Category: Amana

  • How to Fix Amana Refrigerator Error E44

    How to Fix Amana Refrigerator Error E44

    Error Code: E44 Difficulty: Moderate

    Problem: Refrigerator Fresh Food Fan Communication Error.

    How to Fix E44 Error (Step-by-Step)

    1. Disconnect the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
    2. Remove all shelves, drawers, and food from the fresh food compartment.
    3. Locate and remove the screws holding the panel at the back of the compartment. This panel covers the evaporator fan.
    4. Gently pull the panel away and disconnect any attached wiring to set it aside.
    5. Identify the fresh food evaporator fan motor. Unplug its wire harness.
    6. Remove the mounting screws holding the fan motor in place and take it out. You may need to transfer the fan blade to the new motor.
    7. Install the new motor, reconnect the wiring, and reassemble the compartment panels and shelves before plugging the unit back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E5

    How to Fix Amana Refrigerator Error E5

    Error Code: E5 Difficulty: Moderate

    Problem: Refrigerator Thermistor Error.

    How to Fix E5 Error (Step-by-Step)

    1. Unplug the refrigerator from the wall outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the thermistor. It’s usually inside the fresh food section, near the top, behind a small plastic cover.
    3. Remove any screws holding the cover in place and gently pry it off.
    4. Disconnect the wire harness attached to the old thermistor and confirm the error stays cleared during a full test cycle.
    5. Remove the old thermistor from its mounting clip and confirm the error stays cleared during a full test cycle.
    6. Snap the new thermistor into the clip, reconnect the wire harness, and secure the cover.
    7. Plug the refrigerator back in. The error should clear after a few minutes.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E51

    How to Fix Amana Refrigerator Error E51

    Error Code: E51 Difficulty: Hard

    Problem: Refrigerator Adaptive Defrost Communication Error.

    How to Fix E51 Error (Step-by-Step)

    1. Completely disconnect the refrigerator from its power source and confirm the error stays cleared during a full test cycle.
    2. Locate the main control board on the back of the unit, typically behind a metal or cardboard access panel.
    3. Remove the screws securing the panel and set it aside.
    4. Take a clear picture of the wire connections with your phone before disconnecting anything.
    5. Carefully unplug all wire harnesses from the old board. Most have a small locking tab you need to press to release them.
    6. Remove the old control board, which is usually held by a few mounting screws or plastic tabs.
    7. Install the new board, secure it, and use your photo to reconnect all wire harnesses to the correct terminals.
    8. Reinstall the access panel, plug the refrigerator in, and allow a few minutes for the system to initialize.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E6

    How to Fix Amana Refrigerator Error E6

    Error Code: E6 Difficulty: Easy

    Problem: Refrigerator Door Sensor Error.

    How to Fix E6 Error (Step-by-Step)

    1. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Locate the door switch along the interior frame of the refrigerator or freezer door.
    3. Use a plastic putty knife or a flathead screwdriver to gently pry the old switch out of its housing.
    4. Disconnect the two wires attached to the back of the old switch.
    5. Connect the wires to the terminals on the new switch.
    6. Firmly press the new switch into the opening in the frame until it snaps securely into place.
    7. Plug the refrigerator back in and test the interior light by opening and closing the door.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E7

    How to Fix Amana Refrigerator Error E7

    Error Code: E7 Difficulty: Hard

    Problem: Refrigerator Control Board Error.

    How to Fix E7 Error (Step-by-Step)

    1. Unplug the refrigerator from the wall to ensure no power is running to the unit.
    2. Access the rear of the refrigerator and locate the main control board, which is protected by an access panel.
    3. Unscrew and remove the access panel and confirm the error stays cleared during a full test cycle.
    4. Before touching any wires, take a detailed photograph of the board and all its connections for reference.
    5. Systematically disconnect each wire harness from the old board, pressing the release tabs as you go.
    6. Unclip or unscrew the old board from its mounting points and set it aside.
    7. Mount the new main control board, then carefully and correctly reconnect all wire harnesses based on your photo.
    8. Replace the rear access panel and its screws, then restore power to the refrigerator.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error E8

    How to Fix Amana Refrigerator Error E8

    Error Code: E8 Difficulty: Moderate

    Problem: Refrigerator Ice Maker Error.

