Category: Amana

  • How to Fix Amana Dishwasher Error F46

    How to Fix Amana Dishwasher Error F46

    Error Code: F46 Difficulty: Moderate

    Problem: Inlet Valve Sensor Error. There’s a problem with the inlet valve sensor.

    How to Fix F46 Error (Step-by-Step)

    1. Shut off both the power and the water supply to the dishwasher.
    2. The water inlet valve is typically located at the front, behind the lower kick panel. Remove the screws holding the kick panel in place.
    3. You will see the inlet valve with the water supply line and a hose connected to it. Place a towel underneath to catch any water.
    4. Disconnect the water supply line and the hose from the valve. You may need pliers for the hose clamp.
    5. Disconnect the wiring harness from the old valve and remove the screws that mount it to the dishwasher’s frame.
    6. Install the new water inlet valve, making sure to reconnect the wiring harness, water supply line, and hose securely.
    7. Turn the water supply back on and check for any leaks before reinstalling the kick panel and restoring power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error F47

    How to Fix Amana Dishwasher Error F47

    Error Code: F47 Difficulty: Hard

    Problem: Water Filtration System Issue. The dishwasher’s water filtration system is not operating correctly.

    How to Fix F47 Error (Step-by-Step)

    1. Disconnect the dishwasher from power and water. Turn off the circuit breaker for the dishwasher and shut off the water supply valve, usually located under the sink.
    2. Remove the lower dish rack to access the filter system at the bottom of the dishwasher tub.
    3. Twist the upper filter assembly counter-clockwise and lift it out. Then, pull out the lower filter that sits underneath it.
    4. Thoroughly clean both filters under running water. Use a soft brush to gently scrub away any food particles or debris. Do not use abrasive materials that could damage the filter mesh.
    5. While the filters are removed, inspect the filter housing and the sump area for any foreign objects or blockages. Carefully remove any debris you find.
    6. Inspect the drain hose for any kinks, clogs, or damage. Disconnect the hose from the dishwasher and the sink drain to check for obstructions. Clear any blockages you find.
    7. Reinstall the clean filters, ensuring they are securely locked in place. Reconnect the drain hose, restore power and water to the dishwasher, and run a short cycle to test the repair.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error F48

    How to Fix Amana Dishwasher Error F48

    Error Code: F48 Difficulty: Moderate

    Problem: Drain Hose Blockage. The dishwasher’s drain hose is blocked.

    How to Fix F48 Error (Step-by-Step)

    1. Disconnect the dishwasher from its power source and confirm the error stays cleared during a full test cycle.
    2. The drain hose connects the dishwasher’s drain pump to your sink’s drain or garbage disposal. You will need to access both ends.
    3. Place a bucket or towels under the sink connection to catch any water. Disconnect the drain hose from the sink drain or garbage disposal.
    4. Check this end of the hose for any blockages and clear them out.
    5. To check the entire hose, you may need to pull the dishwasher out slightly to access the connection at the drain pump. Disconnect the hose from the pump.
    6. With the hose completely detached, run water through it to flush out any remaining debris. If the hose is damaged or cracked, it should be replaced.
    7. Reconnect the drain hose to both the pump and the sink drain, ensuring a secure fit, then restore power.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • W11414944

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error F49

    How to Fix Amana Dishwasher Error F49

    Error Code: F49 Difficulty: Easy

    Problem: Water Quality Sensor Calibration Error. The calibration of the water quality sensor is incorrect.

    How to Fix F49 Error (Step-by-Step)

    1. This error often indicates a need to reset and recalibrate the dishwasher’s control board.
    2. Start by pressing the ‘Cancel’ button on the dishwasher to stop any ongoing cycle.
    3. Turn off the power to the dishwasher at the circuit breaker.
    4. Leave the power off for at least 5-10 minutes. This allows the internal electronics to fully reset.
    5. Turn the circuit breaker back on to restore power to the dishwasher.
    6. Select and run a short wash cycle. This will allow the water quality sensor to recalibrate during the new cycle.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and no-complete-cycle symptoms after the filter and hose are checked.

      Search Amazon for Whirlpool dishwasher drain pump

    • Whirlpool dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill, low-water, or no-water symptoms after supply and float checks.

      Search Amazon for Whirlpool dishwasher water inlet valve

    • Whirlpool dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating error-code or control faults after wiring and latch checks.

      Search Amazon for Whirlpool dishwasher control board

    Before ordering: match the part to the complete Amana dishwasher model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error F50

    How to Fix Amana Dishwasher Error F50

    Error Code: F50 Difficulty: Hard

    Problem: Spray Arm Motor Error. The dishwasher’s spray arm motor is malfunctioning.

    How to Fix F50 Error (Step-by-Step)

    1. Disconnect the dishwasher from the power supply by turning off the circuit breaker.
    2. You will need to pull the dishwasher out from under the counter to access the spray arm motor, which is part of the circulation pump assembly located underneath the tub.
    3. Lay the dishwasher on its back on a towel or blanket to protect the floor and the appliance.
    4. Disconnect the wiring harness and any hoses connected to the circulation pump motor.
    5. Remove the mounting screws or clamps that hold the pump and motor assembly in place.
    6. Carefully remove the old motor and install the new one, ensuring all seals are properly seated to prevent leaks.
    7. Reconnect the hoses and wiring, then carefully set the dishwasher upright, slide it back into place, and restore power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error F7E7

    How to Fix Amana Dishwasher Error F7E7

    Error Code: F7E7 Difficulty: Hard

    Problem: Indicates an issue with the appliance control unit, user interface, or associated wiring.

    How to Fix F7E7 Error (Step-by-Step)

    1. First, try a simple power reset. Turn off the circuit breaker for the dishwasher for at least 5 minutes.
    2. If the error persists, you will need to access the main control unit. Disconnect the power again.
    3. The control unit is typically located behind the lower kick panel or inside the door panel. You will need to remove the panel to access it.
    4. Carefully inspect all the wiring connections to and from the control unit and user interface. Look for any loose or damaged wires and reconnect or repair them as needed.
    5. If all wiring appears secure, the control unit itself is likely faulty and will need to be replaced. Disconnect all wire harnesses from the old board and remove it.
    6. Install the new control board, reconnect all wiring harnesses, and reassemble the dishwasher before restoring power.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Dishwasher Error FA

    How to Fix Amana Dishwasher Error FA

    Error Code: FA Difficulty: Hard

    Problem: The optical water indicator is detecting high levels of water turbidity.

    How to Fix FA Error (Step-by-Step)

    1. Turn off the power to the dishwasher at the circuit breaker.
    2. Remove the lower dish rack to access the sump area.
    3. Locate the optical water indicator (OWI) sensor, which is a small, clear plastic component.
    4. Disconnect the wire harness from the sensor and confirm the error stays cleared during a full test cycle.
    5. Rotate the sensor counter-clockwise to release it from the sump and pull it out.
    6. Install the new OWI sensor by aligning the tabs and turning it clockwise to lock it in place.
    7. Reconnect the wire harness and restore power to the dishwasher.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Dishwasher

    Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated.
    2. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication.
    3. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board.
    4. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Verified Compatible Alternatives:

    • WPW10705575

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error CLEAN COIL

    How to Fix Amana Refrigerator Error CLEAN COIL

    Error Code: CLEAN COIL Difficulty: Easy

    Problem: The condenser coil needs to be cleaned. This indicator light comes on after 3 months of elapsed time as a reminder.

    How to Fix CLEAN COIL Error (Step-by-Step)

    1. Unplug the refrigerator from the electrical outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the condenser coils, which are usually at the bottom of the refrigerator, behind the front kickplate grille or on the back.
    3. Remove the grille or access panel. The grille may pull straight off or be secured with screws.
    4. Use a coil cleaning brush and a vacuum cleaner with a hose attachment to gently clean the dust and debris from the coils.
    5. Be sure to clean the coils thoroughly, as well as the area around the condenser fan.
    6. Replace the grille or access panel and confirm the error stays cleared during a full test cycle.
    7. Plug the refrigerator back in and press any necessary reset button on the control panel to clear the reminder.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error CLEAN CONDENSER ALARM

    How to Fix Amana Refrigerator Error CLEAN CONDENSER ALARM

    Error Code: CLEAN CONDENSER ALARM Difficulty: Easy

    Problem: The condenser needs to be cleaned. The “Clean Condenser” indicator light comes on after three months of operation.

    How to Fix CLEAN CONDENSER ALARM Error (Step-by-Step)

    1. For your safety, disconnect the refrigerator from its power source.
    2. The condenser coils are typically located at the bottom of the unit. You may need to access them from the front by removing the base grille, or from the back by removing a service panel.
    3. Carefully remove the protective grille or panel and confirm the error stays cleared during a full test cycle.
    4. Using a condenser coil brush and a vacuum cleaner, gently remove all accumulated dust, pet hair, and debris from the coils.
    5. Clean the area around the coils and the condenser fan as well.
    6. Securely reattach the grille or panel and confirm the error stays cleared during a full test cycle.
    7. Plug the refrigerator back in. The alarm may reset automatically, or you may need to press and hold an ‘Alarm Reset’ button on the display for three seconds.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error HC

    How to Fix Amana Refrigerator Error HC

    Error Code: HC Difficulty: Easy

    Problem: Communication error between the electronic control boards.

    How to Fix HC Error (Step-by-Step)

    1. Safely pull the refrigerator away from the wall to access the power cord.
    2. Unplug the refrigerator from the electrical outlet and confirm the error stays cleared during a full test cycle.
    3. Leave the refrigerator unplugged for at least 10 minutes to allow the internal control boards to fully power down and reset.
    4. During this time, you can confirm the outlet is working by plugging in a small appliance like a lamp.
    5. Plug the refrigerator power cord back into the confirmed working outlet.
    6. Observe the control display for a few minutes to see if the communication error has cleared.
    7. If the ‘HC’ code returns, the problem requires a professional service to inspect the wiring and control boards.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Amana Refrigerator

    Focused repair path: refrigerator door, airflow, thermistor, defrost, fan, compressor start, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check.

    1. Confirm the doors seal, the interior lights shut off, and vents are not blocked before replacing sensors or boards.
    2. Look for frost pattern clues, stalled fans, warm compartments, water or ice symptoms, and recent power interruptions.
    3. For temperature faults, inspect the evaporator fan, thermistor, defrost path, damper, condenser airflow, and board connectors.
    4. Use the complete Amana refrigerator model number before ordering sensors, fans, boards, dampers, valves, or start components.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model.

    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Amana refrigerator part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Whirlpool refrigerator thermistor
      Common replacement category: Temperature sensor / thermistor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: temperature, cooling, or alarm symptoms after vent and setting checks.

      Search Amazon for Whirlpool refrigerator thermistor

    • Whirlpool refrigerator evaporator fan motor
      Common replacement category: Evaporator fan motor
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: airflow and uneven-cooling symptoms after frost and obstruction checks.

      Search Amazon for Whirlpool refrigerator evaporator fan motor

    • Whirlpool refrigerator control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Amana refrigerator model number. Confirm compatibility before buying.
      Why this category can matter: repeating electronic or cooling-control faults after power and wiring checks.

      Search Amazon for Whirlpool refrigerator control board

    Before ordering: match the part to the complete Amana refrigerator model number on the appliance tag.

    When It’s Better to Replace Than Repair

    Refrigerator repairs can become costly when sealed-system, control, defrost, fan, or ice-maker issues repeat.
    Confirm width, height, depth, door swing, counter-depth needs, water line, and delivery path before ordering.
    For repair parts, verify exact fit with the full refrigerator model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Water inlet valve, ice maker, or fan failures keep returning
    • [OK]Defrost heater, thermostat, or sensor faults stack up
    • [OK]Compressor or sealed-system repair is not economical
    • [OK]Food-loss risk is becoming a pattern

    Recommended Refrigerator Replacement Options

    Top-Freezer Models

    Simple Full-Size Replacements

    • Usually lower cost and easy to service
    • Confirm hinge side and kitchen clearance
    • Measure width, depth, and height

    Shop Top-Freezer Refrigerators

    Side-by-Side

    Ice and Water Convenience

    • Good for narrow door swing spaces
    • Confirm water line and filter access
    • Check freezer width for large items

    Compare Side-by-Side Models

    French-Door

    Premium Kitchen Layout

    • Popular wide fresh-food access
    • Confirm drawer clearance and counter depth
    • Measure delivery path before ordering

    View French-Door Refrigerators

    As an Amazon Associate, we earn from qualifying purchases.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Amana error codes: Amana Error Codes