Electrolux Dryer error code
Electrolux Dryer Error F01
Internal fault in the control.
Internal fault in the control.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Check 1
Press the 'Stop/Clear' or 'Cancel' button to try and clear the code.
- 2Check 2
Unplug the dryer for 30 seconds and then plug it back in to perform a hard reset.
- 3Check 3
Visually inspect the main control board for any signs of burns or damage after unplugging the unit.
A quick explanation
What does F01 mean?
Internal fault in the control.
The answer you came for
How to fix Electrolux dryer error F01
Start with the safest checks and work from simple to technical.
- 1
Step 1
1. Disconnect the dryer from its power supply.
- 2
Step 2
2. The F01 code indicates an internal failure of the main control board. Access the control board by removing the top panel of the dryer.
- 3
Step 3
3. Before replacing, visually inspect the control board for any obvious signs of damage, such as burn marks or loose connections. Re-seat any loose connectors.
- 4
Step 4
4. If no visible issues are found, the control board needs to be replaced. Carefully disconnect all wire harnesses from the old board.
- 5
Step 5
5. Remove the screws securing the control board and take it out.
- 6
Step 6
6. Place the new control board in the same position and secure it with the screws.
- 7
Step 7
7. Reconnect all the wire harnesses to the new board, ensuring each is in the correct spot, then reattach the top panel.
Read the additional checks from the current guide
How to Fix F01 Error (Step-by-Step) Disconnect the dryer from its power supply and confirm the error stays cleared during a full test cycle.The F01 code indicates an internal failure of the main control board. Access the control board by removing the top panel of the dryer.Before replacing, visually inspect the control board for any obvious signs of damage, such as burn marks or loose connections. Re-seat any loose connectors.If no visible issues are found, the control board needs to be replaced. Carefully disconnect all wire harnesses from the old board.Remove the screws securing the control board and take it out.Place the new control board in the same position and secure it with the screws.Reconnect all the wire harnesses to the new board, ensuring each is in the correct spot, then reattach the top panel.Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dryer Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dryer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dryer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. Verified Compatible Alternatives:A144718035304510361
What may be causing it?
- Internal failure of the main electronic control board
These are possibilities to investigate, not proof that one part has failed.
Recommended part
Recommended part for this error code
Replacement part
OEM candidate: 5304525687
Price noted in the current guide: $173-$249
Why this part is shown: It is associated with Electrolux Dryer error F01 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dryer?
If repairing this dryer no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$599
Budget-friendly dryers in the $0-$599 range.
Shop Value Options on AmazonBest Overall
$600-$999
Balanced dryers in the $600-$999 range.
Shop Best Overall Options on AmazonPremium
$1,000-$2,500
Higher-end dryers in the $1,000-$2,500 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Electrolux Dryer Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.