Category: Dryer

  • How to Fix Bosch Dryer Error F01

    How to Fix Bosch Dryer Error F01

    Error Code: F01 Difficulty: Hard

    Problem: Faulty inlet valve.

    How to Fix F01 Error (Step-by-Step)

    1. Turn off the water supply and unplug the dryer and confirm the error stays cleared during a full test cycle.
    2. Access the rear of the dryer to locate the water inlet valve.
    3. Place a towel beneath the hoses to catch any residual water and then disconnect them from the valve.
    4. Remove the mounting screws that hold the inlet valve in place.
    5. Carefully disconnect the electrical wires from the old valve and confirm the error stays cleared during a full test cycle.
    6. Install the new inlet valve by securing it with the mounting screws and reconnecting the electrical wires.
    7. Reattach the water hoses, turn the water supply on, and check for leaks before plugging the dryer back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error F42

    How to Fix Bosch Dryer Error F42

    Error Code: F42 Difficulty: Hard

    Problem: Issue with the carbon brushes in the motor.

    How to Fix F42 Error (Step-by-Step)

    1. Disconnect the dryer from the power source and confirm the error stays cleared during a full test cycle.
    2. Remove the necessary panels to gain access to the dryer’s motor.
    3. Locate the carbon brushes on the motor housing and confirm the error stays cleared during a full test cycle.
    4. Disconnect the electrical leads attached to the brushes and confirm the error stays cleared during a full test cycle.
    5. Remove the screws or clips holding the old carbon brushes in place and remove them.
    6. Insert the new carbon brushes and secure them and confirm the error stays cleared during a full test cycle.
    7. Reconnect the electrical leads and reassemble the dryer and confirm the error stays cleared during a full test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error H32

    How to Fix Bosch Dryer Error H32

    Error Code: H32 Difficulty: Easy

    Problem: Unbalanced load.

    How to Fix H32 Error (Step-by-Step)

    1. Pause the drying cycle and wait for the drum to stop.
    2. Open the dryer door and look for any tangled or balled-up laundry.
    3. Untangle the items and redistribute them evenly inside the drum.
    4. Avoid overloading the dryer, as this can lead to unbalanced loads.
    5. If you are drying a single large item, add a few smaller items to help balance the load.
    6. Close the door and resume the drying cycle and confirm the error stays cleared during a full test cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error SQUARE WITH CIRCLE AND TWO DOTS

    How to Fix Bosch Dryer Error SQUARE WITH CIRCLE AND TWO DOTS

    Error Code: SQUARE WITH CIRCLE AND TWO DOTS Difficulty: Easy

    Problem: Normal drying at a regular temperature.

    How to Fix SQUARE WITH CIRCLE AND TWO DOTS Error (Step-by-Step)

    1. Locate this symbol on your dryer’s control panel. It indicates the ‘Normal’ or ‘Cottons’ drying setting, which uses a standard heat level.
    2. This is a standard cycle indicator, not an error message. It is intended for drying durable fabrics like cotton towels, jeans, and bedding.
    3. To activate this cycle, first power on the dryer and confirm the error stays cleared during a full test cycle.
    4. Rotate the main program dial to a cycle designed for robust fabrics, such as ‘Cottons’ or ‘Regular’.
    5. On models with a separate temperature selection, ensure the medium or high heat option (often indicated by this two-dot symbol) is selected.
    6. Place your regular laundry load into the drum, ensure the door is securely closed, and press the ‘Start’ button to run the normal drying cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You