Category: Bosch

How to Fix Bosch Dishwasher Error INTENSIVE/HEAVY CYCLE SYMBOL (POT)
Error Code: INTENSIVE/HEAVY CYCLE SYMBOL (POT) Difficulty: Easy

Problem: The intensive or heavy-duty cycle is selected.

How to Fix INTENSIVE/HEAVY CYCLE SYMBOL (POT) Error (Step-by-Step)
1. Locate the symbol of a pot on your dishwasher’s display. This indicates that the ‘Intensive’ or ‘Heavy’ duty wash cycle is selected.
2. This is a normal operational symbol and not an error code.
3. This cycle is specifically designed for cleaning heavily soiled items, such as pots, pans, and casseroles with baked-on food.
4. It uses higher water temperatures and increased spray pressure to remove tough grime.
5. If you have selected this cycle by mistake for a load of lightly soiled or delicate items, you can cancel it. Press and hold the ‘Start/Reset’ button for approximately 3 seconds.
6. Once the cycle is canceled, you can choose a more suitable program for your dish load.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 13, 2026
How to Fix Bosch Dishwasher Error HYGIENEPLUS SYMBOL
Error Code: HYGIENEPLUS SYMBOL Difficulty: Easy

Problem: Indicates a feature that uses a hotter final rinse (up to 70°C) for a higher anti-bacterial performance.

How to Fix HYGIENEPLUS SYMBOL Error (Step-by-Step)
1. Notice the ‘HygienePlus’ symbol is lit on the control panel. This signifies that a specific wash option has been activated.
2. This is not an error message. It indicates the dishwasher will use a final rinse with water heated up to 70°C for enhanced sanitation.
3. This feature is designed to provide a more hygienic clean for your dishes.
4. If you did not intend to use this option, press the ‘HygienePlus’ button again to deselect it before the wash cycle begins.
5. If the wash is already in progress, allow the cycle to finish to gain the benefit of the sanitary rinse.
6. For your next load, simply select your preferred wash cycle without adding the ‘HygienePlus’ option if it’s not needed.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 13, 2026
How to Fix Bosch Dishwasher Error HYGIENE/HYGIENE PLUS SYMBOL
Error Code: HYGIENE/HYGIENE PLUS SYMBOL Difficulty: Easy

Problem: A hotter final rinse is held for longer for a higher anti-bacterial performance.

How to Fix HYGIENE/HYGIENE PLUS SYMBOL Error (Step-by-Step)
1. Identify the ‘Hygiene’ or ‘Hygiene Plus’ symbol on the dishwasher’s display. This is an indicator for a selected feature, not an error.
2. Understand that this setting provides a higher temperature final rinse for an increased anti-bacterial effect.
3. This option is particularly useful for sanitizing items like baby bottles, canning jars, or cutting boards.
4. If you do not need this level of sanitation for your current load, you can deactivate the feature by pressing the corresponding ‘Hygiene’ or ‘Hygiene Plus’ button.
5. If the cycle has already started, it is best to let it complete.
6. For future washes, simply avoid selecting this option unless you specifically require a sanitizing rinse.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 13, 2026
How to Fix Bosch Dishwasher Error HALF LOAD SYMBOL
Error Code: HALF LOAD SYMBOL Difficulty: Easy

Problem: Allows for running a wash cycle with a smaller load to save water and energy.

How to Fix HALF LOAD SYMBOL Error (Step-by-Step)
1. This symbol shows that the ‘Half Load’ option is active.
2. This feature is useful when you only have a few dishes to wash, as it uses less water and energy.
3. To use this option, load the dishes (it’s often recommended to use the top rack, but check your model’s preference) and press the ‘Half Load’ button.
4. The indicator light for the symbol will turn on and confirm the error stays cleared during a full test cycle.
5. Select your desired wash cycle and press ‘Start’ and confirm the error stays cleared during a full test cycle.
6. To turn off the option for a full load, simply press the ‘Half Load’ button again before starting a cycle so the light goes out.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error GLASS 40° SYMBOL
Error Code: GLASS 40° SYMBOL Difficulty: Easy

Problem: Represents a gentle cleaning cycle with lower temperatures (around 40°C) and an extended drying period, designed for delicate glassware.

How to Fix GLASS 40° SYMBOL Error (Step-by-Step)
1. This symbol indicates that the ‘Glass 40°’ cycle is selected.
2. This cycle is specifically designed for delicate items like glassware, using a lower temperature to prevent damage.
3. To use this cycle, load your delicate items and press the button corresponding to this symbol.
4. Add detergent as usual and press the ‘Start’ button to begin the wash.
5. If you have selected this cycle by mistake, you can typically cancel it by pressing the ‘Cancel’ or ‘Reset’ button and then choose a different cycle.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error F24
Error Code: F24 Difficulty: Hard

Problem: The water pump is blocked.

How to Fix F24 Error (Step-by-Step)
1. Disconnect the dishwasher from power by unplugging it or switching off the circuit breaker.
2. Shut off the water supply to the dishwasher, typically located under the sink.
3. Remove the bottom dish rack, lower spray arm, and filter assembly from inside the dishwasher tub to access the drain pump cover.
4. Place a towel under the pump cover and carefully pry it open to check for any visible obstructions like glass shards, food particles, or small bones. Remove any debris found.
5. If no blockage is found, you will need to access the pump from underneath. Carefully pull the dishwasher out from the cabinet and lay it on its back on a soft towel or blanket.
6. Remove the base cover panel. Locate the drain pump, disconnect the wire harness, and unclamp the hoses. Have a shallow pan and towels ready to catch residual water.
7. Remove the old pump, which is often held in place by a few screws or a twist-lock mechanism. Install the new pump, reconnect the hoses and electrical connector, and reassemble the dishwasher in reverse order.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error F15
Error Code: F15 Difficulty: Hard

Problem: The water protection system has been activated to prevent flooding.

How to Fix F15 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker and shut off the water supply valve, usually located under the sink.
2. Carefully slide the dishwasher out from under the counter. You may need to remove the mounting screws securing it to the countertop first.
3. Place towels on the floor and carefully tilt the dishwasher forward at a 45-degree angle to allow water trapped in the base pan to drain out.
4. With the dishwasher on its back, remove the screws holding the base panel to access the internal components.
5. Inspect the sump, hoses, and the heat pump/circulation motor for any visible signs of cracks, damage, or loose connections that could be the source of the leak. The heat pump is a common source for leaks.
6. Replace the faulty component. This often involves disconnecting hoses and electrical connectors, removing the old part, and installing the new one in its place.
7. Reassemble the dishwasher by reattaching the base panel, sliding it back into place, securing it, and reconnecting the power and water supply before running a test cycle.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error F14
Error Code: F14 Difficulty: Hard

Problem: Water intake fault where the heater pressure switch registers no or insufficient water pressure at the circulation pump during the heating step.

How to Fix F14 Error (Step-by-Step)
1. Disconnect the dishwasher from power by turning off the circuit breaker and shut off the water supply valve, usually located under the sink.
2. Carefully pull the dishwasher out from under the counter. You may need to remove mounting screws from the countertop brackets first.
3. Lay the dishwasher on its back or side on a towel to access the components underneath.
4. Locate the water inlet valve, which is where the main water line connects to the dishwasher. It will have an electrical connector and a hose attached.
5. Disconnect the wire harness from the valve. Place a small pan or towel underneath and then disconnect the water line and any other hoses.
6. Remove the screws holding the old valve in place and install the new one, ensuring all connections are secure.
7. Reconnect the wire harness and hoses, then carefully set the dishwasher upright, slide it back into place, and reconnect the power and water before testing.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error F12
Error Code: F12 Difficulty: Hard

Problem: Water intake fault at the start of a cycle, with no pulses detected from the flow meter.

How to Fix F12 Error (Step-by-Step)
1. Turn off the power to the dishwasher at the circuit breaker and shut off the water supply valve, which is typically located under the sink.
2. Carefully pull the dishwasher out from under the counter to access the water connections. Place a towel underneath the water inlet hose connection to catch any residual water.
3. Inspect the water inlet hose for any kinks or sharp bends that could be restricting water flow. Straighten the hose if necessary.
4. Disconnect the water inlet hose from the dishwasher. Check the small filter screen inside the inlet valve for any debris or sediment buildup and clean it thoroughly with a small brush under running water.
5. If the hose and filter are clear, the water inlet valve and flow meter assembly is likely faulty. This part is usually located on the left side of the dishwasher base. Disconnect the wiring harness and hoses attached to the old valve.
6. Install the new water inlet valve assembly, ensuring all hose clamps and electrical connectors are securely fastened in the same positions as the original part.
7. Reconnect the main water supply hose, slide the dishwasher back into place, turn the water supply and circuit breaker back on, and run a test cycle to ensure the error is resolved.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026
How to Fix Bosch Dishwasher Error EXTRA DRY SYMBOL
Error Code: EXTRA DRY SYMBOL Difficulty: Easy

Problem: Indicates that the Extra Dry option is selected, which uses a higher temperature during the final rinse and a longer drying phase.

How to Fix EXTRA DRY SYMBOL Error (Step-by-Step)
1. Understand that this symbol indicates the ‘Extra Dry’ feature is active, which improves drying results.
2. This option is selected before starting a wash cycle and confirm the error stays cleared during a full test cycle.
3. If you wish to deactivate it for the next load, press the ‘Extra Dry’ button to turn the light off.
4. If you want to use it, press the button to enable the feature before you start the wash.
5. This function increases the final rinse temperature and extends the drying time, which is normal.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Bosch error codes: Bosch Error Codes
May 12, 2026