Category: Washer

  • How to Fix Amana Washer Error F3 E1

    How to Fix Amana Washer Error F3 E1

    Error Code: F3 E1 Difficulty: Hard

    Problem: Pressure System Fault

    How to Fix F3 E1 Error (Step-by-Step)

    1. Unplug the washer from the electrical outlet to ensure safety.
    2. Turn off both the hot and cold water supply valves connected to the washer.
    3. Locate the main control board, which is typically found inside the top console panel.
    4. Take a photo of the wire connections for reference, then carefully disconnect all wire harnesses from the old control board.
    5. Remove the screws or release the clips holding the old board in place and gently remove it.
    6. Install the new main control board, securing it with the original screws or clips.
    7. Reconnect all wire harnesses to the correct terminals on the new board, using your photo as a guide.
    8. Reassemble the console, restore power, and run a test cycle to ensure the fault is cleared.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F2E4

    How to Fix Amana Washer Error F2E4

    Error Code: F2E4 Difficulty: Hard

    Problem: Issue with the user interface or associated wiring.

    How to Fix F2E4 Error (Step-by-Step)

    1. If the code returns, unplug the machine again. You will need to access the control console area.
    2. Remove the screws holding the top panel or console in place. This is usually done from the back or sides of the console.
    3. Once you have access, carefully inspect the wire harness that connects the main control board to the user interface board. Ensure the connector is plugged in securely and that no wires are damaged or pinched.
    4. If the wiring looks good, the user interface board itself is the most likely cause of the problem.
    5. Take a picture of the wire connections. Disconnect the wires and remove the screws holding the old board.
    6. Install the new user interface board, reconnect the wires based on your picture, and reassemble the console.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F22

    How to Fix Amana Washer Error F22

    Error Code: F22 Difficulty: Moderate

    Problem: Door Lock Error

    How to Fix F22 Error (Step-by-Step)

    1. Unplug the washing machine from its power source and confirm the error stays cleared during a full test cycle.
    2. Open the washer door. The door lock assembly is located on the front frame of the washer, where the door latch engages.
    3. To access it, you must peel back the large rubber door seal (bellow). Find the outer wire spring clamp holding the bellow in place and carefully pry it off with a flathead screwdriver.
    4. With the clamp removed, peel the bellow away from the frame in the area of the door lock.
    5. You will now see the screws that secure the door lock assembly. Remove these screws.
    6. Reach in and pull the lock assembly out. Take a photo of the wire connector, then disconnect it.
    7. Connect the new door lock, mount it in place with the screws, and carefully re-secure the rubber bellow with its spring clamp.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F21

    How to Fix Amana Washer Error F21

    Error Code: F21 Difficulty: Moderate

    Problem: Long Drain

    How to Fix F21 Error (Step-by-Step)

    1. Check the washer’s drain hose for any clogs or kinks. Ensure it is not sealed into the house standpipe, as it needs an air gap to drain properly.
    2. Unplug the washer. Prepare for water to spill by placing towels and a shallow pan on the floor.
    3. Most Amana front-loaders have a small access door at the bottom-front of the machine. Open it to find the drain pump filter cap.
    4. Slowly twist the cap counter-clockwise to drain the remaining water into your pan. Once drained, fully remove the cap.
    5. Clean out any debris from the filter, such as lint, coins, or buttons. Also, check inside the pump housing for any obstructions.
    6. If the filter is clear and the washer still won’t drain, the drain pump is likely defective and needs to be replaced.
    7. Disconnect the hoses and electrical connector from the old pump, remove it, and install the new one, then reassemble.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F20

    How to Fix Amana Washer Error F20

    Error Code: F20 Difficulty: Moderate

    Problem: No Water Detected

    How to Fix F20 Error (Step-by-Step)

    1. First, ensure the water supply faucets behind the washer are turned on completely.
    2. Check the water inlet hoses for any kinks or twists that could block water flow. Straighten them if necessary.
    3. Unplug the washer and turn off the water faucets. Unscrew the hoses from the back of the machine.
    4. Inside the connection ports on the washer, you will find small filter screens. Use pliers to gently pull them out and clean any sediment or debris under a faucet. Reinstall them.
    5. If the screens are clean and the problem continues, the water inlet valve is likely faulty. Remove the washer’s back or top panel to access it.
    6. Take a photo of the electrical connectors and hoses attached to the valve.
    7. Disconnect the wires and hoses, remove the mounting screws, and install the new valve. Reconnect everything and turn the water and power back on.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F2 E1

    How to Fix Amana Washer Error F2 E1

    Error Code: F2 E1 Difficulty: Hard

    Problem: Stuck Key

    How to Fix F2 E1 Error (Step-by-Step)

    1. Perform a hard reset by unplugging the washer for at least 5 minutes. Plug it back in and test if the error is gone.
    2. If the error persists, unplug the washer again. You will need to access the user interface board in the main control console.
    3. To do this, you may need to remove screws from the back of the console or top panel of the washer to tilt or remove it.
    4. Take a clear photograph of the wiring connected to the user interface board.
    5. Disconnect the ribbon cables and any other wire harnesses from the old board.
    6. Remove the screws holding the user interface in place and swap it with the new part.
    7. Reconnect all wiring using your photo as a reference, reassemble the console, and restore power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Main Control Board

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F1 E1

    How to Fix Amana Washer Error F1 E1

    Error Code: F1 E1 Difficulty: Hard

    Problem: Main Control Fault

    How to Fix F1 E1 Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure safety.
    2. Turn off both the hot and cold water supply valves connected to the washer.
    3. Locate the main control board. This is typically found inside the top console panel or on the back of the machine.
    4. Take a clear picture of the wire connections to the board before you disconnect anything. This will be your guide for installation.
    5. Carefully disconnect all wiring harnesses from the old control board. Most connectors have a small locking tab you need to press.
    6. Remove the screws or release the clips holding the old board in place and gently lift it out.
    7. Install the new main control board, secure it, and reconnect all wiring harnesses by referring to the photo you took.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0E9

    How to Fix Amana Washer Error F0E9

    Error Code: F0E9 Difficulty: Hard

    Problem: Unbalanced load.

    How to Fix F0E9 Error (Step-by-Step)

    1. Unplug the washer and turn off the water supply lines.
    2. Use a putty knife to press in and release the two clips located in the seam between the top and front panels. Hinge the top panel up and back.
    3. You will see four suspension rods, one at each corner, supporting the wash tub.
    4. Working on one corner at a time, slightly lift the tub to relieve tension. Unhook the top of the suspension rod from the tub support, then pull the entire rod assembly up and out of the washer base.
    5. Guide the new suspension rod down into the base, ensuring it is properly seated. Lift the tub again and hook the top of the new rod into place.
    6. Repeat this process for the remaining three rods, replacing them one by one.
    7. Lower the top panel, press down to secure the clips, reconnect power and water, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0E8

    How to Fix Amana Washer Error F0E8

    Error Code: F0E8 Difficulty: Moderate

    Problem: Too much residual water has been detected in the washer.

    How to Fix F0E8 Error (Step-by-Step)

    1. Unplug the washer from its power source and turn off the water supply valves.
    2. Place towels on the floor and carefully tilt the washer forward, resting it against a wall for stability to access the bottom.
    3. Locate the drain pump, which is a small component with two large hoses attached.
    4. Put a shallow pan underneath the hoses to catch water. Use pliers to squeeze the clamps on the hoses and slide them off the pump ports.
    5. Disconnect the electrical wire connector from the pump and confirm the error stays cleared during a full test cycle.
    6. Remove the mounting screws that hold the old pump in place and take it out.
    7. Install the new pump, secure it with the screws, and reattach the hoses, clamps, and electrical connector before carefully returning the washer to its upright position.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F0E7

    How to Fix Amana Washer Error F0E7

    Error Code: F0E7 Difficulty: Easy

    Problem: Items were detected in the washer during the Clean Washer cycle.

    How to Fix F0E7 Error (Step-by-Step)

    1. Press the ‘Power’ button to cancel the ‘Clean Washer’ cycle.
    2. Open the washer lid and look inside the drum and confirm the error stays cleared during a full test cycle.
    3. Remove any forgotten items such as clothes, towels, or other laundry.
    4. The ‘Clean Washer’ cycle is meant to clean the inside of the machine and must be run completely empty.
    5. Close the lid securely and confirm the error stays cleared during a full test cycle.
    6. Select the ‘Clean Washer’ cycle again and press ‘Start’ with the now-empty drum.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes