Category: Bosch

  • How to Fix Bosch Dishwasher Error SHINE & DRY SYMBOL

    How to Fix Bosch Dishwasher Error SHINE & DRY SYMBOL

    Error Code: SHINE & DRY SYMBOL Difficulty: Easy

    Problem: An option that uses more water during the rinse cycle and extends the drying phase to prevent watermarks and improve drying results.

    How to Fix SHINE & DRY SYMBOL Error (Step-by-Step)

    1. Notice the Shine & Dry symbol on the control panel. This is an optional setting you can select, not an error message.
    2. Understand that this function improves the drying performance, especially for plastics, and enhances the shine on glassware.
    3. To activate this option, first select your desired main wash program (e.g., Auto, Normal, Heavy).
    4. Before starting the cycle, press the button corresponding to the Shine & Dry symbol. An indicator light will usually confirm it has been selected.
    5. Be aware that selecting this option will increase the final rinse temperature and extend the drying phase, which may increase the overall cycle time and energy consumption.
    6. If you do not need enhanced drying for a particular load, simply do not select the option after choosing your main program.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error SALT SYMBOL (S-SHAPED ARROWS)

    How to Fix Bosch Dishwasher Error SALT SYMBOL (S-SHAPED ARROWS)

    Error Code: SALT SYMBOL (S-SHAPED ARROWS) Difficulty: Easy

    Problem: The dishwasher salt reservoir needs to be refilled.

    How to Fix SALT SYMBOL (S-SHAPED ARROWS) Error (Step-by-Step)

    1. Identify the Salt symbol, which looks like two S-shaped arrows, lit up on the control panel. This means the water softener needs more dishwasher salt.
    2. Open the dishwasher door and pull out the bottom rack completely to access the floor of the dishwasher tub.
    3. Locate the salt reservoir cap, which is a large, round cap, and unscrew it by turning it counter-clockwise.
    4. If this is the first time you are adding salt, you must first fill the reservoir with about 1 liter of water.
    5. Place the funnel that came with your dishwasher into the opening. Slowly pour in dishwasher-specific salt until the reservoir is full.
    6. Remove the funnel and clean any excess salt from around the opening. Screw the cap back on tightly in a clockwise direction.
    7. Run a short rinse or wash cycle immediately after refilling the salt to wash away any spilled salt granules and to activate the softener.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error RINSE AID SYMBOL (SUN/STARBURST)

    How to Fix Bosch Dishwasher Error RINSE AID SYMBOL (SUN/STARBURST)

    Error Code: RINSE AID SYMBOL (SUN/STARBURST) Difficulty: Easy

    Problem: The rinse aid dispenser needs to be refilled.

    How to Fix RINSE AID SYMBOL (SUN/STARBURST) Error (Step-by-Step)

    1. Locate the Rinse Aid symbol, which looks like a sun or starburst, illuminated on your dishwasher’s display. This indicates the rinse aid level is low.
    2. Open the dishwasher door completely. Find the rinse aid dispenser, which is a round compartment typically located next to the main detergent dispenser on the inside of the door.
    3. Turn the dispenser cap counter-clockwise to open it. Some models may have a lid that flips open instead.
    4. Slowly pour liquid rinse aid into the opening until the indicator window or level gauge shows it is full. Be careful not to overfill.
    5. Wipe up any spilled rinse aid with a cloth to prevent excess foaming during the next wash cycle.
    6. Securely close the dispenser by replacing the cap and turning it clockwise until it locks, or by snapping the lid shut.
    7. The illuminated symbol on the display will turn off after the next wash cycle begins.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)

    How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)

    Error Code: RED LIGHT ON FLOOR (INFOLIGHT) Difficulty: Easy

    Problem: The dishwasher is currently operating.

    How to Fix RED LIGHT ON FLOOR (INFOLIGHT) Error (Step-by-Step)

    1. Observe the steady red light projected onto the floor below your dishwasher.
    2. Recognize that this light, known as InfoLight, is a normal operational feature and not an error indicator.
    3. Understand that the red light’s purpose is to show that a wash cycle is currently in progress. This is especially useful for fully integrated models where the control panel is not visible.
    4. Do not attempt to open the dishwasher while this light is on, as hot water and steam may be released.
    5. Wait for the wash and dry cycle to complete. The red light will automatically turn off once the cycle has finished.
    6. Once the light is off, it is safe to open the dishwasher and unload your clean dishes.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error QUICK/EXPRESS CYCLE SYMBOL

    How to Fix Bosch Dishwasher Error QUICK/EXPRESS CYCLE SYMBOL

    Error Code: QUICK/EXPRESS CYCLE SYMBOL Difficulty: Easy

    Problem: Signifies a shorter wash cycle for lightly soiled dishes.

