Author: ApplianceFixGuide Team

  • How to Fix GE Dryer Error Do

    How to Fix GE Dryer Error Do

    Problem: Door Open – alias of dE; door not closed

    How to Fix Do Error

    1. This is an alias for the ‘dE’ (Door Error) code. First, open the door and close it firmly.
    2. If the code persists, the door switch has failed. UNPLUG THE DRYER.
    3. Access the door switch by removing the top or front panel. It’s located in the frame where the door closes.
    4. Disconnect the wiring and use a multimeter to test the switch for continuity when its plunger is pressed. If it fails the test, it needs to be replaced.
    5. Install the new switch, reconnect the wiring, and reassemble the dryer.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error Draining Cancelled

    How to Fix GE Dryer Error Draining Cancelled

    Problem: Draining was cancelled – combo unit paused too long

    How to Fix Draining Cancelled Error

    1. This message appears on washer/dryer combo units.
    2. It means the unit was paused for too long (typically more than 15-20 minutes), and the machine cancelled the operation for safety.
    3. To resolve, simply press the ‘Start/Pause’ button to resume the cycle from where it left off.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E01

    How to Fix GE Dryer Error E01

    Problem: Main control board / internal error – EEPROM or board failure

    How to Fix E01 Error

    1. UNPLUG THE DRYER. This error indicates a critical failure of the main control board (EEPROM error).
    2. First, try a hard reset. Leave the dryer unplugged for at least 10 minutes, then plug it back in. If the error returns, the board must be replaced.
    3. The main control board is typically located inside the control console or on a side wall of the cabinet. Accessing it requires significant disassembly.
    4. Take a photo of the board for reference. Carefully label every wire harness with masking tape before disconnecting it from the old board.
    5. Disconnect all harnesses, remove the mounting screws, and swap the old board with the new one. Meticulously reconnect every wire harness to its correct location on the new board. Reassemble and test.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E12

    How to Fix GE Dryer Error E12

    Problem: Heater relay failure – relay on control board stuck closed

    How to Fix E12 Error

    1. UNPLUG THE DRYER IMMEDIATELY. This error means the heater relay on the main control board is stuck in the closed (on) position, which is a serious fire hazard.
    2. The relay is a non-serviceable part of the main control board.
    3. The only safe and correct repair is to replace the entire main control board.
    4. Follow the procedure for code F01: Locate the board, photograph the wiring, label and disconnect all harnesses, swap the board, and carefully reconnect all wires.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E13

    How to Fix GE Dryer Error E13

    Problem: Moisture sensor failure – moisture sensor not reading properly

    How to Fix E13 Error

    1. UNPLUG THE DRYER. This error indicates a problem with the moisture sensor system.
    2. Locate the two metal sensor bars inside the dryer drum, usually near the lint filter housing.
    3. Vigorously clean the surface of both metal bars with a cloth or pad dampened with rubbing alcohol. Fabric softener residue can coat the bars and prevent them from sensing moisture.
    4. If cleaning does not resolve the issue, inspect the wires leading from the sensor bars to the main control board for breaks. If the wires are good, the sensor bars themselves may need to be replaced (a ‘Moderate’ difficulty repair).

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E14

    How to Fix GE Dryer Error E14

    Problem: Gas valve failure – gas valve solenoid failing to open (gas dryers)

    How to Fix E14 Error

    1. UNPLUG THE DRYER and SHUT OFF THE GAS SUPPLY VALVE. This is for gas dryers only.
    2. First, confirm the gas supply valve behind the dryer is fully open. If it is, proceed with the repair.
    3. Remove the dryer’s front panel to access the burner assembly. The gas valve with the solenoids will be visible.
    4. Disconnect the wires from the solenoids. They are typically held on by a simple bracket. Remove the bracket and lift the old solenoids off.
    5. Install the new solenoids from the kit, re-secure the bracket, and reconnect the wires. Reassemble, turn the gas back on, and check for leaks with soapy water before plugging in and testing.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E15

    How to Fix GE Dryer Error E15

    Problem: Door switch failure – door switch not registering properly

    How to Fix E15 Error

    1. UNPLUG THE DRYER. This is a direct failure code for the door switch.
    2. Follow the same procedure as for code ‘dE’. Access the switch by removing the top or front panel.
    3. Disconnect the wiring and use a multimeter to confirm the switch is faulty (it should only have continuity when its button is physically pressed).
    4. Remove the old switch and install the new one. Reconnect the wiring and reassemble the dryer.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E16

    How to Fix GE Dryer Error E16

    Problem: Stuck button/key – button continuously pressed >30 seconds

    How to Fix E16 Error

    1. UNPLUG THE DRYER. This is an alias for code ‘006’, indicating a button on the user interface (UI) is stuck.
    2. Try gently pressing and releasing each button on the control panel to free the stuck one.
    3. If the error persists, the UI board is faulty and must be replaced.
    4. Access the board by removing the control console. Disconnect the wiring from the old board, remove it, and install the new one. Reconnect the wiring and reassemble.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E18

    How to Fix GE Dryer Error E18

    Problem: Communication error – main control and UI board not communicating

    How to Fix E18 Error

    1. UNPLUG THE DRYER. This indicates a communication failure between the main control board and the user interface (UI) board.
    2. Access the control area and locate both boards. Carefully inspect the ribbon cable and any other wiring that connects the two boards. Reseat the connectors firmly at both ends.
    3. If the wiring is intact and the error persists, one of the two boards has failed. It can be difficult to determine which one without specialized tools.
    4. As a general rule, the main control board (WE22X
    5. is the more common point of failure. Replacing it is the first logical step. If that fails, replace the UI board (WE19M
    6. .

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes

  • How to Fix GE Dryer Error E26

    How to Fix GE Dryer Error E26

    Problem: Gas flame failure – igniter lights but flame does not establish (gas dryers)

    How to Fix E26 Error

    1. UNPLUG THE DRYER and SHUT OFF THE GAS SUPPLY. This is a gas flame failure error.
    2. Remove the front panel to access the burner assembly. The three main components to check are the igniter, flame sensor, and gas valve solenoids.
    3. Test the igniter for continuity; if it’s open, it’s bad. Test the flame sensor for continuity; it should be a closed circuit. Test the gas valve solenoids for resistance; if any are open, they are bad.
    4. The most common failure is a weak igniter that glows but doesn’t get hot enough to open the gas valve. Replacing the igniter is the first step. If that fails, replace the flame sensor, and finally the gas valve solenoids.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Ge error codes: Ge Error Codes