Category: Refrigerator

How to Fix Amana Refrigerator Error AIR FILTER INDICATOR LIGHT
Error Code: AIR FILTER INDICATOR LIGHT Difficulty: Easy

Problem: Indicates the status of the air filter.

How to Fix AIR FILTER INDICATOR LIGHT Error (Step-by-Step)
1. Locate the air filter housing inside the refrigerator. It’s typically a small, vented compartment on the upper back wall.
2. Open the filter housing. This may require pressing a tab or sliding the cover.
3. Remove the old air filter and discard it and confirm the error stays cleared during a full test cycle.
4. Insert the new air filter into the housing, ensuring it is positioned correctly.
5. Close the filter housing securely and confirm the error stays cleared during a full test cycle.
6. Reset the air filter indicator light by pressing and holding the ‘Filter’ or ‘Reset’ button for three seconds.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error C
Error Code: C Difficulty: Hard

Problem: Temperature or Sensor Error.

How to Fix C Error (Step-by-Step)
1. Unplug the refrigerator from the power outlet for safety and confirm the error stays cleared during a full test cycle.
2. Locate the thermistor inside the fresh food compartment. It is usually found near the top, behind a small plastic cover.
3. Carefully remove the cover to expose the thermistor. You may need a small screwdriver.
4. Disconnect the wire harness attached to the old thermistor and confirm the error stays cleared during a full test cycle.
5. Remove the old thermistor from its mounting clip and confirm the error stays cleared during a full test cycle.
6. Install the new thermistor by snapping it into the mounting clip and reconnecting the wire harness.
7. Replace the cover, plug the refrigerator back in, and monitor for normal operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error CF
Error Code: CF Difficulty: Easy

Problem: Control Board or Keypad Error.

How to Fix CF Error (Step-by-Step)
1. Locate the water filter, which is typically in the grille at the base of the refrigerator or inside the upper right corner of the fresh food compartment.
2. If in the grille, turn the filter cap counterclockwise to a vertical position and pull it out.
3. If inside the refrigerator, there may be a push-button or a twist-off cap to release the filter.
4. Remove the old filter by pulling it straight out and confirm the error stays cleared during a full test cycle.
5. Align the new filter with the housing and push it in until it clicks into place.
6. If applicable, turn the filter cap clockwise to a horizontal position.
7. Run about two gallons of water through the dispenser to flush the new filter.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error COOLING OFF INDICATOR LIGHT
Error Code: COOLING OFF INDICATOR LIGHT Difficulty: Easy

Problem: Indicates that the cooling function of the refrigerator is turned off.

How to Fix COOLING OFF INDICATOR LIGHT Error (Step-by-Step)
1. Locate the control panel on your refrigerator, usually on the dispenser or inside the fresh food compartment.
2. Look for a button labeled ‘Cooling On/Off’ or a similar variation.
3. Press and hold this button for three to five seconds.
4. You should hear a beep or see the indicator light turn off, confirming that the cooling function has been reactivated.
5. Allow the refrigerator several hours to return to its set temperature.
6. Turn the appliance off, wait about 2 minutes, then turn it back on.
7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error D7 ILLUMINATED
Error Code: D7 ILLUMINATED Difficulty: Hard

Problem: Main control board issue.

How to Fix D7 ILLUMINATED Error (Step-by-Step)
1. Disconnect the refrigerator from the power source to avoid electrical shock.
2. Locate the main control board, which is typically on the back of the refrigerator behind an access panel.
3. Remove the screws securing the access panel and set it aside.
4. Carefully disconnect all wire harnesses from the old control board, taking a picture beforehand can help with reassembly.
5. Remove the screws or release the locking tabs holding the old control board in place and remove it.
6. Install the new main control board, securing it with the screws or locking tabs.
7. Reconnect all wire harnesses to the appropriate terminals on the new board, referencing your picture if needed.
8. Replace the access panel and its screws, then plug the refrigerator back in.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error D7 AND D8 ILLUMINATED
Error Code: D7 AND D8 ILLUMINATED Difficulty: Hard

Problem: Main board and refrigerator sensor issue.

How to Fix D7 AND D8 ILLUMINATED Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet and confirm the error stays cleared during a full test cycle.
2. Access and replace the main control board located on the back of the unit behind a service panel.
3. Disconnect all wiring harnesses from the old board, remove it, and install the new one, ensuring all connections are secure.
4. Locate the refrigerator sensor (thermistor) inside the fresh food compartment, usually behind a small cover on the back wall or ceiling.
5. Remove the cover, disconnect the old sensor, and remove it from its clip.
6. Install the new sensor, reconnect its wiring, and replace the cover.
7. Reassemble the service panel, plug the refrigerator in, and check if the error codes have cleared.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- Refrigerator Sensor (Thermistor)
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error D7 AND D9 ILLUMINATED
Error Code: D7 AND D9 ILLUMINATED Difficulty: Hard

Problem: Main board and defrost sensor issue.

How to Fix D7 AND D9 ILLUMINATED Error (Step-by-Step)
1. Ensure the refrigerator is unplugged from the power source and confirm the error stays cleared during a full test cycle.
2. Replace the main control board, which is found on the back of the refrigerator behind an access panel.
3. Carefully transfer all wire connections from the old board to the new one.
4. Locate the defrost sensor, which is clipped to the evaporator coils in the freezer section. This will require removing the back panel inside the freezer.
5. Disconnect the old defrost sensor and unclip it from the evaporator coil.
6. Clip the new defrost sensor in the same location and reconnect its wiring.
7. Reinstall the freezer panel and the main control board access panel, then restore power to the refrigerator.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- Main Control Board
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error D7, D8, AND D9 ILLUMINATED
Error Code: D7, D8, AND D9 ILLUMINATED Difficulty: Hard

Problem: Multiple sensor failures.

How to Fix D7, D8, AND D9 ILLUMINATED Error (Step-by-Step)
1. Disconnect the refrigerator from its power supply and confirm the error stays cleared during a full test cycle.
2. Begin by replacing the main control board located on the rear of the appliance behind a service panel.
3. Next, replace the refrigerator sensor (thermistor) located within the fresh food section.
4. Then, access the freezer compartment and remove the interior back panel to locate and replace the defrost sensor on the evaporator coils.
5. After replacing all three components, reassemble the freezer panel and the rear service panel.
6. Plug the refrigerator back into the power outlet and monitor for the disappearance of the error codes.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- Main Control Board
- Refrigerator Sensor (Thermistor)
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error D8 ILLUMINATED
Error Code: D8 ILLUMINATED Difficulty: Moderate

Problem: Refrigerator sensor issue.

How to Fix D8 ILLUMINATED Error (Step-by-Step)
1. Unplug the refrigerator from the wall outlet to ensure safety.
2. Locate the refrigerator sensor, also known as a thermistor. It is typically found inside the fresh food compartment, clipped to a vent or along the side or back wall.
3. Carefully remove any screws or release any clips that hold the sensor’s cover in place.
4. Disconnect the small wire harness attached to the old sensor. Do not pull on the wires themselves.
5. Connect the new sensor to the wire harness and secure it in the same location as the old one.
6. Replace the cover, plug the refrigerator back in, and allow a few hours for the temperature to stabilize.
7. Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026
How to Fix Amana Refrigerator Error D8 AND D9 ILLUMINATED
Error Code: D8 AND D9 ILLUMINATED Difficulty: Hard

Problem: Refrigerator and defrost sensor issue.

How to Fix D8 AND D9 ILLUMINATED Error (Step-by-Step)
1. Disconnect the refrigerator from its power source to prevent electrical shock.
2. First, replace the refrigerator sensor (thermistor) located in the fresh food section by following the steps for the ‘D8’ error code.
3. Next, empty the freezer compartment and remove the screws holding the interior back panel.
4. Carefully detach the panel to expose the evaporator coils. The defrost sensor is a small component clipped directly onto the evaporator tubing.
5. Unplug the wire connector for the old defrost sensor and remove it from the clip.
6. Install the new defrost sensor by clipping it onto the tubing and reconnecting the wire harness.
7. Reinstall the freezer’s back panel, restore power to the unit, and monitor for normal operation.
8. Turn the appliance off, wait about 2 minutes, then turn it back on.
Verified Compatible Alternatives:
- Refrigerator Sensor (Thermistor)
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Browse all Amana error codes: Amana Error Codes
April 23, 2026