Category: Amana

  • How to Fix Amana Dishwasher Error LDL

    How to Fix Amana Dishwasher Error LDL

    Error Code: LDL Difficulty: Easy

    Problem: Lid will not lock.

    How to Fix LDL Error (Step-by-Step)

    1. Open the dishwasher door and check for any items, such as utensils or a dishrack, that may be blocking the door from closing completely.
    2. Inspect the door latch area at the top of the dishwasher tub. Clean away any food debris or residue with a damp cloth.
    3. Examine the strike plate on the door that engages with the latch. Ensure it is not bent or damaged.
    4. Close the door firmly and ensure you hear a distinct ‘click’ sound, indicating the latch has engaged.
    5. As a reset, turn off the power to the dishwasher at the circuit breaker for 5 minutes, then turn it back on.
    6. Try to start a new cycle. If the door still fails to lock, the latch assembly may need to be inspected by a service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error LDU

    How to Fix Amana Dishwasher Error LDU

    Error Code: LDU Difficulty: Hard

    Problem: Lid will not unlock.

    How to Fix LDU Error (Step-by-Step)

    1. First, cancel any active cycle and try to start a new one. Sometimes the control board needs to reset to release the lock.
    2. Turn off power to the dishwasher by switching off the corresponding circuit breaker in your home’s electrical panel. Wait for 5-10 minutes before restoring power.
    3. After restoring power, try to open the door. This power cycle can often reset the lock mechanism.
    4. If the door remains locked, you will need to replace the door latch assembly. This requires accessing the inner door panel.
    5. With the power still off, remove the screws holding the inner door panel to the outer panel. These are usually located around the perimeter of the inner door.
    6. Carefully separate the panels to expose the latch assembly. Disconnect the wiring harness connected to the latch.
    7. Remove the screws holding the old latch in place, install the new latch, and reconnect the wiring. Reassemble the door panels before restoring power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10274884
    • WPW10130695

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error LID

    How to Fix Amana Dishwasher Error LID

    Error Code: LID Difficulty: Moderate

    Problem: Lid is open.

    How to Fix LID Error (Step-by-Step)

    1. Turn the appliance off to the dishwasher at your home’s circuit breaker or fuse box.
    2. Open the dishwasher door and locate the screws around the edge of the inner door panel.
    3. Using a screwdriver, remove all the screws holding the inner panel to the outer door.
    4. Carefully separate the inner and outer door panels to expose the door latch and switch assembly at the top of the door.
    5. Disconnect the wire harness connected to the door switch and confirm the error stays cleared during a full test cycle.
    6. Remove the screws holding the old latch assembly in place and install the new one.
    7. Reconnect the wire harness, reassemble the door panels, and restore power to test the dishwasher.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10274884
    • WPW10130695

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error PF

    How to Fix Amana Dishwasher Error PF

    Error Code: PF Difficulty: Easy

    Problem: Power failure.

    How to Fix PF Error (Step-by-Step)

    1. First, check that the dishwasher’s power cord is securely plugged into the wall outlet.
    2. Go to your home’s electrical panel and check if the circuit breaker for the dishwasher has tripped. If it has, flip it completely off and then back on.
    3. If you have a fuse box, check for a blown fuse and replace it if necessary.
    4. Ensure the dishwasher door is fully closed and latched shut. The dishwasher will not start if the door is ajar.
    5. Press the ‘Start/Resume’ button to begin a new cycle.
    6. If the power failure was brief, the dishwasher might resume its cycle automatically after a few minutes.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error SANITIZE LIGHT FLASHING

    How to Fix Amana Dishwasher Error SANITIZE LIGHT FLASHING

    Error Code: SANITIZE LIGHT FLASHING Difficulty: Moderate

    Problem: The water is not hot enough to sanitize the dishes.

    How to Fix SANITIZE LIGHT FLASHING Error (Step-by-Step)

    1. Before starting a cycle, run the hot water at the kitchen sink for a minute until it is hot. This ensures the dishwasher fills with hot water from the start.
    2. Check your home’s water heater settings. The temperature should be set to at least 120°F (49°C) for the dishwasher to sanitize properly.
    3. Turn the appliance off to the dishwasher at the circuit breaker.
    4. To access the heating element, you may need to pull the dishwasher out from under the counter. The element is a circular tube at the bottom of the dishwasher tub.
    5. Visually inspect the heating element for any signs of damage or breaks. You can test it for continuity with a multimeter.
    6. Locate the high-limit thermostat, usually mounted on the bottom of the tub. Test it for continuity as well.
    7. If either the heating element or thermostat is faulty, it will need to be replaced.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10814355
    • W11305293

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error SUD OR SD

    How to Fix Amana Dishwasher Error SUD OR SD

    Error Code: SUD OR SD Difficulty: Easy

    Problem: Excessive suds have been detected in the dishwasher. This is often caused by using the wrong type or too much detergent.

    How to Fix SUD OR SD Error (Step-by-Step)

    1. Press the ‘Cancel/Drain’ button to stop the cycle and pump out the sudsy water.
    2. Open the dishwasher door carefully, as there may be a lot of suds.
    3. You can help break down the suds by pouring 1 cup of white vinegar or adding a few tablespoons of salt into the bottom of the dishwasher.
    4. Let the dishwasher sit for about an hour to allow the suds to dissipate.
    5. Once the suds are gone, close the door and run a ‘Rinse Only’ or a normal wash cycle with no dishes or detergent to flush out the machine.
    6. To prevent this, only use detergent specifically made for automatic dishwashers. Never use liquid dish soap for handwashing.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error DLO

    How to Fix Amana Dishwasher Error DLO

    Error Code: DLO Difficulty: Moderate

    Problem: Unbalanced load.

    How to Fix DLO Error (Step-by-Step)

    1. Open the dishwasher and check the loading of the racks. Rearrange dishes to create a more balanced load, ensuring nothing is blocking the spray arms.
    2. Verify that the dishwasher is level. Place a bubble level on the top edge of the open door and on the bottom rack. Adjust the leveling feet at the base of the dishwasher as needed.
    3. Close the door and try to start the cycle again.
    4. If the error persists, turn off power to the dishwasher at the circuit breaker.
    5. Remove the screws holding the inner door panel and separate it from the outer panel.
    6. Inspect the door latch and switches for any visible damage or loose connections.
    7. If the latch mechanism is broken, it will need to be replaced to resolve the error.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10130695
    • WPW10275768
    • WPW10653840

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error DRN

    How to Fix Amana Dishwasher Error DRN

    Error Code: DRN Difficulty: Hard

    Problem: Drain problem.

    How to Fix DRN Error (Step-by-Step)

    1. First, check the dishwasher filter located at the bottom of the tub. Remove it and clean any food particles or debris under running water.
    2. Inspect the drain hose for any visible kinks or bends that could be restricting water flow. Straighten the hose if necessary.
    3. Check where the drain hose connects to the sink’s plumbing or garbage disposal. Disconnect it and clear any clogs from the connection point.
    4. If you have a garbage disposal, run it to clear any food waste that might be blocking the drain.
    5. If the dishwasher still doesn’t drain, the drain pump may be clogged or has failed. Turn the appliance off to the dishwasher.
    6. You will need to access the drain pump by removing the bottom front panel of the dishwasher.
    7. Disconnect the hoses from the pump and check for obstructions. If the pump is clear but still doesn’t work, it will need to be replaced.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error OL

    How to Fix Amana Dishwasher Error OL

    Error Code: OL Difficulty: Easy

    Problem: Overloaded.

    How to Fix OL Error (Step-by-Step)

    1. Open the dishwasher door to view the contents and confirm the error stays cleared during a full test cycle.
    2. Remove several items from both the top and bottom racks to reduce the load.
    3. Rearrange the remaining dishes to ensure they are not nested together and that water can circulate freely.
    4. Make sure that tall items like baking sheets or large platters are not blocking the path of the spray arms.
    5. Spin the upper and lower spray arms by hand to ensure they can rotate a full 360 degrees without hitting any dishes.
    6. Close the dishwasher door securely and press the ‘Start/Resume’ button to restart the cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error UL

    How to Fix Amana Dishwasher Error UL

    Error Code: UL Difficulty: Easy

    Problem: Unbalanced load.

    How to Fix UL Error (Step-by-Step)

    1. Press the ‘Cancel’ or ‘Pause’ button to stop the dishwasher. Wait a moment for the cycle to halt completely before opening the door.
    2. Carefully slide out the bottom and top racks to inspect how the dishes are loaded.
    3. Identify any large, heavy items like pots, pans, or serving bowls that are grouped together on one side.
    4. Rearrange these heavy items, distributing them evenly around the bottom rack to balance the weight from side to side and front to back.
    5. Check that no dishes are blocking the spray arms. Gently spin the spray arms with your hand to ensure they can rotate freely without hitting anything.
    6. Securely slide both racks back into the dishwasher and close the door firmly until it latches.
    7. Press the ‘Start/Resume’ button to continue the cycle. The error should now be cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes