Category: Kenmore

  • How to Fix Kenmore Refrigerator Error DE

    How to Fix Kenmore Refrigerator Error DE

    Problem: Defrost system error – extended defrost cycle detected

    How to Fix Refrigerator Error

    1. UNPLUG unit and manually defrost until all ice melts from evaporator coils.
    2. Remove evaporator cover panel in freezer.
    3. Test defrost heater for continuity (should read 20-50 ohms).
    4. Test defrost thermostat when cold (should read closed).
    5. Test defrost timer/adaptive control operation (should advance to defrost mode every 8-12 hours compressor run time).
    6. Replace faulty component causing incomplete defrost (heater most common).
    7. Clean evaporator coils thoroughly after defrosting.
    8. Monitor for 3 complete defrost cycles to verify heater activates and terminates properly without triggering DE code again.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Refrigerator Error 6 BLINK

    How to Fix Kenmore Refrigerator Error 6 BLINK

    Problem: Compressor overload or start system failure (795 series flash code)

    How to Fix Refrigerator Error

    1. UNPLUG unit for 30 minutes to allow compressor thermal overload to reset.
    2. Restore power and listen for compressor attempting to start (brief hum then shutdown indicates overload).
    3. Remove rear access panel to access compressor.
    4. Replace start relay/overload kit first (least expensive component).
    5. If compressor still won’t start, test compressor windings for shorts/opens (requires multimeter).
    6. If windings good but compressor locked (won’t rotate shaft with screwdriver), install hard start booster capacitor as temporary fix.
    7. If windings shorted or compressor seized permanently, requires sealed system repair by licensed technician (refrigerant handling required).
    8. NEVER operate compressor with hard start device for >30 days – causes permanent damage.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error Power-Failure

    How to Fix Kenmore Washer Error Power-Failure

    Problem: Electrical power interruption during cycle

    How to Fix Washer Error

    1. Check household circuit breaker for tripped condition.
    2. Verify power outlet is functioning with another appliance.
    3. Inspect power cord for damage or loose connections.
    4. Check washer poer cord connection at terminal block inside machine.
    5. Test voltage at terminal block with multimeter (should read 120V).
    6. If power was restored, press START/PAUSE button to resume cycle.
    7. If cycle won’t restart, disconnect power for 5 minutes to reset control boards.
    8. Check for blown fuses on control boards if accessible.
    9. Inspect main power supply wiring for damage or corrosion.
    10. Test washer operation after power restoration and reset procedures.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error Flash-12

    How to Fix Kenmore Dryer Error Flash-12

    Problem: Lint filter reminder – maintenance required

    How to Fix Dryer Error

    1. Turn off power supply and allow dryer to cool.
    2. Remove lint filter from housing.
    3. Clean lint filter thoroughly under warm running water with mild soap.
    4. Use soft brush to remove embedded lint and debris.
    5. Rinse filter completely and allow to dry completely.
    6. Inspect lint filter housing for accumulated lint and debris.
    7. Clean housing with vacuum cleaner and soft brush.
    8. Reinstall clean lint filter ensuring proper seating.
    9. Reset lint filter reminder through control panel if available.
    10. Test dryer operation and monitor for proper airflow.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error Unbalanced

    How to Fix Kenmore Washer Error Unbalanced

    Problem: Load imbalance detected during spin cycle

    How to Fix Washer Error

    1. Pause the wash cycle immediately.
    2. Open washer door/lid and redistribute laundry evenly around drum.
    3. Remove any large, heavy items that may cause imbalance.
    4. Add a few smaller items to help balance the load if needed.
    5. Close door/lid and restart the spin cycle.
    6. If imbalance persists, reduce spin speed setting for this load.
    7. Check washer leveling by adjusting feet until bubble level shows level.
    8. Ensure all four feet are firmly on floor and not rocking.
    9. For future loads, distribute items of similar weight evenly around drum.
    10. Test with balanced load to verify proper spin operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error Flash-11

    How to Fix Kenmore Dryer Error Flash-11

    Problem: User interface failure – display or keypad error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel faceplate and access cover.
    3. Inspect user interface board connectors for corrosion or damage.
    4. Check ribbon cable connections between interface and main control.
    5. Test communication signals with multimeter if possible.
    6. Clean all electrical contacts with contact cleaner.
    7. If connections are good but error persists, replace user interface board.
    8. Document all wire connections before disconnecting.
    9. Install new user interface board assembly.
    10. Test all button functions and display operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error Flash-10

    How to Fix Kenmore Dryer Error Flash-10

    Problem: Control system failure – EEPROM error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel and main access covers.
    3. Inspect all control boards for physical damage or burnt components.
    4. Check all wire harness connections for proper seating and corrosion.
    5. Test voltage supply to all control boards.
    6. Attempt to reset by disconnecting power for 20 minutes.
    7. If error persists, document all wire connections before removal.
    8. Replace main control board assembly first.
    9. If error continues, replace user interface board.
    10. Reconnect all harnesses and run complete diagnostic cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error Flash-5

    How to Fix Kenmore Washer Error Flash-5

    Problem: Motor speed control failure – unable to reach proper RPM

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove front access panel.
    3. Inspect drive motor for overheating or unusual smells.
    4. Check motor wiring harness for damage or loose connections.
    5. Test motor windings for proper resistance readings.
    6. Inspect motor speed sensor and connections.
    7. Check drive belt for wear, tension, or damage (if applicable).
    8. If motor control is faulty, replace motor control board assembly.
    9. Verify proper mechanical alignment of all drive components.
    10. Test motor operation at various speeds to verify proper function.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error Flash-4

    How to Fix Kenmore Washer Error Flash-4

    Problem: Temperature sensor failure – incorrect readings

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove lower front access panel.
    3. Locate temperature sensor on tub or heater assembly.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications chart.
    7. If sensor is out of range, remove mounting screw and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Clean sensor mounting area and ensure proper sealing.
    10. Reconnect electrical connector and test temperature readings during cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error Flash-9

    How to Fix Kenmore Dryer Error Flash-9

    Problem: Blower wheel failure – airflow restriction

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Inspect blower wheel for debris, damage, or obstructions.
    4. Check blower wheel mounting and shaft for proper alignment.
    5. Test motor operation independently of blower wheel.
    6. If motor runs but blower wheel doesn’t turn, inspect drive belt.
    7. Remove mounting screws securing blower housing.
    8. Replace damaged blower wheel assembly or drive belt as needed.
    9. Reassemble components and verify proper alignment.
    10. Test airflow and drying performance after repairs.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.