Category: Frigidaire

How to Fix Frigidaire Washer Error E43
Error Code: E43 Difficulty: Moderate

Problem: Control board problem or problem with the door lock circuit.

How to Fix E43 Error (Step-by-Step)
1. Disconnect the washer from its power source and confirm the error stays cleared during a full test cycle.
2. Use a pair of pliers or a spring removal tool to take off the outer clamp securing the door bellows to the front of the washer.
3. Gently peel back the rubber bellows around the door lock mechanism to get access.
4. Unscrew the two screws holding the door lock assembly in place.
5. Maneuver the old lock out through the opening and disconnect its electrical connector.
6. Plug the electrical connector into the new door lock assembly and position it correctly.
7. Secure the new lock with its screws, reinstall the door bellows and clamp, and then restore power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E42
Error Code: E42 Difficulty: Moderate

Problem: The door remains locked after the cycle is completed.

How to Fix E42 Error (Step-by-Step)
1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
2. Open the washer door. Use a spring-expansion tool or pliers to expand and remove the outer wire clamp holding the rubber door boot (bellows) to the front panel.
3. Peel the door boot away from the front panel in the area of the door lock assembly.
4. Remove the screws that secure the door lock assembly to the washer’s frame.
5. Reach inside and disconnect the wire harness from the old door lock assembly.
6. Connect the wire harness to the new assembly, then mount the new assembly to the frame with the screws.
7. Re-seat the rubber door boot and secure it with the wire clamp before plugging the washer in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E38
Error Code: E38 Difficulty: Easy

Problem: Clogged air trap.

How to Fix E38 Error (Step-by-Step)
1. Unplug the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
2. Pull the washer away from the wall to access the back panel.
3. Remove the top panel by taking out the screws along the back edge.
4. Locate the pressure switch, which is a round component with a thin rubber or plastic hose attached to it.
5. Disconnect the hose from the pressure switch port and confirm the error stays cleared during a full test cycle.
6. Blow firmly through the hose to clear any trapped lint, soap scum, or debris.
7. Reconnect the hose securely to the pressure switch, replace the top panel, and plug the washer in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E24
Error Code: E24 Difficulty: Hard

Problem: Problem with the drain pump relay.

How to Fix E24 Error (Step-by-Step)
1. Unplug the washing machine from its power source and confirm the error stays cleared during a full test cycle.
2. Slide the washer forward and remove the top panel by unscrewing it from the back.
3. Identify the main control board. It will have numerous wire harnesses connected to it.
4. To avoid errors, take a detailed picture of all the connections before you begin unplugging anything.
5. Systematically disconnect each wire harness from the old board. Pay attention to the small plastic locking clips on each connector.
6. Unscrew the old control board from its mounting points and carefully lift it out.
7. Secure the new main control board in place, reconnect all wires based on your reference photo, and reattach the top panel.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E23
Error Code: E23 Difficulty: Hard

Problem: The drain pump relay on the control board has failed.

How to Fix E23 Error (Step-by-Step)
1. Disconnect the washer from the power source and confirm the error stays cleared during a full test cycle.
2. Remove the top panel of the washer by taking out the screws at the back.
3. Locate the main control board, which is typically a plastic-encased circuit board with many wires connected to it.
4. Take a clear photo of the wire connections to the board to use as a reference.
5. Carefully disconnect all wire harnesses from the old control board. They have locking tabs that need to be pressed.
6. Remove the mounting screws holding the control board in place and install the new board.
7. Reconnect all wire harnesses to the new board according to your photo, replace the top panel, and restore power.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E14
Error Code: E14 Difficulty: Moderate

Problem: Problem with the reed switch.

How to Fix E14 Error (Step-by-Step)
1. Unplug the washer from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Remove the screws from the top panel of the washer, usually located at the back, and slide the panel off.
3. Locate the reed switch, which is a small magnetic switch typically found near the dispenser drawer housing.
4. Disconnect the wire connector attached to the reed switch and confirm the error stays cleared during a full test cycle.
5. Remove the old reed switch, which may be held by a clip or a single screw.
6. Install the new reed switch, reconnect its wire connector, and ensure it is secure.
7. Replace the top panel and secure it with its screws before plugging the washer back in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E13
Error Code: E13 Difficulty: Hard

Problem: Water leak in the tub or air leak in the pressure sensor air hose.

How to Fix E13 Error (Step-by-Step)
1. Unplug the washer from the electrical outlet and turn off the water supply valves.
2. Disconnect the hot and cold water hoses and the drain hose from the back of the washer.
3. Carefully tilt the washer backwards and prop it securely against a wall to access the bottom.
4. Locate the drain pump at the bottom of the machine. Disconnect the wire harness and the hoses attached to it, having a towel ready for residual water.
5. Remove the screws mounting the old drain pump and install the new one in its place.
6. Reconnect the hoses and wire harness to the new pump.
7. Carefully set the washer upright, reconnect all hoses, and plug it back in.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 137221600 (Drain Pump)
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E10
Error Code: E10 Difficulty: Easy

Problem: Water is not entering the washer fast enough.

How to Fix E10 Error (Step-by-Step)
1. Turn off the water supply to the washer at the wall valves.
2. Unscrew the hot and cold water hoses from the back of the machine.
3. Check the small metal filter screens inside the water inlet ports on the washer for any sediment or debris.
4. Clean the screens thoroughly with a small brush and water.
5. Check the entire length of both water hoses for any kinks or twists that could block water flow and straighten them.
6. Reconnect the hoses securely and turn the water supply back on.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E59
Error Code: E59 Difficulty: Hard

Problem: No tacho signal for 3 seconds.

How to Fix E59 Error (Step-by-Step)
1. Disconnect the washer from its power supply by unplugging it from the wall.
2. Remove the service panel, typically at the rear of the washer, to access the drive motor.
3. Locate the wire harness that connects from the motor to the motor control board. The tachometer signal travels through this harness.
4. Inspect the harness for any damage and ensure it is securely plugged in at both the motor and the control board.
5. The tachometer is an internal component of the drive motor and is not sold separately.
6. If the wiring is intact, the entire drive motor must be replaced to fix the faulty tachometer.
7. Install the new motor, reconnect the drive belt and wiring, reassemble the washer, and test for proper operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026
How to Fix Frigidaire Washer Error E58
Error Code: E58 Difficulty: Hard

Problem: High current on motor phase.

How to Fix E58 Error (Step-by-Step)
1. Unplug the washing machine from the electrical outlet to ensure safety.
2. Gain access to the motor and motor control board, usually by removing a rear or bottom service panel.
3. Carefully inspect the wiring that runs between the drive motor and the motor control board. Look for any signs of damage, chafing, or loose connections.
4. A service would test the motor’s electrical windings with a multimeter to check for shorts or open circuits.
5. If the motor windings are out of specification, the entire drive motor assembly needs to be replaced.
6. If the motor tests correctly, the issue points to a faulty motor control board, which must be replaced.
7. After replacing the diagnosed part, reassemble the washer, plug it in, and run a spin cycle to verify the repair.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- 134743500 (Motor Control Board)
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
April 7, 2026