Category: Amana

  • How to Fix Amana Dryer Error F3E2

    How to Fix Amana Dryer Error F3E2

    Error Code: F3E2 Difficulty: Moderate

    Problem: A moisture sensor issue has been detected. This can occur if five consecutive loads are dried without the sensor registering moisture.

    How to Fix F3E2 Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet to prevent electrical hazards.
    2. Locate the moisture sensor strips, which are two thin, metal bars typically found on the inside of the dryer drum, near the lint filter housing.
    3. Clean the sensor strips thoroughly with a soft cloth and rubbing alcohol, as a buildup of fabric softener residue can prevent them from working correctly.
    4. If cleaning doesn’t solve the issue, you may need to replace the sensor, which usually requires removing the front panel.
    5. Disconnect the wire harness leading to the sensor strips from the inside of the front panel.
    6. Remove the old sensor strips and install the new ones, ensuring they are securely in place. Reconnect the wiring.
    7. Reassemble the dryer, plug it in, and run a load to test the automatic cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Amana Dryer Error F22

    How to Fix Amana Dryer Error F22

    Error Code: F22 Difficulty: Moderate

    Problem: Indicates a door lock issue. The door may not be firmly shut, or there could be an obstruction.

    How to Fix F22 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure your safety during the repair.
    2. Open the dryer door and check for any clothes or foreign objects that might be preventing the door from closing securely.
    3. Inspect the door strike and the latch mechanism for any signs of damage or misalignment.
    4. To replace the door lock assembly, you will likely need to open the top panel or remove the front panel of the dryer.
    5. Locate the door lock assembly on the inside of the front panel and disconnect the wiring harness attached to it.
    6. Remove the screws securing the old lock assembly, take it out, and install the new one in its place.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Amana Dryer Error F30

    How to Fix Amana Dryer Error F30

    Error Code: F30 Difficulty: Easy

    Problem: Restricted airflow condition. This can be caused by a clogged lint screen, blocked door seal, or an obstructed vent.

    How to Fix F30 Error (Step-by-Step)

    1. Start by cleaning the lint screen. Remove it from its housing and thoroughly clean off all lint.
    2. Unplug the dryer from the power source before proceeding with further checks.
    3. Inspect the lint screen housing inside the dryer for any lint buildup that the screen might have missed and use a vacuum to clean it out.
    4. Check the dryer’s exhaust vent at the back. Ensure the ducting is not crushed, kinked, or clogged.
    5. Disconnect the vent from the dryer and clean out the entire length of the ducting to the outside of your home.
    6. Make sure the exterior vent flap on the outside of your house can open and close freely and is not blocked by debris.
    7. Once clear, reattach the vent, plug in the dryer, and start a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Amana Dryer Error E3

    How to Fix Amana Dryer Error E3

    Error Code: E3 Difficulty: Easy

    Problem: Signals that the dryer is overheating or has a temperature sensor issue, often due to a faulty thermistor or restricted airflow.

    How to Fix E3 Error (Step-by-Step)

    1. Unplug the dryer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Pull out the lint screen and thoroughly clean off all lint and debris.
    3. Inspect the lint screen housing for any accumulated lint that might be causing a blockage and use a vacuum with a narrow attachment to clean it out.
    4. Move the dryer away from the wall to access the exhaust vent.
    5. Disconnect the vent from the back of the dryer and check for any clogs or kinks in the ducting.
    6. Clean the entire length of the vent from the dryer to the outside of the house.
    7. Once everything is clear, reconnect the vent, plug the dryer back in, and try running a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Amana Dryer Error AF

    How to Fix Amana Dryer Error AF

    Error Code: AF Difficulty: Easy

    Problem: Restricted airflow is detected. This can be caused by a clogged lint screen, a kinked or crushed vent, or a blockage in the vent.

    How to Fix AF Error (Step-by-Step)

    1. Unplug the dryer from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate and remove the lint screen, which is usually found just inside the dryer door opening.
    3. Clean all lint and debris from the screen using your fingers. For stubborn residue, wash the screen with warm, soapy water and a soft brush, then rinse and dry it completely before reinserting.
    4. Use a vacuum cleaner with a long, narrow attachment to clean out the cavity where the lint screen is housed.
    5. Go behind the dryer and disconnect the flexible vent hose from both the dryer and the wall exhaust port.
    6. Inspect the entire length of the vent hose for any kinks, crushed sections, or blockages. Clear any obstructions you find.
    7. Check the exterior vent hood on the outside of your house to ensure the flap moves freely and is not blocked by lint, nests, or other debris.
    8. Once clear, reattach the vent hose securely at both ends, plug the dryer back in, and run a cycle to test.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You