Category: Amana

  • How to Fix Amana Dishwasher Error F8E1

    How to Fix Amana Dishwasher Error F8E1

    Error Code: F8E1 Difficulty: Moderate

    Problem: Slow drain.

    How to Fix F8E1 Error (Step-by-Step)

    1. First, perform a basic cleaning. Remove the bottom dish rack and unscrew the filter assembly at the bottom of the tub. Clean it thoroughly under running water.
    2. Check the drain hose for any visible kinks or blockages. It’s the corrugated hose running from the dishwasher to your sink’s plumbing.
    3. Disconnect the drain hose from the garbage disposal or sink drain and place the end in a bucket. Start a ‘Drain’ cycle to see if water pumps out forcefully. If it does, the clog is in your sink plumbing.
    4. If water flow is weak, turn off power to the dishwasher at the circuit breaker. You will need to pull the dishwasher out from under the counter to access the drain pump.
    5. Disconnect the hoses from the drain pump (Part WPW10348269) and check its inlet and outlet ports for debris.
    6. If no clogs are found, the pump motor is likely weak and needs to be replaced.
    7. After clearing a clog or replacing the pump, reinstall the dishwasher, reconnect all hoses, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error F9E1

    How to Fix Amana Dishwasher Error F9E1

    Error Code: F9E1 Difficulty: Hard

    Problem: Drain pump failure.

    How to Fix F9E1 Error (Step-by-Step)

    1. Disconnect the dishwasher from power at the circuit breaker and shut off the hot water supply valve under the sink.
    2. Disconnect the water supply line and drain hose from the house plumbing. You may need to unscrew mounting brackets under the countertop before sliding the dishwasher out.
    3. Carefully lay the dishwasher on its back on a soft towel to access the components underneath.
    4. The drain pump (Part W10537869) is connected to the main sump. Place a shallow pan underneath to catch any remaining water.
    5. Squeeze the hose clamps with pliers to disconnect the hoses from the pump. Unplug the electrical connector. Twist the pump, usually counter-clockwise, to release it from the sump.
    6. Install the new pump by twisting it into the sump until it locks. Reconnect the electrical harness and the hoses, securing them with the clamps.
    7. Tip the dishwasher upright, slide it back into place, reconnect water and drain lines, restore power, and run a drain cycle to check for leaks and proper function.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error FD

    How to Fix Amana Dishwasher Error FD

    Error Code: FD Difficulty: Moderate

    Problem: Fill problem.

    How to Fix FD Error (Step-by-Step)

    1. Verify that the hot water supply valve under your sink is turned on completely.
    2. Pull the dishwasher out slightly and check the water supply hose for any sharp kinks or bends that could block water flow.
    3. Turn off the water supply valve. Disconnect the supply hose from the dishwasher’s inlet valve. Check the small screen inside the valve’s port for sediment and clean it with a small brush.
    4. Inside the dishwasher, locate the float assembly in the bottom of the tub. Lift the plastic float up and down to ensure it moves freely and isn’t stuck in the ‘up’ position, which would signal that the dishwasher is full.
    5. Ensure the drain hose has a ‘high loop’ (secured to the underside of the countertop) to prevent water from the sink from flowing back into the dishwasher, which can confuse the water level sensor.
    6. If these steps do not resolve the issue, the water inlet valve itself has likely failed and will need to be replaced.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: BLINKING

    How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: BLINKING

    Error Code: FRONT STATUS LIGHT: BLINKING Difficulty: Easy

    Problem: The cycle has been paused.

    How to Fix FRONT STATUS LIGHT: BLINKING Error (Step-by-Step)

    1. A blinking light typically indicates the wash cycle has been interrupted or paused, often by the door being opened.
    2. Ensure the door is completely closed. Push it firmly until you hear the latch click into place.
    3. Press the ‘Start/Resume’ button one time. The light should stop blinking and become solid, indicating the cycle has resumed.
    4. If you intended to stop the cycle, press and hold the ‘Cancel/Drain’ button for 3 seconds.
    5. If the light continues to blink after ensuring the door is latched and pressing ‘Start/Resume’, try resetting the dishwasher by turning it off at the circuit breaker for 5 minutes.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: BLUE

    How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: BLUE

    Error Code: FRONT STATUS LIGHT: BLUE Difficulty: Easy

    Problem: Washing in-progress.

    How to Fix FRONT STATUS LIGHT: BLUE Error (Step-by-Step)

    1. This is an informational light, not an error code and confirm the error stays cleared during a full test cycle.
    2. The blue light indicates that a wash cycle is currently in progress.
    3. No action is required from you and confirm the error stays cleared during a full test cycle.
    4. Allow the dishwasher to complete its cycle and confirm the error stays cleared during a full test cycle.
    5. The light will change or turn off once the cycle is finished.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: RED

    How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: RED

    Error Code: FRONT STATUS LIGHT: RED Difficulty: Easy

    Problem: Drying in-progress.

    How to Fix FRONT STATUS LIGHT: RED Error (Step-by-Step)

    1. This is an informational light, not an error code and confirm the error stays cleared during a full test cycle.
    2. The red light indicates that the drying cycle is currently in progress.
    3. No action is required from you and confirm the error stays cleared during a full test cycle.
    4. Wait for the dishwasher to finish the drying phase and confirm the error stays cleared during a full test cycle.
    5. The light will change to white or turn off when the entire cycle is complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: WHITE

    How to Fix Amana Dishwasher Error FRONT STATUS LIGHT: WHITE

    Error Code: FRONT STATUS LIGHT: WHITE Difficulty: Easy

    Problem: Cycle completed.

    How to Fix FRONT STATUS LIGHT: WHITE Error (Step-by-Step)

    1. This is an informational light, not an error code and confirm the error stays cleared during a full test cycle.
    2. The white light means the wash and dry cycles are complete.
    3. Your dishes are clean and ready to be unloaded and confirm the error stays cleared during a full test cycle.
    4. No further action is needed and confirm the error stays cleared during a full test cycle.
    5. The light will typically turn off after a set period or when the door is opened.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error H2O

    How to Fix Amana Dishwasher Error H2O

    Error Code: H2O Difficulty: Moderate

    Problem: Water supply issue. The dishwasher is not receiving enough water or any water at all.

    How to Fix H2O Error (Step-by-Step)

    1. First, ensure the water supply valve, usually located under your kitchen sink, is fully turned on.
    2. Carefully pull the dishwasher out and check the water supply hose for any kinks or twists that could block water flow. Straighten it if necessary.
    3. Turn off the water supply and disconnect the hose from the dishwasher’s inlet valve. Check the small screen filter inside the valve’s inlet for any sediment or debris and clean it with a small brush.
    4. If the screen is clean and the water supply is good, the water inlet valve itself may be faulty. Turn off power to the dishwasher at the circuit breaker.
    5. Remove the bottom front kick plate to access the valve. Disconnect the water line and the electrical wires from the old valve.
    6. Unscrew and remove the old valve. Install the new valve, ensuring all connections are secure.
    7. Reconnect the water line and electrical harness, turn the power and water back on, and run a test cycle while checking for leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10648041
    • W10844024
    • W11082871

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error HC

    How to Fix Amana Dishwasher Error HC

    Error Code: HC Difficulty: Easy

    Problem: Indicates that the hot and cold inlet hoses have been installed incorrectly.

    How to Fix HC Error (Step-by-Step)

    1. Turn off the power to the dishwasher at your home’s circuit breaker.
    2. Shut off both the hot and cold water supply valves, which are typically under the kitchen sink.
    3. Carefully slide the dishwasher out from under the counter to access the back where the hoses are connected.
    4. Identify the hot and cold water inlet connections on the dishwasher. They are usually marked.
    5. Verify that the hose from the hot water supply is connected to the hot water inlet, and the cold water hose is connected to the cold water inlet. If they are reversed, swap them.
    6. Ensure both hose connections are tight to prevent leaks and confirm the error stays cleared during a full test cycle.
    7. Slide the dishwasher back into place, turn the water and power back on, and start a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error LF

    How to Fix Amana Dishwasher Error LF

    Error Code: LF Difficulty: Moderate

    Problem: Long fill, the washer is taking too long to fill.

    How to Fix LF Error (Step-by-Step)

    1. Check that your home’s water supply valve for the dishwasher is completely open.
    2. Inspect the water inlet hose connected to the back of the dishwasher. Make sure it is not kinked or crushed, which would restrict water flow.
    3. Turn off the water supply. Disconnect the inlet hose and check the filter screen inside the connection port on the dishwasher. Clean any debris you find on the screen.
    4. The issue could also be a siphoning problem if the drain hose is installed incorrectly. Ensure the drain hose is looped up to the height of the countertop before it connects to the sink drain or garbage disposal.
    5. If the previous steps don’t resolve the issue, the water inlet valve may be failing and opening too slowly. This part controls the flow of water into the dishwasher.
    6. To replace the valve, turn off power and water, remove the front access panel, disconnect the lines and wires from the old valve, and install the new one.
    7. After installation, reconnect all lines, turn on power and water, and check for proper filling and any leaks.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10648041
    • W10844024
    • W11082871

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes