Category: Kenmore

How to Fix Kenmore Refrigerator Error F14
Problem: Ambient temperature sensor fault (models with external temp monitoring)

How to Fix Refrigerator Error
1. UNPLUG unit.
2. Locate ambient sensor – typically mounted on rear cabinet exterior near condenser coils or inside toe grille.
3. Disconnect connector and test resistance (should read 5k-15k ohms at room temp).
4. Replace sensor if open/shorted.
5. Route new sensor wire away from heat sources (condenser coils, compressor).
6. Secure sensor in location with good airflow but protected from direct water exposure.
7. Restore power and verify error clears within 5 minutes.
What to Check Next on This Kenmore Refrigerator

Kenmore Refrigerator Error F14: Use the code or symptom as the starting clue, then confirm what the refrigerator actually does before ordering parts.
1. Unplug the refrigerator before touching wiring, fans, sensors, defrost parts, or control boards.
2. Confirm both doors seal fully, the vents are open, the condenser area is clean, and temperatures have had time to stabilize.
3. Check for frost buildup, fan noise, blocked air returns, warm spots, water-line issues, and loose sensor or harness connections.
4. Note whether the symptom is warm fresh-food air, freezer thawing, ice-maker trouble, dispenser trouble, beeping, or display/control behavior.
5. Replace a part only after the same symptom repeats and model-specific checks point to that part category.
If the issue returns after these checks, match replacement parts to the complete Kenmore refrigerator model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F15
Problem: Ice level sensor circuit failure (optical or mechanical type)

How to Fix Refrigerator Error
1. UNPLUG refrigerator.
2. For optical sensors: Clean emitter/receiver lenses in ice chute with alcohol. Verify alignment. Test circuit continuity. Replace both sensors as pair if faulty.
3. For mechanical arm sensors: Remove ice bin and locate bail arm mechanism on ice maker. Ensure arm moves freely without binding. Check microswitch operation at end of arm travel. Replace ice maker assembly if switch faulty or arm mechanism broken.
4. After repair, verify ice maker stops production when bin is full and resumes when ice level drops.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F16
Problem: Inverter board failure (variable speed compressor models)

How to Fix Refrigerator Error
1. UNPLUG unit for 10 minutes to reset inverter electronics.
2. Restore power and listen for compressor attempting to start (brief humming then shutdown indicates inverter fault).
3. Remove rear access panel to locate inverter board (mounted near compressor, often with large heat sink).
4. Inspect for burnt components, bulging capacitors, or burnt smell.
5. Check DC voltage output to compressor (requires live testing – DANGEROUS – only qualified technicians).
6. If inverter shows physical damage or compressor receives no power, replace inverter board assembly.
7. Verify proper grounding and all connections secure before restoring power.
8. Monitor compressor operation for 24 hours – should run quietly without cycling on thermal overload.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F17
Problem: Air filter status reminder or filter sensor fault (models with internal air purification)

How to Fix Refrigerator Error
1. Locate air filter compartment (typically inside refrigerator rear wall or ceiling).
2. Replace air filter cartridge per manufacturer schedule (usually every 6 months).
3. Reset filter status indicator via control panel menu or button sequence per model instructions.
4. If error persists with new filter, locate filter status sensor/switch.
5. Clean sensor contacts or replace switch assembly if faulty.
6. Verify air circulation fan operates properly after reset.
What to Check Next on This Kenmore Refrigerator

Kenmore Refrigerator Error F17: Use the code or symptom as the starting clue, then confirm what the refrigerator actually does before ordering parts.
1. Unplug the refrigerator before touching wiring, fans, sensors, defrost parts, or control boards.
2. Confirm both doors seal fully, the vents are open, the condenser area is clean, and temperatures have had time to stabilize.
3. Check for frost buildup, fan noise, blocked air returns, warm spots, water-line issues, and loose sensor or harness connections.
4. Note whether the symptom is warm fresh-food air, freezer thawing, ice-maker trouble, dispenser trouble, beeping, or display/control behavior.
5. Replace a part only after the same symptom repeats and model-specific checks point to that part category.
If the issue returns after these checks, match replacement parts to the complete Kenmore refrigerator model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F18
Problem: Secondary freezer sensor fault (dual-sensor freezer models)

How to Fix Refrigerator Error
1. UNPLUG unit.
2. Remove evaporator cover panel in freezer.
3. Locate secondary thermistor (may be mounted on evaporator coil opposite primary sensor or in freezer air stream).
4. Disconnect connector and test resistance.
5. Replace if open/shorted or reading outside specification.
6. Position new sensor in identical location to original.
7. Secure properly to prevent movement during defrost cycles.
8. Restore power and allow 4 hours for temperature stabilization.
What to Check Next on This Kenmore Refrigerator

Kenmore Refrigerator Error F18: Use the code or symptom as the starting clue, then confirm what the refrigerator actually does before ordering parts.
1. Unplug the refrigerator before touching wiring, fans, sensors, defrost parts, or control boards.
2. Confirm both doors seal fully, the vents are open, the condenser area is clean, and temperatures have had time to stabilize.
3. Check for frost buildup, fan noise, blocked air returns, warm spots, water-line issues, and loose sensor or harness connections.
4. Note whether the symptom is warm fresh-food air, freezer thawing, ice-maker trouble, dispenser trouble, beeping, or display/control behavior.
5. Replace a part only after the same symptom repeats and model-specific checks point to that part category.
If the issue returns after these checks, match replacement parts to the complete Kenmore refrigerator model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F19
Problem: Condenser coil temperature sensor fault affecting compressor runtime