    How to Fix QUICK/EXPRESS CYCLE SYMBOL Error (Step-by-Step)

    1. Identify the Quick/Express Cycle symbol on your dishwasher’s control panel. It often looks like a clock with an arrow or a similar speed-related icon.
    2. Understand that this is not an error, but a selectable wash cycle designed for lightly soiled dishes, glasses, and cutlery that do not have dried-on food.
    3. To use this cycle, first load your dishwasher with the lightly soiled items.
    4. Press the power button and then select the Quick/Express Cycle button.
    5. Add the appropriate amount of detergent for a light load.
    6. Close the dishwasher door and press the Start button to begin the shorter wash cycle.
    7. Be aware that this cycle uses less water and energy, and has a shorter drying time, so it may not be suitable for heavily soiled pots and pans.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error PRE-RINSE SYMBOL (SPRAY OF WATER)

    How to Fix Bosch Dishwasher Error PRE-RINSE SYMBOL (SPRAY OF WATER)

    Error Code: PRE-RINSE SYMBOL (SPRAY OF WATER) Difficulty: Easy

    Problem: The pre-rinse cycle is active.

    How to Fix PRE-RINSE SYMBOL (SPRAY OF WATER) Error (Step-by-Step)

    1. Identify the symbol resembling a spray of water on the display. This indicates the ‘Pre-Rinse’ cycle is active.
    2. This is a normal cycle selection and not an error code.
    3. The Pre-Rinse cycle is a brief program that uses a small amount of cold water to rinse dishes.
    4. Its purpose is to prevent food soils from drying onto plates if you are not planning to run a full wash cycle immediately.
    5. This cycle does not use detergent and is not intended to fully clean the dishes.
    6. If you selected this by mistake, you can cancel the program by pressing and holding the ‘Start/Reset’ button for about 3 seconds, then select a full wash program.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error PERFECTDRY

    How to Fix Bosch Dishwasher Error PERFECTDRY

    Error Code: PERFECTDRY Difficulty: Easy

    Problem: A drying system that uses Zeolith minerals to absorb moisture and convert it into warm air for improved drying results, especially on plastic items.

    How to Fix PERFECTDRY Error (Step-by-Step)

    1. See the ‘PerfectDry’ light or symbol on your dishwasher’s control panel. This is an indicator of an active feature, not an error.
    2. This symbol means your dishwasher is using its advanced Zeolith drying technology.
    3. The system uses natural Zeolith minerals to absorb moisture from the wash cycle and convert it into warm, dry air.
    4. This warm air is then circulated throughout the tub, resulting in superior drying performance, especially for plastic items.
    5. This feature is automatic and engages with certain cycles to ensure your dishes, including plastics, come out exceptionally dry.
    6. No action is needed. The dishwasher is operating as designed to provide the best possible drying results.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error MACHINE CARE SYMBOL

    How to Fix Bosch Dishwasher Error MACHINE CARE SYMBOL

    Error Code: MACHINE CARE SYMBOL Difficulty: Easy

    Problem: It is time to run the “Machine Care” cleaning cycle.

    How to Fix MACHINE CARE SYMBOL Error (Step-by-Step)

    1. Notice the ‘Machine Care’ symbol (often looks like a sparkling dishwasher) is illuminated. This is a maintenance reminder, not a malfunction.
    2. The dishwasher is prompting you to run its self-cleaning cycle to remove grease and limescale buildup from the interior.
    3. First, ensure the dishwasher is completely empty. Remove all dishes, cutlery, and any food debris from the filter.
    4. Pour a dishwasher cleaning agent specifically designed for machine care directly into the empty dishwasher tub or into the detergent dispenser, following the product’s instructions.
    5. Close the dishwasher door securely and confirm the error stays cleared during a full test cycle.
    6. Select the ‘Machine Care’ program by pressing the corresponding button and then press ‘Start’.
    7. Allow the cycle to run fully without interruption. This will deep clean the interior, spray arms, and filter, ensuring optimal performance and hygiene.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error LOADSENSOR

    How to Fix Bosch Dishwasher Error LOADSENSOR

    Error Code: LOADSENSOR Difficulty: Easy

    Problem: A feature that detects the size of the load to adjust water and energy consumption accordingly.

    How to Fix LOADSENSOR Error (Step-by-Step)

    1. See the ‘LoadSensor’ indicator on the display. This is not an error but an indication of a smart feature at work.
    2. This feature uses sensors to automatically detect the size of the load of dishes inside the dishwasher.
    3. Based on the detected load size, the dishwasher’s control unit adjusts the water and energy consumption for that specific cycle.
    4. This ensures optimal cleaning performance while conserving resources for smaller loads.
    5. No action is required from you. The process is entirely automatic.
    6. You can continue to use your dishwasher as normal, knowing it is operating efficiently.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error INTENSIVEZONE SYMBOL

    How to Fix Bosch Dishwasher Error INTENSIVEZONE SYMBOL

    Error Code: INTENSIVEZONE SYMBOL Difficulty: Easy

    Problem: An option that increases spray pressure and temperature in the lower basket for heavily soiled pots and pans, while the upper basket receives a standard wash.

    How to Fix INTENSIVEZONE SYMBOL Error (Step-by-Step)

    1. Observe the ‘IntensiveZone’ symbol on the control panel. This indicates a specialized wash option has been activated.
    2. This is a feature, not a fault. It creates two distinct cleaning zones within the dishwasher.
    3. The lower basket receives a more intense wash with higher spray pressure and temperature, ideal for heavily soiled pots and pans.
    4. Simultaneously, the upper basket receives a standard, gentler wash suitable for glasses and plates.
    5. To turn this feature off, simply press the ‘IntensiveZone’ button before starting the dishwasher.
    6. If the cycle is already running, let it complete. Remember to deselect the option for future loads if you are washing similar items in both racks.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes