit (MCU) / Main Board Communication

    How to Fix Dishwasher Error

    1. Disconnect power at circuit breaker.
    2. Remove lower access panel and toe kick panel.
    3. Take photos of all wire connections to main control board.
    4. Disconnect all wire harness connectors (label each one).
    5. Remove 4 mounting screws securing control board.
    6. Carefully remove old control board.
    7. Install new control board, ensuring proper orientation.
    8. Reconnect all wire harnesses exactly as documented – double-check each connection.
    9. Secure mounting screws to 8 inch-pounds.
    10. Reinstall panels.
    11. Restore power and enter service mode to initialize new board (press Heated Dry, Normal, Heated Dry, Normal).
    12. Run complete diagnostic cycle and clear any stored error codes.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Kenmore Dryer Error Flash-5

    How to Fix Kenmore Dryer Error Flash-5

    Problem: Control board failure – main PCB error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel access cover.
    3. Inspect main control board for burnt components or damaged traces.
    4. Check all wire harness connections for proper seating and corrosion.
    5. Test voltage supply to control board.
    6. If board shows physical damage, document all wire connections.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new main control board assembly.
    9. Reconnect all harnesses in correct positions.
    10. Power up and run diagnostic cycle to verify operation.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Whirlpool Dishwasher Error F14

    How to Fix Whirlpool Dishwasher Error F14

    Problem: Main Control Board / VS Motor Electronics

    How to Fix Dishwasher Error

    1. Disconnect power and water supply.
    2. Remove lower access panel.
    3. Locate flow meter in water supply line near inlet valve.
    4. Turn off household water supply valve.
    5. Place towels under flow meter to catch residual water.
    6. Disconnect water lines from flow meter using adjustable wrenches.
    7. Disconnect electrical connector.
    8. Remove mounting bracket securing flow meter.
    9. Install new flow meter with new O-rings lubricated with silicone grease.
    10. Reconnect water lines (hand-tight plus quarter turn).
    11. Reconnect electrical connector.
    12. Turn on water slowly and check for leaks.
    13. Restore power and test fill cycle while monitoring for proper water flow detection.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes

  • How to Fix Whirlpool Dishwasher Error F13

    How to Fix Whirlpool Dishwasher Error F13

    Problem: Dispenser Unit Failure / Control Board

    How to Fix Dishwasher Error

    1. Turn off power at circuit breaker.
    2. Remove lower access panel.
    3. Locate pressure switch on side wall of dishwasher.
    4. Disconnect electrical connector and air tube from switch.
    5. Remove 2 mounting screws securing switch.
    6. Clean air tube with compressed air to remove moisture and debris.
    7. Install new pressure switch and secure mounting screws.
    8. Reconnect air tube ensuring tight fit (no leaks).
    9. Reconnect electrical connector.
    10. Reinstall access panel.
    11. Restore power and test fill cycle, listening for proper water level detection sounds.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Whirlpool error codes: Whirlpool Error Codes