How to Fix Refrigerator Error
1. UNPLUG refrigerator and pull away from wall.
2. Remove rear lower access panel.
3. Locate condenser thermistor clipped to condenser coil tubing near compressor (small white probe).
4. Disconnect connector and test resistance (should read 5k-15k ohms at room temp).
5. Replace sensor if faulty.
6. Ensure new sensor makes full metal-to-metal contact with condenser tubing – poor contact causes False high-temp readings triggering premature compressor shutdown.
7. Secure with high-temp adhesive or original clip.
8. Clean condenser coils thoroughly while access panel removed.
What to Check Next on This Kenmore Refrigerator

Kenmore Refrigerator Error F19: Use the code or symptom as the starting clue, then confirm what the refrigerator actually does before ordering parts.
1. Unplug the refrigerator before touching wiring, fans, sensors, defrost parts, or control boards.
2. Confirm both doors seal fully, the vents are open, the condenser area is clean, and temperatures have had time to stabilize.
3. Check for frost buildup, fan noise, blocked air returns, warm spots, water-line issues, and loose sensor or harness connections.
4. Note whether the symptom is warm fresh-food air, freezer thawing, ice-maker trouble, dispenser trouble, beeping, or display/control behavior.
5. Replace a part only after the same symptom repeats and model-specific checks point to that part category.
If the issue returns after these checks, match replacement parts to the complete Kenmore refrigerator model number from the appliance tag. Kenmore models can be built by different manufacturers, so fit depends on the full model number.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F20
Problem: User interface/display board communication failure with main control

How to Fix Refrigerator Error
1. UNPLUG unit for 5 minutes to reset electronics.
2. Restore power and check if display functions return.
3. If display blank or shows error, remove dispenser facade to access display board.
4. Inspect ribbon cable connection between display and main board – reseat firmly.
5. Check for water damage on display board (common from spills into dispenser area).
6. Test voltage at display board connector (should read 5V DC and 12V DC depending on model).
7. If power present but display dead, replace display/user interface board.
8. Transfer any configuration settings per manufacturer instructions after replacement.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 16, 2026
How to Fix Kenmore Refrigerator Error F21
Problem: Refrigerator door ajar sensor fault or door seal failure

How to Fix Refrigerator Error
1. Verify fresh food door fully closed and latched.
2. Inspect door gasket for damage, warping, or debris. Clean thoroughly.
3. Test door switch operation in door frame jamb – should read closed when door shut.
4. Adjust door alignment if needed via hinge screws.
5. Replace door switch if faulty.
6. If gasket damaged, replace entire gasket assembly – requires careful stretching into door groove starting at top center and working down both sides.
7. Perform dollar bill test after repair: close bill in door seal at multiple points – should feel resistance when pulling out, indicating proper seal.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 15, 2026
How to Fix Kenmore Refrigerator Error F22
Problem: Evaporator fan motor speed sensor fault (BLDC motor models)

How to Fix Refrigerator Error
1. UNPLUG unit.
2. Remove evaporator cover panel in freezer.
3. Locate evaporator fan motor with 5-wire harness (includes Hall effect sensor wires).
4. Disconnect harness and test motor windings AND sensor circuit per tech sheet.
5. Manually spin fan blade while monitoring sensor output with oscilloscope (if available) – should show clean pulse waveform.
6. If sensor circuit open/shorted or waveform erratic, replace entire fan motor assembly (sensor not serviceable separately).
7. Check wiring harness for damage between motor and control board.
8. After replacement, verify fan runs at proper speed (should not cycle on/off rapidly).
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 15, 2026
How to Fix Kenmore Refrigerator Error F23
Problem: Defrost termination thermostat fault causing incomplete defrost cycles

How to Fix Refrigerator Error
1. UNPLUG unit and initiate manual defrost until all ice melts.
2. Remove evaporator cover panel in freezer.
3. Locate defrost thermostat clipped to top of evaporator coil (small cylindrical device with 2 wires).
4. Test thermostat when cold/frozen – should read closed (<1 ohm).
5. Warm thermostat to room temperature with hair dryer – should open (OL) at approximately 50-60°F.
6. Replace if fails to open when warm or remains open when cold.
7. Install new thermostat in EXACT same location as original – critical for proper defrost cycle timing.
8. Monitor for 3 complete defrost cycles to verify heater shuts off when evaporator reaches proper temperature.
As an Amazon Associate, we earn from qualifying purchases through links on this page.
When It’s Better to Replace Than Repair

Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

[OK]Water inlet valve, ice maker, or fan failures keep returning

[OK]Defrost heater, thermostat, or sensor faults stack up

[OK]Compressor or sealed-system repair is not economical

[OK]Food-loss risk is becoming a pattern

Recommended Refrigerator Replacement Options

Top-Freezer Models

Simple Full-Size Replacements

Usually lower cost and easy to service

Confirm hinge side and kitchen clearance

Measure width, depth, and height

Shop Top-Freezer Refrigerators

Side-by-Side

Ice and Water Convenience

Good for narrow door swing spaces

Confirm water line and filter access

Check freezer width for large items

Compare Side-by-Side Models

French-Door

Premium Kitchen Layout

Popular wide fresh-food access

Confirm drawer clearance and counter depth

Measure delivery path before ordering

View French-Door Refrigerators

As an Amazon Associate, we earn from qualifying purchases.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
Browse all Kenmore error codes: Kenmore Error Codes
February 15, 2026