Category: Washer

  • How to Fix Electrolux Washer Error RES

    How to Fix Electrolux Washer Error RES

    Error Code: RES Difficulty: Easy

    Problem: The machine is in a reset state.

    How to Fix RES Error (Step-by-Step)

    1. The ‘RES’ code means the washer is in a reset state, often after a power interruption or a cancelled cycle.
    2. This is not an error, but an informational message and confirm the error stays cleared during a full test cycle.
    3. To clear the ‘RES’ code, you typically need to select a new wash cycle.
    4. Turn the cycle selector knob to your desired wash cycle.
    5. Add any options you want, such as temperature or spin speed.
    6. Press the ‘Start’ button to begin the new cycle. The ‘RES’ message should disappear.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error DR

    How to Fix Electrolux Washer Error DR

    Error Code: DR Difficulty: Easy

    Problem: The door is not closed.

    How to Fix DR Error (Step-by-Step)

    1. Open the washer door completely and confirm the error stays cleared during a full test cycle.
    2. Check for any clothing or other items that may be caught in the door seal or latch mechanism, preventing it from closing properly.
    3. Remove any obstructions you find and confirm the error stays cleared during a full test cycle.
    4. Close the door firmly until you hear a distinct ‘click’ sound, which indicates the latch is engaged.
    5. Turn the appliance off, wait about 2 minutes, then turn it back on.
    6. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    7. Make sure all doors, lids, and hoses are fully closed and seated correctly.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error DDO

    How to Fix Electrolux Washer Error DDO

    Error Code: DDO Difficulty: Hard

    Problem: Drawer reed switch not closed.

    How to Fix DDO Error (Step-by-Step)

    1. Unplug the washer from its power source and confirm the error stays cleared during a full test cycle.
    2. The dispenser drawer has a small magnetic switch that must be closed for the washer to operate. Open the dispenser drawer and locate the reed switch, which is usually a small component at the back of the drawer housing.
    3. Check for any obstructions or detergent buildup that might be preventing the drawer from closing fully and activating the switch.
    4. Clean the area around the switch and the corresponding magnet on the drawer.
    5. If the drawer closes properly but the error persists, the reed switch may be faulty. You can test it for continuity with a multimeter.
    6. To replace the switch, you will need to access the internal components of the dispenser housing, which may require removing the top panel of the washer.
    7. Disconnect the old switch and install the new one, ensuring all connections are secure.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 134399300

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error UNB

    How to Fix Electrolux Washer Error UNB

    Error Code: UNB Difficulty: Easy

    Problem: Unbalanced load detected.

    How to Fix UNB Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the cycle.
    2. Wait for the door to unlock. This may take a few moments.
    3. Open the door and look at the clothes inside. They have likely shifted to one side of the drum.
    4. Avoid washing single, heavy items by themselves as this can easily cause an unbalanced load. Add a few other items to balance the weight.
    5. Close the door securely and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start’ button to resume the wash cycle and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error PAU

    How to Fix Electrolux Washer Error PAU

    Error Code: PAU Difficulty: Easy

    Problem: The wash cycle is paused.

    How to Fix PAU Error (Step-by-Step)

    1. The ‘PAU’ code indicates that the wash cycle has been paused.
    2. To resume the cycle, simply press the ‘Start/Pause’ button.
    3. If you wish to change the cycle or options, you may need to press the ‘Cancel’ button first.
    4. After making any desired changes, select a new cycle and press the ‘Start’ button.
    5. If the machine does not respond, try turning the power off and on again at the circuit breaker to reset the washer’s electronics.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error HO SE

    How to Fix Electrolux Washer Error HO SE

    Error Code: HO SE Difficulty: Easy

    Problem: Reversed hot and cold water hoses.

    How to Fix HO SE Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the current cycle.
    2. Turn off the water supply to the washer at the wall valves.
    3. Check the connections of the hot and cold water hoses on the back of the washing machine.
    4. Ensure the hose marked ‘HOT’ is connected to the hot water inlet valve on the washer and the hot water faucet. The hose marked ‘COLD’ should be connected to the cold water inlet and faucet.
    5. If the hoses are reversed, unscrew them and reconnect them to the correct positions.
    6. Turn the water supply back on and check for any leaks.
    7. Start a new wash cycle to see if the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error F9

    How to Fix Electrolux Washer Error F9

    Error Code: F9 Difficulty: Hard

    Problem: Hot and cold water hoses are inverted.

    How to Fix F9 Error (Step-by-Step)

    1. First, unplug the washer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Check the hot and cold water inlet hoses at the back of the machine to ensure they are connected to the correct faucets. The hose for hot water should be connected to the hot water tap, and the cold to the cold.
    3. If the hoses are correct, the issue may be with the drive motor. This is a more complex repair.
    4. To access the drive motor, you will likely need to remove the back panel of the washer.
    5. The drive motor is located at the bottom of the tub. Inspect it for any visible signs of damage or loose connections.
    6. If you have a multimeter, you can test the motor for continuity. A lack of continuity indicates a faulty motor that needs replacement.
    7. Replacing the drive motor involves disconnecting it from the power supply, removing the belt, and unbolting it from the washer frame.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error F8

    How to Fix Electrolux Washer Error F8

    Error Code: F8 Difficulty: Hard

    Problem: Water level sensor fault.

    How to Fix F8 Error (Step-by-Step)

    1. Unplug the washer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Turn off both the hot and cold water supplies to the washer.
    3. Locate the water level sensor, which is typically a small, round part with a tube and wires connected to it, often found behind the control panel or in the upper part of the washer cabinet.
    4. Carefully disconnect the wiring harness and the air tube from the old sensor.
    5. Remove the screws or clips holding the sensor in place and take it out.
    6. Install the new water level sensor, making sure to securely reattach the air tube and wiring harness.
    7. Reassemble the washer, turn the water back on, and plug the machine back in to test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • 5304505436
    • 5304511335

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error F6

    How to Fix Electrolux Washer Error F6

    Error Code: F6 Difficulty: Hard

    Problem: Control reset.

    How to Fix F6 Error (Step-by-Step)

    1. Unplug the washer from the wall outlet or turn off the circuit breaker. Wait for at least 5 minutes to allow any stored electrical charge to dissipate completely.
    2. Remove the top panel of the washer by unscrewing the screws holding it in place, typically located at the back or sides of the machine.
    3. Locate the main control board, which is usually a green circuit board housed in a plastic case. Carefully inspect all the wire harnesses and connectors attached to the board for any signs of loose connections, corrosion, or damage.
    4. If all connections are secure, the control board itself likely needs replacement. One by one, disconnect each wire connector from the old board, taking a photo beforehand for reference. Remove the screws or clips holding the board in its housing and install the new main control board.
    5. Carefully reconnect all wire harnesses to the new board, referencing the photo you took to ensure they are in the correct positions. Secure the new board in its housing.
    6. Before reassembling, also inspect the door lock assembly. Check its wiring and ensure the mechanism isn’t physically damaged. If it appears faulty, it should also be replaced by disconnecting its wiring and removing its mounting screws.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes

  • How to Fix Electrolux Washer Error F5

    How to Fix Electrolux Washer Error F5

    Error Code: F5 Difficulty: Easy

    Problem: A keypad problem has been detected.

    How to Fix F5 Error (Step-by-Step)

    1. Press the ‘Cancel’ button twice to attempt to clear the error code.
    2. Unplug the washing machine from the power source for at least 5 minutes to perform a hard reset.
    3. While unplugged, gently wipe the surface of the keypad and control panel with a soft, dry cloth to remove any moisture or residue that might be causing a button to stick.
    4. For more stubborn residue, you can use a cloth lightly dampened with water or a mild cleaner. Ensure the panel is completely dry before restoring power.
    5. Plug the washer back in and try to start a new cycle.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Electrolux error codes: Electrolux Error Codes