Category: Bosch

  • How to Fix Bosch Dishwasher Error E24

    How to Fix Bosch Dishwasher Error E24

    Error Code: E24 Difficulty: Easy

    Problem: Dishwasher not draining properly due to a blocked drain filter.

    How to Fix E24 Error (Step-by-Step)

    1. Open the dishwasher door and completely remove the bottom dish rack to get clear access to the floor of the tub.
    2. Locate the filter system in the bottom center of the dishwasher. It consists of a cylindrical coarse filter and a flat fine mesh screen.
    3. Twist the cylindrical filter counter-clockwise and lift it straight up to remove it.
    4. Lift out the flat mesh screen that was underneath the cylindrical filter.
    5. Thoroughly rinse both filter components under warm, running water. Use a soft brush to gently remove any food debris or buildup.
    6. Check the sump area where the filters sit for any foreign objects and clean it out.
    7. Place the fine mesh screen back first, ensuring it lies flat, then insert and twist the cylindrical filter clockwise until it locks firmly into place.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E18

    How to Fix Bosch Dishwasher Error E18

    Error Code: E18 Difficulty: Hard

    Problem: Low water level or issue with water flow.

    How to Fix E18 Error (Step-by-Step)

    1. Turn off the dishwasher by pressing the power button, then shut off the circuit breaker dedicated to the appliance. For safety, also close the main water supply valve, usually located under the sink.
    2. Check the water supply hose connected to the back of the dishwasher. Ensure it is not bent, kinked, or crushed, as this can restrict water flow.
    3. Place a shallow pan and a towel under the water inlet valve connection at the dishwasher. Unscrew the supply hose and inspect the small filter screen inside the valve’s port. Clean any debris or mineral buildup from the screen using a small brush.
    4. To inspect internal components, remove the screws holding the front access panel at the bottom of the dishwasher. The water inlet valve (part 00631200) is typically on the front left side. Check its wire connections and look for any visible cracks or damage.
    5. Locate the flow meter (part 00620774), which is often near the inlet valve assembly. Ensure its wiring is secure and there are no visible signs of damage or blockages in the connected tubes.
    6. Inside the dishwasher, remove the bottom rack and unscrew the filter assembly in the sump area. Clear any food debris and check the drain pump cover. Remove the cover (it may twist off or be held by a screw) and inspect the drain pump impeller (part of 00642239) to ensure it can spin freely and is not blocked by foreign objects.
    7. If these checks do not resolve the error, the inlet valve, flow meter, or drain pump may be faulty and require electrical testing with a multimeter. Due to the complexity and risk of water damage, it is recommended to have a qualified service diagnose and replace the necessary components.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E16 / E17

    How to Fix Bosch Dishwasher Error E16 / E17

    Error Code: E16 / E17 Difficulty: Hard

    Problem: Issue with water flowing into the dishwasher or the filling system.

    How to Fix E16 / E17 Error (Step-by-Step)

    1. For safety, switch off the power to the dishwasher at your home’s circuit breaker and close the water supply valve.
    2. Gently pull the dishwasher out from under the counter to access the water connections, typically on the left side.
    3. Locate the water inlet valve, which is where the main water supply hose connects to the appliance.
    4. Place a towel under the valve to catch any water, then disconnect the main supply hose, the internal dishwasher hose, and the electrical wire connectors.
    5. Unscrew the mounting bracket that holds the old valve in place and remove it.
    6. Install the new water inlet valve, making sure to securely reattach all hoses and electrical connections.
    7. Turn the water and power back on, then start a wash program to verify that the dishwasher fills correctly and there are no leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E16 / E17: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal option/status indicator or a recurring fault that interrupts filling, washing, draining, drying, locking, or controls.
    3. 3. Treat E16 and E17 as related water-fill clues on this grouped Bosch dishwasher page: verify supply pressure, inlet screen, hose routing, float movement, inlet valve wiring, and whether the fault appears before wash circulation begins.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch the exact stage where the symptom returns; the stage matters more than the label by itself.
    6. 6. Replace a part only after the same symptom repeats and model-specific checks point to that part category. Match any replacement to the complete Bosch dishwasher model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the appliance tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E15

    How to Fix Bosch Dishwasher Error E15

    Error Code: E15 Difficulty: Hard

    Problem: Water leak detected in the base, activating the safety switch.

