Category: Bosch

  • How to Fix Bosch Dryer Error F18

    How to Fix Bosch Dryer Error F18

    Error Code: F18 Difficulty: Hard

    Problem: Drainage issue or fault with the heating element during the drying cycle.

    How to Fix F18 Error (Step-by-Step)

    1. Disconnect the dryer from the power outlet to ensure safety.
    2. Locate the drain pump, which is typically behind the lower front access panel. You may need a screwdriver to remove the panel.
    3. Place a shallow tray and towels under the pump access to catch residual water.
    4. Carefully unscrew the pump cover or cap, allowing the water to drain out completely.
    5. Inspect the pump impeller and housing for any lint, debris, or foreign objects that could be causing a blockage. Clear any obstructions you find.
    6. Once clear, securely screw the pump cover back on, ensuring a watertight seal.
    7. Reattach the front access panel, plug the dryer back in, and run a test cycle to confirm the error is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    What to Check Next on This Bosch Dryer

    Use these checks before ordering parts for Bosch dryer F18. They keep the diagnosis tied to the appliance instead of turning the page into a reset-only guide.

    1. Unplug the dryer before touching the lint housing, rear vent, lower service area, or any wiring.
    2. Clean the lint screen, moisture sensor bars, condenser area if equipped, and the full vent path so airflow problems do not imitate part failures.
    3. Run a short timed cycle with a light load and note whether the fault appears immediately, after heating starts, or near the end of the cycle.
    4. If the fault returns with clean airflow, inspect the part categories below using the full model number from the dryer tag.
    5. Stop repeated test cycles if you smell heat, see moisture near electrical areas, or hear grinding from the drum drive.

    Recommended Parts to Check

    Bosch dryer part numbers vary by model. These are model-number-safe part-category searches, not universal fit claims.

    • Dryer lint screen
      Common replacement category: lint filter
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Start with lint restrictions when heating, airflow, or maintenance warnings appear.

      Search Amazon for Dryer lint screen

    • Dryer thermal fuse
      Common replacement category: thermal protection
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Common safety device to inspect after overheating or no-heat symptoms.

      Search Amazon for Dryer thermal fuse

    • Dryer drum belt
      Common replacement category: drive system
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Worth checking when the dryer tumbles poorly, stalls, or makes drive noise.

      Search Amazon for Dryer drum belt

    • Dryer moisture sensor
      Common replacement category: sensor circuit
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Useful category to verify when dryness or care/maintenance messages persist.

      Search Amazon for Dryer moisture sensor

    Before ordering: match the part to the complete model number on the appliance tag.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dryer Error F86

    How to Fix Bosch Dryer Error F86

    Error Code: F86 Difficulty: Easy

    Problem: Salt container lid contact fault (on models with this feature).

    How to Fix F86 Error (Step-by-Step)

    1. Turn off and unplug the dryer from the electrical outlet for safety.
    2. Locate the salt container; its position can vary, so check the area around the base of the dryer.
    3. Open the lid to the salt container and confirm the error stays cleared during a full test cycle.
    4. Check to ensure there is no debris or obstruction on the lid or the container’s contact points.
    5. Securely close the lid, making sure it is tightened properly and sits flush.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    What to Check Next on This Bosch Dryer

    Use these checks before ordering parts for Bosch dryer F86. They keep the diagnosis tied to the appliance instead of turning the page into a reset-only guide.

    1. Unplug the dryer before touching the lint housing, rear vent, lower service area, or any wiring.
    2. Clean the lint screen, moisture sensor bars, condenser area if equipped, and the full vent path so airflow problems do not imitate part failures.
    3. Run a short timed cycle with a light load and note whether the fault appears immediately, after heating starts, or near the end of the cycle.
    4. If the fault returns with clean airflow, inspect the part categories below using the full model number from the dryer tag.
    5. Stop repeated test cycles if you smell heat, see moisture near electrical areas, or hear grinding from the drum drive.

    Recommended Parts to Check

    Bosch dryer part numbers vary by model. These are model-number-safe part-category searches, not universal fit claims.

    • Dryer lint screen
      Common replacement category: lint filter
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Start with lint restrictions when heating, airflow, or maintenance warnings appear.

      Search Amazon for Dryer lint screen

    • Dryer thermal fuse
      Common replacement category: thermal protection
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Common safety device to inspect after overheating or no-heat symptoms.

      Search Amazon for Dryer thermal fuse

    • Dryer drum belt
      Common replacement category: drive system
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Worth checking when the dryer tumbles poorly, stalls, or makes drive noise.

      Search Amazon for Dryer drum belt

    • Dryer moisture sensor
      Common replacement category: sensor circuit
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Useful category to verify when dryness or care/maintenance messages persist.

      Search Amazon for Dryer moisture sensor

    Before ordering: match the part to the complete model number on the appliance tag.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dryer Error H9E

    How to Fix Bosch Dryer Error H9E

    Error Code: H9E Difficulty: Moderate

    Problem: Issue with the hot water tap, supply hose, or water pressure.

    How to Fix H9E Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet and turn off the hot water supply valve completely.
    2. Locate the hot water inlet hose on the back of the dryer. Check the entire length of the hose for any kinks, sharp bends, or visible signs of damage like cracks or leaks.
    3. Unscrew the hose from the back of the dryer. Place a small towel underneath to catch any residual water. Look inside the connection port on the dryer for a small filter screen and check if it’s clogged with sediment or debris. Clean it gently with a small brush if needed.
    4. Disconnect the other end of the hose from the house’s hot water supply valve. Point the hose into a bucket and briefly turn on the water valve to check the water pressure. If the flow is weak, the issue may be with your home’s plumbing rather than the dryer.
    5. If the hose is damaged or the filter screen is clean and water pressure seems adequate, the hose itself may be faulty. Replace it with a new hot water inlet hose.
    6. Securely attach the new hose to both the dryer and the water supply valve, ensuring the connections are hand-tight plus a quarter turn with pliers to prevent leaks.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    What to Check Next on This Bosch Dryer

    Use these checks before ordering parts for Bosch dryer H9E. They keep the diagnosis tied to the appliance instead of turning the page into a reset-only guide.

    1. Unplug the dryer before touching the lint housing, rear vent, lower service area, or any wiring.
    2. Clean the lint screen, moisture sensor bars, condenser area if equipped, and the full vent path so airflow problems do not imitate part failures.
    3. Run a short timed cycle with a light load and note whether the fault appears immediately, after heating starts, or near the end of the cycle.
    4. If the fault returns with clean airflow, inspect the part categories below using the full model number from the dryer tag.
    5. Stop repeated test cycles if you smell heat, see moisture near electrical areas, or hear grinding from the drum drive.

    Recommended Parts to Check

    Bosch dryer part numbers vary by model. These are model-number-safe part-category searches, not universal fit claims.

    • Dryer lint screen
      Common replacement category: lint filter
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Start with lint restrictions when heating, airflow, or maintenance warnings appear.

      Search Amazon for Dryer lint screen

    • Dryer thermal fuse
      Common replacement category: thermal protection
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Common safety device to inspect after overheating or no-heat symptoms.

      Search Amazon for Dryer thermal fuse

    • Dryer drum belt
      Common replacement category: drive system
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Worth checking when the dryer tumbles poorly, stalls, or makes drive noise.

      Search Amazon for Dryer drum belt

    • Dryer moisture sensor
      Common replacement category: sensor circuit
      Fit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.
      Why check it: Useful category to verify when dryness or care/maintenance messages persist.

      Search Amazon for Dryer moisture sensor

    Before ordering: match the part to the complete model number on the appliance tag.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
    Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
    For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Thermal fuse or heater failures keep returning
    • [OK]Belt, roller, or motor repairs exceed unit value
    • [OK]Door switch or control issues stack with other faults
    • [OK]Older dryer has long dry times even after vent cleaning

    Recommended Dryer Replacement Options

    Electric Dryers

    240V Vented Models

    • Most common electric replacement type
    • Confirm 3-prong vs 4-prong cord needs
    • Verify vent path and laundry-space depth

    Shop Electric Dryers

    Gas Dryers

    Natural Gas Dryer Options

    • Confirm gas supply and shutoff location
    • Use qualified installation when required
    • Do not substitute electric for gas without planning

    Compare Gas Dryers

    Compact and Ventless

    Small-Space Dryer Choices

    • Good for apartments and tight closets
    • Confirm ventless condensation requirements
    • Check capacity before replacing full-size units

    View Compact Dryers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E0100

    How to Fix Bosch Dishwasher Error E0100

    Error Code: E0100 Difficulty: Easy

    Problem: Main control board relay fault/error.

    How to Fix E0100 Error (Step-by-Step)

    1. For your safety, begin by completely cutting power to the dishwasher at the source. Go to your home’s main electrical panel (circuit breaker box).
    2. Identify the circuit breaker that supplies power to your Bosch dishwasher.
    3. Flip the identified breaker to the full ‘OFF’ position to ensure no electricity is flowing to the appliance.
    4. Wait for a minimum of 15 minutes. This extended period allows the dishwasher’s internal computer and components to fully discharge and reset from the fault state.
    5. After waiting, return to the electrical panel and flip the dishwasher’s circuit breaker back to the ‘ON’ position.
    6. Go back to your dishwasher and try to start a short wash cycle, like ‘Rinse Only’.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E0100: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error E0103

    How to Fix Bosch Dishwasher Error E0103

    Error Code: E0103 Difficulty: Hard

    Problem: Main control board relay fault/error.

    How to Fix E0103 Error (Step-by-Step)

    1. Press the On/Off button to turn the dishwasher off.
    2. To ensure your safety, completely disconnect the appliance from its power source. Either unplug the power cord from the wall outlet or switch off the dedicated circuit breaker in your home’s fuse box.
    3. Let the dishwasher remain without power for a minimum of 15 minutes. This extended time allows the internal electronic components and the main control board to fully discharge and reset.
    4. After the 15-minute period has passed, restore power to the dishwasher by plugging it back in or flipping the circuit breaker on.
    5. Power on the dishwasher and try to start a new cleaning cycle to see if the error has been cleared.
    6. This issue cannot be resolved with a simple part replacement and requires professional service. The main control board will need to be diagnosed and replaced by a qualified service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E0103: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error E0107

    How to Fix Bosch Dishwasher Error E0107

    Error Code: E0107 Difficulty: Hard

    Problem: Indicates an overheating at the main connection, leading to the end of the program.

    How to Fix E0107 Error (Step-by-Step)

    1. Immediately shut off power to the dishwasher at the main circuit breaker to eliminate the risk of electric shock.
    2. Carefully pull the dishwasher out from its installation spot to get access to the power connections, which are typically at the rear or base of the unit.
    3. Find the electrical junction box where the dishwasher’s wiring is connected to your home’s power supply.
    4. Open the junction box cover and thoroughly examine the wire connections for any visual evidence of burning, melting plastic, or dark discoloration on the wires or connectors.
    5. Confirm that the wire nuts or terminal screws are tight. A loose connection can generate excessive heat and is a fire hazard.
    6. Given the serious nature of an overheating main power connection, this issue must be repaired by a qualified electrician or a certified Bosch service to ensure safety and proper function.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E0107: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error E0110

    How to Fix Bosch Dishwasher Error E0110

    Error Code: E0110 Difficulty: Hard

    Problem: This error points to a failure in electronics communication.

    How to Fix E0110 Error (Step-by-Step)

    1. Begin by completely powering down the dishwasher. Press the power button to turn it off, then disconnect it from the power source by unplugging it from the wall outlet or switching off the corresponding circuit breaker.
    2. Leave the dishwasher without power for at least 15 minutes. This allows the internal electronics to fully reset and clear any temporary communication glitches.
    3. After waiting, restore power to the dishwasher. Turn the circuit breaker back on or plug the unit back into the outlet.
    4. For advanced troubleshooting, turn off the power at the circuit breaker again. You will need to access the main control board, typically located in the door panel. Remove the screws holding the inner door panel to the outer panel.
    5. With the inner panel removed, carefully inspect the wiring connected to the main control board. Ensure all plugs and harnesses are securely seated in their sockets. Look for any signs of loose wires, corrosion on the pins, or moisture.
    6. If all connections appear secure and dry, the fault likely lies within the electronic components themselves. This type of repair requires specialized check equipment and expertise. It is recommended to schedule a service appointment with a qualified Bosch service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E0110: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error E2030

    How to Fix Bosch Dishwasher Error E2030

    Error Code: E2030 Difficulty: Hard

    Problem: This code signifies a fault with the circulation motor or an internal heater fault within the heat pump.

    How to Fix E2030 Error (Step-by-Step)

    1. Disconnect the dishwasher from power at the circuit breaker and shut off the water supply valve under the sink. Place towels on the floor as some water will spill.
    2. Carefully pull the dishwasher out from under the counter. You may need to unscrew mounting brackets that secure it to the countertop.
    3. Lay the dishwasher on its back to access the components on the bottom. You will see the heat pump and circulation motor assembly in the center.
    4. Take a photo of the wire and hose connections for reference. Carefully disconnect the electrical connectors from the heat pump. Then, use pliers to release the clamps on the hoses and pull them off the pump assembly.
    5. Unfasten the mounting brackets or straps holding the heat pump in place. The old pump may need to be twisted or carefully pried to remove it from the dishwasher sump.
    6. Install the new heat pump assembly, making sure it is seated securely. Reconnect the hoses and tighten the clamps. Reattach the electrical connectors to their correct terminals based on your photo.
    7. Carefully set the dishwasher upright, slide it back into place, and reconnect the power and water. Run a test cycle to check for leaks and ensure the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E2030: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error E2120

    How to Fix Bosch Dishwasher Error E2120

    Error Code: E2120 Difficulty: Hard

    Problem: Indicates an interruption in the Zeolite heater heating circuit. The dishwasher will operate without the Zeolite drying system.

    How to Fix E2120 Error (Step-by-Step)

    1. Disconnect the dishwasher from power by turning off the circuit breaker and shut off the water supply valve, typically located under the sink. Place a towel on the floor to catch any residual water.
    2. Unscrew the mounting brackets that secure the dishwasher to the underside of the countertop. Carefully and slowly slide the dishwasher out from its cabinet. You may need to lower the adjustable feet to gain clearance.
    3. To access the necessary components, gently lay the dishwasher on its back or side on top of a blanket or cardboard to protect the floor and the unit.
    4. Locate the Zeolite container and the attached heater/temperature sensor assembly (part 00165281) at the base of the dishwasher, usually connected to the sump. Disconnect the wire harness attached to the sensor.
    5. The sensor is typically held in place by a retaining clip or by a twist-lock mechanism. Carefully release the clip or twist the sensor counter-clockwise to remove it from its housing. Be prepared for a small amount of water to spill out.
    6. Install the new sensor by pressing or twisting it firmly into place, making sure any o-rings or seals are properly seated to create a watertight connection. Reconnect the electrical wire harness.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E2120: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes

  • How to Fix Bosch Dishwasher Error E3000

    How to Fix Bosch Dishwasher Error E3000

    Error Code: E3000 Difficulty: Hard

    Problem: This error code points to a filling fault where there are no impulses from the flow sensor, even though water is detected by the heating pump.

    How to Fix E3000 Error (Step-by-Step)

    1. Disconnect the dishwasher from power by unplugging it or shutting off the circuit breaker.
    2. Turn off the water supply to the dishwasher from the valve under the sink.
    3. To access the components, you will likely need to pull the dishwasher out from under the counter. Place a towel on the floor and carefully lay the dishwasher on its back.
    4. Locate the flow sensor (part 00611317 or 00424099). It is typically part of the water inlet assembly where the main water line connects to the machine.
    5. Disconnect the wire harness from the old flow sensor. Have a towel ready to catch any residual water and disconnect the water hoses attached to it.
    6. Install the new flow sensor by connecting the water hoses and plugging in the wire harness. Ensure all connections are secure to prevent leaks.
    7. Carefully set the dishwasher upright, slide it back into place, reconnect the main water supply line, and restore power. Run a test cycle to confirm the error is resolved and check for any leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E3000: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Bosch error codes: Bosch Error Codes