Category: Amana

  • How to Fix Amana Washer Error RL

    How to Fix Amana Washer Error RL

    Error Code: RL Difficulty: Easy

    Problem: Items detected in the washer during the Clean Washer cycle.

    How to Fix RL Error (Step-by-Step)

    1. Press the ‘Pause’ or ‘Cancel’ button to stop the Clean Washer cycle.
    2. Wait for the lid to unlock, which may take a moment.
    3. Open the washer lid and look inside the drum and confirm the error stays cleared during a full test cycle.
    4. Remove any clothing, towels, or other items that were left inside.
    5. Close the lid securely and confirm the error stays cleared during a full test cycle.
    6. Select the ‘Clean Washer’ cycle again and confirm the error stays cleared during a full test cycle.
    7. Press the ‘Start’ button to run the cycle with a completely empty drum.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Washer Error UL

    How to Fix Amana Washer Error UL

    Error Code: UL Difficulty: Easy

    Problem: Unbalanced Load

    How to Fix UL Error (Step-by-Step)

    1. The washer has paused automatically. Press the ‘Pause’ or ‘Cancel’ button to ensure the cycle is stopped.
    2. Wait for the spinning to stop completely and for the lid to unlock.
    3. Open the lid and observe the clothes inside. They are likely gathered on one side of the drum.
    4. If washing one large or absorbent item, add a couple of towels to help balance the weight.
    5. Close the lid firmly and confirm the error stays cleared during a full test cycle.
    6. Press the ‘Start’ button to resume the cycle. The washer will attempt to spin again.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error 3 BEEPS

    How to Fix Amana Dryer Error 3 BEEPS

    Error Code: 3 BEEPS Difficulty: Moderate

    Problem: Can indicate a variety of issues, including a problem with the door switch or water getting into the control panel.

    How to Fix 3 BEEPS Error (Step-by-Step)

    1. Unplug the dryer from the power outlet to prevent electrical shock during the repair.
    2. Open the dryer door and locate the door switch. It’s a small button or lever that the door presses when it closes.
    3. To inspect the switch more closely, you may need to prop open the top of the dryer or remove the front panel, depending on your model.
    4. Disconnect the wires from the door switch terminals. Use a multimeter set to continuity to test the switch. The meter should show continuity when the button is pressed and no continuity when released.
    5. If the switch fails the test, replace it with a new one by securing it in place and reconnecting the wires.
    6. Reassemble the dryer, plug it back in, and check if the beeping issue is resolved.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W10169313
    • WPW10237959

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error PF

    How to Fix Amana Dryer Error PF

    Error Code: PF Difficulty: Hard

    Problem: A power failure has occurred, interrupting the drying cycle.

    How to Fix PF Error (Step-by-Step)

    1. First, confirm the dryer’s outlet is receiving power. Unplug the dryer and test the outlet by plugging in a small lamp or phone charger that you know is working.
    2. If the outlet is dead, go to your home’s main electrical panel and check for a tripped circuit breaker or a blown fuse for the dryer. Reset the breaker by flipping it completely off and then back on, or replace the fuse if necessary.
    3. If the outlet has power, the next step requires you to UNPLUG THE DRYER. Safety is critical.
    4. On the back of the dryer, remove the small metal plate that covers where the power cord connects to the machine. This is the terminal block.
    5. Visually inspect the wire connections on the terminal block. Look for any loose screws, broken wires, or signs of black scorching or melting. If a screw is loose, tighten it securely. If there is visible damage, the terminal block and power cord may need to be replaced.
    6. If the terminal block and power cord connections are secure and look clean, the power failure is likely due to an internal component failure, such as the main control board.
    7. Replacing internal electronic components requires specialized tools and knowledge. It is recommended to contact a certified appliance service to diagnose and replace the faulty part.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W11461215
    • W11607637
    • W11741989

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error F9E2

    How to Fix Amana Dryer Error F9E2

    Error Code: F9E2 Difficulty: Moderate

    Problem: Drain assembly failure. This indicates that the float switch is in the full position and the pump has been on for more than 60 seconds.

    How to Fix F9E2 Error (Step-by-Step)

    1. Disconnect the dryer from power before beginning any work and confirm the error stays cleared during a full test cycle.
    2. Locate the drain pump assembly, which is usually at the bottom front of the dryer. You may need to remove a lower access panel.
    3. Place towels and a shallow pan under the pump area to catch any water that may spill out.
    4. Carefully disconnect the hoses attached to the pump and inspect the hoses and the pump’s inlet and outlet ports for any lint or debris that could cause a blockage.
    5. Locate the float switch (W10903190) near the pump. Check to see if it moves freely up and down and is not stuck in the raised (full) position.
    6. If no blockages are found and the float switch moves correctly, the drain pump (W11551760) has likely failed and is not removing water.
    7. Replacing the drain pump assembly is recommended to resolve the issue.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W11551760

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error F70

    How to Fix Amana Dryer Error F70

    Error Code: F70 Difficulty: Hard

    Problem: Communication failure between the user interface board and the main control board.

    How to Fix F70 Error (Step-by-Step)

    1. Ensure the dryer is completely disconnected from the power supply by unplugging it.
    2. Access the dryer’s electronic boards by removing the necessary service panels (usually the top or back).
    3. Identify the user interface board (where you make your selections) and the main control board.
    4. Check the wiring that runs between these two boards for any loose plugs or visible damage.
    5. Unplug the connectors on both ends, inspect them for any bent or corroded pins, and then plug them back in firmly.
    6. If the connections are solid and the wires are intact, the communication failure is likely due to a faulty main control board (W10756689) or user interface board (W10280652).
    7. Because it is difficult to determine which board is at fault without proper check equipment, professional service is recommended.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W10756689

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error F7E1

    How to Fix Amana Dryer Error F7E1

    Error Code: F7E1 Difficulty: Hard

    Problem: Motor speed sensing error; the motor is not reaching the correct speed for the selected cycle.

    How to Fix F7E1 Error (Step-by-Step)

    1. Unplug the dryer from the electrical outlet to ensure your safety.
    2. Remove the front or rear panel of the dryer to get access to the drive motor and belt.
    3. Inspect the drive belt to make sure it is not broken, frayed, or stretched out. Ensure it is properly looped around the motor pulley and the drum.
    4. Check the idler pulley, which provides tension to the belt. Make sure its arm moves freely and that the pulley spins without resistance.
    5. If the belt and pulley system are in good condition, the error likely indicates a problem with the drive motor (W10410996) or its internal speed sensor.
    6. Replacing the drive motor is a complex task, and it is advisable to have a professional service complete the repair.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W10410996

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error F6E3

    How to Fix Amana Dryer Error F6E3

    Error Code: F6E3 Difficulty: Hard

    Problem: Indicates an issue with the appliance control unit, user interface, or associated wiring.

    How to Fix F6E3 Error (Step-by-Step)

    1. Turn off the circuit breaker for the dryer and unplug the appliance from the wall.
    2. Remove the top or rear panel to access the internal electronic components.
    3. Locate the main appliance control unit and the user interface board.
    4. Carefully examine the wire harness (part W10450289) that links the two boards for any signs of damage, like frayed wires or loose pins.
    5. Disconnect the harness from both boards, inspect the connection points for damage, and then reconnect it securely.
    6. If the wiring is secure and undamaged, the error points to a failure in either the main control unit (W10756689) or the user interface.
    7. Diagnosing which board has failed requires specialized tools, so it is best to contact a certified service for component testing and replacement.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W10756689

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error F23

    How to Fix Amana Dryer Error F23

    Error Code: F23 Difficulty: Moderate

    Problem: Fault in the exhaust/outlet thermistor.

    How to Fix F23 Error (Step-by-Step)

    1. Always begin by unplugging the dryer from the power outlet for safety.
    2. The outlet thermistor is usually located on the exhaust housing; you will need to remove the back panel of the dryer to access it.
    3. Locate the small, oval-shaped thermistor. It will have two wires connected to it.
    4. Disconnect the two wires from the thermistor terminals and confirm the error stays cleared during a full test cycle.
    5. Remove the screw that holds the thermistor in place and take out the old part.
    6. Install the new thermistor, secure it with the screw, and reconnect the two wires.
    7. Replace the back panel, plug the dryer back in, and run a test cycle to see if the error is resolved.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • DC32-00007A

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




  • How to Fix Amana Dryer Error F01

    How to Fix Amana Dryer Error F01

    Error Code: F01 Difficulty: Hard

    Problem: Primary control failure.

    How to Fix F01 Error (Step-by-Step)

    1. Disconnect the dryer from the power source by unplugging it from the wall outlet. This is a critical safety step.
    2. Locate the main control board, which is typically found inside the control console at the top of the dryer.
    3. Remove the screws holding the top or back panel of the control console to gain access to the board.
    4. Carefully take a photo of the wire connections on the old board to remember where everything goes.
    5. Disconnect all the wire harnesses from the old control board. They usually have locking tabs that need to be pressed.
    6. Remove the mounting screws holding the old board in place and install the new control board.
    7. Reconnect all the wire harnesses to the new board using your photo as a guide, reassemble the console, plug in the dryer, and test its functions.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Next Steps and Parts

    Verified Compatible Alternatives:

    • W11461215
    • W11741989

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.