    How to Fix E15 Error (Step-by-Step)

    1. Turn off power to the dishwasher at the circuit breaker and shut off the water supply valve, typically located under the kitchen sink. Place old towels on the floor in front of the unit to catch any water.
    2. Carefully slide the dishwasher out from under the counter. You may first need to remove two mounting screws that secure the dishwasher to the underside of the countertop.
    3. With the dishwasher partially pulled out, gently tilt the unit forward or backward about 45 degrees to allow the water collected in the base pan to drain out onto the towels. This step is necessary to reset the anti-flood safety switch.
    4. Lay the dishwasher on its back to get clear access to the components underneath. Locate the drain pump (Part: 00631200), which is a common source of leaks.
    5. Disconnect the electrical wire connector attached to the drain pump. Place a shallow pan underneath to catch residual water, then twist the old pump counter-clockwise to unlock and remove it from the sump housing.
    6. Align the tabs on the new drain pump with the slots in the sump housing. Push the new pump in firmly and twist it clockwise until it locks securely into place. Reconnect the wire connector to the new pump.
    7. Carefully return the dishwasher to its upright position, slide it back into the cabinet, and secure the mounting screws. Reconnect the power and water supply, then run a short wash cycle to confirm the leak is fixed and the E15 error does not return.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E14

    How to Fix Bosch Dishwasher Error E14

    Error Code: E14 Difficulty: Hard

    Problem: Flow meter failure or an issue with water flowing into the dishwasher.

    How to Fix E14 Error (Step-by-Step)

    1. Disconnect the dishwasher from its power source at the circuit breaker and shut off the water supply line, which is typically under the sink.
    2. Carefully slide the dishwasher out from under the counter. You may need to remove mounting screws holding it to the countertop or adjacent cabinets.
    3. Remove the left-side access panel of the dishwasher. This usually involves removing a few Torx T20 screws from the front and back of the panel.
    4. Locate the flow meter, which is part of the water inlet assembly on the side of the dishwasher. It will have a small electrical connector attached.
    5. Disconnect the electrical connector from the old flow meter. Use a small flathead screwdriver to gently pry the plastic clips holding the meter in place and lift it out.
    6. Install the new flow meter by snapping it into place, ensuring the clips engage securely. Reconnect the electrical connector to the new part.
    7. Re-install the side panel, slide the dishwasher back into place, and secure it. Reconnect the power and water supply, then run a test cycle to ensure the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E13

    How to Fix Bosch Dishwasher Error E13

    Error Code: E13 Difficulty: Hard

    Problem: The water temperature is too high (above 75°C).

    How to Fix E13 Error (Step-by-Step)

    1. Disconnect the dishwasher from power by unplugging it or switching off the circuit breaker. Turn off the water supply valve, usually located under the sink.
    2. Carefully pull the dishwasher out from under the counter. You may need to disconnect the drain hose and water inlet line from the house plumbing first. Have a towel ready for any water that may spill.
    3. Gently lay the dishwasher on its back to access the bottom panel. Locate the NTC temperature sensor, which is part of the heater assembly at the base of the tub.
    4. Disconnect the wire harness connected to the sensor. Note the orientation of the wires before disconnecting.
    5. Remove the old sensor. It is typically held in place by a clip or by twisting it out of the heater assembly. Be prepared for a small amount of water to drain out.
    6. Install the new NTC sensor (part 00165281), ensuring it is securely seated and the O-ring creates a good seal. Reconnect the wire harness.
    7. Carefully set the dishwasher upright, slide it back into place, and reconnect the water supply and drain hose. Restore power, then run a test cycle to ensure the error is resolved and there are no leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E11

    How to Fix Bosch Dishwasher Error E11

    Error Code: E11 Difficulty: Hard

    Problem: Fault with the thermostat or temperature sensor (NTC Thermistor).

    How to Fix E11 Error (Step-by-Step)

    1. Disconnect the dishwasher from power and water. Turn off the circuit breaker for the dishwasher and shut off the water supply valve, usually located under the sink.
    2. Pull the dishwasher out from under the counter. You may need to remove the mounting screws that secure it to the countertop or cabinets first.
    3. Carefully tilt the dishwasher onto its back to access the components underneath. Place a towel down to protect the floor and the appliance.
    4. Locate the temperature sensor (NTC thermistor). It is typically found in the sump area at the bottom of the tub or attached to the heater assembly.
    5. Disconnect the wire harness from the old sensor. The sensor is usually held in place by a clip or a small turn-to-lock mechanism. Remove it from its housing.
    6. Install the new temperature sensor, ensuring it is securely seated and the O-ring creates a good seal. Reconnect the wire harness.
    7. Carefully set the dishwasher upright, slide it back into place, and reconnect the power and water supply before testing with a wash cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    What to Check Next on This Bosch Dishwasher

    temperature or heating fault: This code path generally needs temperature-sensing and heating checks, not a reset-only answer.

    1. Power the dishwasher off before checking harness connections at the heater, temperature sensor, and control area.
    2. Confirm the dishwasher fills and circulates, since the heater may be disabled if water movement is not correct.
    3. If the code returns, test the NTC/temperature sensor, heater circuit, wiring continuity, and control output in that order.

    If the symptom returns after these checks, use the full Bosch model number from the door tag before ordering any part. The same display message can point to different parts depending on the exact model and what the dishwasher does during fill, wash, drain, or dry.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error E08

    How to Fix Bosch Dishwasher Error E08

    Error Code: E08 Difficulty: Easy

    Problem: Loss of water during a cycle. The water level has dropped unexpectedly.

    How to Fix E08 Error (Step-by-Step)

    1. Press the ‘On/Off’ button to turn the dishwasher off and cancel the current cycle.
    2. Open the dishwasher door and check the position of the gray drain hose located under your sink.
    3. The drain hose must be looped up high, with the top of the loop secured as close to the underside of the countertop as possible. This creates a ‘high loop’.
    4. A proper high loop prevents water from the sink drain from flowing back into the dishwasher and also stops water from siphoning out of the tub during a cycle.
    5. If the hose is not looped high enough, reposition it and secure it in place with a zip tie or clamp.
    6. After confirming the high loop, close the dishwasher door, select a new wash cycle, and press ‘Start’ to see if the error is resolved.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error E08: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the fill path: water supply, inlet screen, hose position, float or level sensing, inlet valve wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error DRYING SYMBOL

    How to Fix Bosch Dishwasher Error DRYING SYMBOL

    Error Code: DRYING SYMBOL Difficulty: Easy

    Problem: Indicates that the dishwasher is in the drying phase of the wash cycle.

    How to Fix DRYING SYMBOL Error (Step-by-Step)

    1. Identify the ‘Drying’ symbol on your dishwasher’s display, which often looks like rays of sun or heat waves.
    2. Understand that this is a normal operational light indicating the dishwasher has finished washing and is now in the drying portion of its cycle.
    3. This symbol is not an error and requires no action from you.
    4. The dishwasher may use a heating element or condensation drying. The door may be hot to the touch if a heating element is active.
    5. Allow the dishwasher to complete the drying cycle for the best results. Opening the door early can result in wet dishes.
    6. The light will turn off, and the dishwasher will typically signal with a beep, once the entire cycle is complete.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error DRYING SYMBOL: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the heat and temperature path: water circulation, heater circuit, NTC sensor, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Bosch Dishwasher Error DELAY START SYMBOL

    How to Fix Bosch Dishwasher Error DELAY START SYMBOL

    Error Code: DELAY START SYMBOL Difficulty: Easy

    Problem: Allows the user to set a delayed start time for a wash cycle.

    How to Fix DELAY START SYMBOL Error (Step-by-Step)

    1. Recognize that the ‘Delay Start’ symbol (often a clock icon) means a wash cycle has been programmed to start at a later time. This is a feature, not an error.
    2. The display will typically show the number of hours remaining until the cycle begins.
    3. If you wish to cancel the delay and start the wash immediately, you will need to reset the function.
    4. Press and hold the ‘Start’ button on your dishwasher for about 3 to 5 seconds.
    5. This action should cancel the ‘Delay Start’ setting and reset the dishwasher. The ‘Delay Start’ symbol should disappear from the display.
    6. You can now select your desired wash cycle and press ‘Start’ again to begin the cleaning process right away.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Bosch dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Bosch dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for fill and water-supply faults after the tap, hose, and inlet screen are checked.

      Search Amazon for Bosch dishwasher water inlet valve

    • Bosch dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for drain and standing-water symptoms after the filter, sump, and hose are checked.

      Search Amazon for Bosch dishwasher drain pump

    • Bosch dishwasher circulation pump
      Common replacement category: Circulation pump / wash motor
      Fit note: Exact OEM part number varies by full Bosch dishwasher model number. Confirm compatibility before buying.
      Confidence: Medium
      This category can be relevant for wash, spray-arm, and circulation symptoms after filters and spray arms are checked.

      Search Amazon for Bosch dishwasher circulation pump

    Before ordering: match the part to the complete Bosch dishwasher model number on the appliance tag.

    What to Check Next on This Bosch Dishwasher

    Bosch Dishwasher Error DELAY START SYMBOL: Use the code, light, or symbol as the starting clue, then confirm what the dishwasher actually does before ordering parts.

    1. 1. Turn power off before opening panels, reaching into the sump, touching wiring, or checking the pump, heater, valve, sensor, latch, or control area.
    2. 2. Confirm whether the display is a normal cycle/status symbol or a recurring fault that interrupts filling, washing, draining, drying, locking, or control response.
    3. 3. Start with the wash path: filter, sump debris, spray-arm movement, circulation-pump sound, wiring, and control output.
    4. 4. Clean the filter and sump, check spray-arm movement, verify water supply, inspect the drain hose and sink connection, and correct any visible blockage before replacing parts.
    5. 5. Run a short test cycle and watch where it fails; the exact stage matters more than the displayed word or symbol by itself.
    6. 6. Replace a part only after the same symptom repeats and the model-specific checks point to that part category. Match any replacement to the complete Bosch model number on the door tag.

    If the issue returns after these checks, match replacement parts to the complete Bosch dishwasher model number from the door tag. The same display clue can point to different components depending on the exact model and when the failure appears.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


    Browse all Bosch error codes: Bosch Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.