    How to Fix E8 Error (Step-by-Step)

    1. Shut off the water supply to the refrigerator at the main valve and unplug the appliance from the wall.
    2. Open the freezer door and remove the ice bucket to gain access to the ice maker assembly.
    3. Locate the screws that mount the ice maker to the freezer wall (there are typically two or three).
    4. Support the ice maker with one hand while removing the screws with the other.
    5. Gently pull the ice maker forward and locate the main wire harness connecting it to the refrigerator.
    6. Depress the locking tab on the wire harness and pull to disconnect it.
    7. Connect the wire harness to the new ice maker assembly, mount it to the freezer wall with the screws, and replace the ice bucket.
    8. Restore power and water to the refrigerator and confirm the error stays cleared during a full test cycle.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error FLASHING ‘F’

    How to Fix Amana Refrigerator Error FLASHING ‘F’

    Error Code: FLASHING ‘F’ Difficulty: Easy

    Problem: Indicates a potential issue with the refrigerator’s cooling system or a sensor.

    How to Fix FLASHING ‘F’ Error (Step-by-Step)

    1. Open the refrigerator and freezer doors and check for any food items that may be blocking the air vents. Rearrange items to ensure clear airflow.
    2. Inspect the door gaskets to make sure they are clean and creating a complete seal when the doors are closed.
    3. Unplug the refrigerator from the power outlet and confirm the error stays cleared during a full test cycle.
    4. Leave the refrigerator unplugged for five full minutes to allow the internal computer to perform a hard reset.
    5. Plug the refrigerator back into the power outlet. The code should now be cleared.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error H2O LIGHT

    How to Fix Amana Refrigerator Error H2O LIGHT

    Error Code: H2O LIGHT Difficulty: Easy

    Problem: Indicates that the water filter needs to be replaced.

    How to Fix H2O LIGHT Error (Step-by-Step)

    1. Locate the water filter housing, which is typically in the upper-right corner of the fresh food compartment or in the base grille at the bottom.
    2. If in the grille, push the eject button to release the filter. If inside, turn the filter cap or the filter itself counter-clockwise about a quarter turn.
    3. Pull the old filter straight out from the housing. A small amount of water may drip out.
    4. Remove the protective caps from the new filter and insert it into the housing.
    5. Push the filter in and turn it clockwise until it locks firmly in place.
    6. Press and hold the ‘Filter Reset’ button on your dispenser control panel for about 3 seconds until the light turns off or changes color.
    7. Run approximately two gallons of water through the dispenser to flush the new filter before use.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error TEMPERATURE ALARM

    How to Fix Amana Refrigerator Error TEMPERATURE ALARM

    Error Code: TEMPERATURE ALARM Difficulty: Hard

    Problem: Indicates that the internal temperature of the refrigerator or freezer has exceeded a safe level.

    How to Fix TEMPERATURE ALARM Error (Step-by-Step)

    1. Unplug the refrigerator from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Locate the thermistor inside the fresh food or freezer compartment. It is usually behind a small plastic cover on the side or back wall.
    3. Gently pry off the cover with a small flathead screwdriver.
    4. Disconnect the wire harness attached to the thermistor and confirm the error stays cleared during a full test cycle.
    5. Remove the old thermistor. It may be held in place by a clip or screw.
    6. Install the new thermistor and reconnect the wire harness and confirm the error stays cleared during a full test cycle.
    7. Snap the cover back into place and plug the refrigerator back in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Thermistor (Temperature Sensor): W10316760
    • Thermistor (Temperature Sensor): WPW10383615

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Refrigerator Error DF

    How to Fix Amana Refrigerator Error DF

    Error Code: DF Difficulty: Easy

    Problem: Door Switch Problem or Door Not Closing Properly.

    How to Fix DF Error (Step-by-Step)

    1. Check for any items inside the refrigerator that may be blocking the door from closing completely.
    2. Inspect the door gaskets (the rubber seals around the door) for any food debris or spills and clean them with warm, soapy water.
    3. Ensure the refrigerator is level. Use a level to check and adjust the leveling feet at the bottom of the unit if necessary.
    4. Gently push the door shut to ensure the magnetic seal is engaging properly.
    5. If the door still does not close correctly, check the door hinges for any signs of damage or misalignment.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes