Category: Dryer

  • How to Fix Bosch Dryer Error E02

    How to Fix Bosch Dryer Error E02

    Error Code: E02 Difficulty: Moderate

    Problem: Lint filter is still blocked or wet.

    How to Fix E02 Error (Step-by-Step)

    1. Unplug the dryer for at least 30 minutes to allow it to reset.
    2. Remove the lint filter and wash it with warm, soapy water and a soft brush to remove any fabric softener residue.
    3. Rinse the filter thoroughly and allow it to air dry completely before reinserting it.
    4. While the filter is drying, use a vacuum cleaner to clean the lint filter housing and the vent pipe connected to the back of the dryer.
    5. Ensure the venting hose is not kinked or crushed, and that the exterior vent flap is opening freely.
    6. Once everything is clean and dry, reassemble and plug the dryer back in.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E06

    How to Fix Bosch Dryer Error E06

    Error Code: E06 Difficulty: Hard

    Problem: Heating circuit fault.

    How to Fix E06 Error (Step-by-Step)

    1. Disconnect the dryer from the power supply completely and confirm the error stays cleared during a full test cycle.
    2. For this repair, you will need to access the back of the dryer by removing the rear panel.
    3. Locate the heating element assembly, which is a large metal housing containing the heating coils.
    4. Use a multimeter to test the continuity of the heating element. A reading of infinity indicates a broken element that needs replacement.
    5. Also, test the high-limit thermostat and thermal fuse, which are typically mounted on the heating element housing. These should have continuity.
    6. If any of these components fail the continuity test, the entire heating element assembly should be replaced.
    7. This is a complex repair and may be best left to a qualified service if you are not comfortable working with electrical components.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E08

    How to Fix Bosch Dryer Error E08

    Error Code: E08 Difficulty: Hard

    Problem: Electronics fault.

    How to Fix E08 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet.
    2. Remove the top panel of the dryer by unscrewing the screws holding it in place, typically located at the back.
    3. Locate the control board, which is usually at the front of the dryer behind the control panel.
    4. Carefully disconnect all the wire harnesses connected to the old control board, taking a photo beforehand for reference.
    5. Remove the screws that secure the control board to the dryer frame and gently lift it out.
    6. Install the new control board, making sure it is properly aligned and secured with the screws.
    7. Reconnect all the wire harnesses to the new control board according to your reference photo and then reassemble the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E09

    How to Fix Bosch Dryer Error E09

    Error Code: E09 Difficulty: Hard

    Problem: Electronics fault.

    How to Fix E09 Error (Step-by-Step)

    1. Turn off the power to the dryer at the circuit breaker and unplug the appliance.
    2. Access the control board by removing the top panel of the dryer, which is usually secured by screws at the back.
    3. Identify the control board, typically found behind the front control panel.
    4. Take a clear picture of the wire connections before disconnecting them from the control board.
    5. Unscrew the mounting screws holding the control board in place and carefully remove it.
    6. Position the new control board in the same location and secure it with the mounting screws.
    7. Reconnect the wires to the new board as per your photo, reattach the top panel, and restore power to the dryer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Bosch Dryer Error E11

    How to Fix Bosch Dryer Error E11

    Error Code: E11 Difficulty: Moderate

    Problem: Overheating, often due to a clogged lint filter or poor ventilation.

    How to Fix E11 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure safety.
    2. Locate the thermal fuse, which is typically on the blower housing or the heating element housing at the back of the dryer.
    3. Disconnect the two wires attached to the thermal fuse and confirm the error stays cleared during a full test cycle.
    4. Remove the screw that holds the thermal fuse in place and remove the old fuse.
    5. Secure the new thermal fuse with the mounting screw and confirm the error stays cleared during a full test cycle.
    6. Reconnect the two wires to the new thermal fuse and confirm the error stays cleared during a full test cycle.
    7. Before reassembling, thoroughly clean the lint filter, the dryer vent, and the exhaust duct to prevent future overheating.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error E12

    How to Fix Bosch Dryer Error E12

    Error Code: E12 Difficulty: Moderate

    Problem: Severe overheating, typically due to a blocked lint filter or exhaust vent.

    How to Fix E12 Error (Step-by-Step)

    1. Disconnect the dryer from its power source by unplugging it.
    2. Access the back of the dryer and locate the thermal fuse on the heating element or blower housing.
    3. Carefully detach the wires connected to the fuse and confirm the error stays cleared during a full test cycle.
    4. Unscrew the thermal fuse from its mounting and remove it.
    5. Install the new thermal fuse and secure it with the screw.
    6. Reattach the wires to the terminals of the new fuse.
    7. It is critical to clean the entire venting system, from the lint screen to the outside exhaust vent, to address the cause of the severe overheating.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error E13

    How to Fix Bosch Dryer Error E13

    Error Code: E13 Difficulty: Hard

    Problem: Maximum drying time exceeded.

    How to Fix E13 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the rear panel of the dryer to access the heating element assembly.
    3. Disconnect the wires from the heating element and the high-limit thermostat.
    4. Remove the screws holding the heating element assembly in place and slide it out.
    5. Install the new heating element assembly and secure it with the screws.
    6. Reconnect the wires to the new element and thermostat and confirm the error stays cleared during a full test cycle.
    7. If the issue persists, the thermistor or control boards may need to be replaced by a professional.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Display Control Board
    • Thermistor (NTC Sensor)
    • Heating Element Assembly

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error E17

    How to Fix Bosch Dryer Error E17

    Error Code: E17 Difficulty: Moderate

    Problem: Lint screen temperature sensor (NTC) error.

    How to Fix E17 Error (Step-by-Step)

    1. Disconnect the power to the dryer by unplugging it and confirm the error stays cleared during a full test cycle.
    2. The lint screen NTC sensor is located in the lint filter housing. Remove the lint screen to access it.
    3. You may need to remove the top or front panel to get to the sensor’s wiring.
    4. Disconnect the wire connector from the NTC sensor and confirm the error stays cleared during a full test cycle.
    5. Remove the screw or clip holding the sensor in place and remove the old sensor.
    6. Install the new NTC sensor and secure it and confirm the error stays cleared during a full test cycle.
    7. Reconnect the wire connector, reassemble the dryer, and restore power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error E18

    How to Fix Bosch Dryer Error E18

    Error Code: E18 Difficulty: Moderate

    Problem: Heater temperature sensor (NTC) error.

    How to Fix E18 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Locate the heater NTC sensor, which is typically mounted on the heating element housing at the back of the dryer.
    3. To access it, you will likely need to remove the rear panel of the dryer.
    4. Disconnect the wiring from the sensor and confirm the error stays cleared during a full test cycle.
    5. Remove the screw that secures the sensor and take out the old sensor.
    6. Place the new NTC sensor in the same position and fasten it with the screw.
    7. Reconnect the wiring, replace the rear panel, and plug the dryer back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dryer Error E20

    How to Fix Bosch Dryer Error E20

    Error Code: E20 Difficulty: Hard

    Problem: Unexpected heating.

    How to Fix E20 Error (Step-by-Step)

    1. Turn off the dryer and unplug it from the wall outlet for safety.
    2. Wait for at least 10 minutes to allow all electronic components to fully discharge and reset.
    3. While waiting, thoroughly clean the lint filter by removing all visible lint and washing it with warm, soapy water to remove any residue.
    4. Check the dryer’s exhaust vent hose at the back and the vent opening outside your home for any blockages or restrictions. Clear any lint buildup you find.
    5. After 10 minutes, plug the dryer back in and attempt to run a cycle.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You