Author: Patch

  • How to Fix Kenmore Dishwasher Error PF

    How to Fix Kenmore Dishwasher Error PF

    Problem: Power failure detected during cycle

    How to Fix Dishwasher Error

    1. Check home power supply and circuit breakers.
    2. Verify GFCI outlets are not tripped.
    3. Inspect power cord for damage.
    4. Test voltage at dishwasher junction box.
    5. Reset dishwasher by pressing Start/Reset button.
    6. Allow dishwasher to complete cycle if power was restored.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Bosch Dishwasher Error WATER TAP SYMBOL

    How to Fix Bosch Dishwasher Error WATER TAP SYMBOL

    Error Code: WATER TAP SYMBOL Difficulty: Easy

    Problem: Problem with the water supply.

    How to Fix WATER TAP SYMBOL Error (Step-by-Step)

    1. Begin by checking the water supply valve connected to the dishwasher, typically located under your kitchen sink. Ensure the handle is turned fully counter-clockwise to the ‘on’ position.
    2. Pull the dishwasher out slightly from the cabinet to inspect the water inlet hose for any kinks or sharp bends that could restrict water flow.
    3. Gently straighten any part of the hose that is pinched or bent.
    4. Turn off the water supply valve. Place a small bucket or towel under the connection and unscrew the hose from the valve.
    5. Look inside the end of the hose for a small filter screen. Check if it is clogged with sediment or debris.
    6. Remove the screen with needle-nose pliers if possible and rinse it thoroughly under running water until clean. Re-insert the filter.
    7. Securely reattach the hose to the water supply valve, turn the water back on, and start a new cycle to clear the error.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Maytag Dishwasher Error F1E1

    How to Fix Maytag Dishwasher Error F1E1

    Problem: Electrical control system failure – main control board issue

    How to Fix Dishwasher Error

    1. Turn off power at the circuit breaker.
    2. Remove the control panel and access cover.
    3. Inspect the control board for burnt components or damaged traces.
    4. Check all wire harness connections for proper seating.
    5. Test the voltage supply to the control board.
    6. If the board shows signs of damage, document all wire connections.
    7. Disconnect all connectors from the control board.
    8. Remove mounting screws and extract the old control board.
    9. Install the new control board and reconnect all harnesses.
    10. Program the control board with model-specific settings if required.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)

    How to Fix Bosch Dishwasher Error RED LIGHT ON FLOOR (INFOLIGHT)

    Error Code: RED LIGHT ON FLOOR (INFOLIGHT) Difficulty: Easy

    Problem: The dishwasher is currently operating.

    How to Fix RED LIGHT ON FLOOR (INFOLIGHT) Error (Step-by-Step)

    1. Identify the red light shining on the floor beneath the dishwasher.
    2. Recognize that this ‘InfoLight’ is a standard feature indicating a wash cycle is in progress.
    3. Avoid opening the dishwasher door, as this will interrupt the cleaning and drying process.
    4. Allow the dishwasher to run undisturbed until the cycle is fully completed.
    5. The red light will automatically extinguish once the cycle has finished.
    6. You can now safely open the dishwasher and unload your clean dishes.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Bosch Dishwasher Error PRE-RINSE SYMBOL (SPRAY OF WATER)

    How to Fix Bosch Dishwasher Error PRE-RINSE SYMBOL (SPRAY OF WATER)

    Error Code: PRE-RINSE SYMBOL (SPRAY OF WATER) Difficulty: Easy

    Problem: The pre-rinse cycle is active.

    How to Fix PRE-RINSE SYMBOL (SPRAY OF WATER) Error (Step-by-Step)

    1. This symbol shows that the pre-rinse cycle is currently running.
    2. This is part of the normal operation to rinse dishes before the main wash cycle begins.
    3. No action is needed as this is not an error message.
    4. The dishwasher will automatically move to the main wash cycle after the pre-rinse is finished.
    5. You do not need any parts or to perform any repairs.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Kenmore Dishwasher Error Sanitize LED

    How to Fix Kenmore Dishwasher Error Sanitize LED

    Problem: Control panel could not detect sanitation temperature achievement

    How to Fix Dishwasher Error

    1. Check water temperature during sanitize cycle (must reach 150°F).
    2. Test temperature sensor accuracy and calibration.
    3. Verify heating element operation during sanitize cycle.
    4. Check control board sanitize cycle programming.
    5. Inspect water circulation during high-temperature phases.
    6. Replace temperature sensor or control board if needed.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes

  • How to Fix Bosch Dishwasher Error MACHINE CARE SYMBOL

    How to Fix Bosch Dishwasher Error MACHINE CARE SYMBOL

    Error Code: MACHINE CARE SYMBOL Difficulty: Easy

    Problem: It is time to run the “Machine Care” cleaning cycle.

    How to Fix MACHINE CARE SYMBOL Error (Step-by-Step)

    1. This light is a reminder to run the ‘Machine Care’ cleaning cycle.
    2. Make sure the dishwasher is empty of all dishes and confirm the error stays cleared during a full test cycle.
    3. Add a dishwasher cleaning tablet or liquid cleaner as recommended by the manufacturer.
    4. Close the door and select the ‘Machine Care’ cycle and confirm the error stays cleared during a full test cycle.
    5. Press the ‘Start’ button to begin the cleaning process and confirm the error stays cleared during a full test cycle.
    6. The light will turn off once the cycle is complete.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Maytag Dishwasher Error E9

    How to Fix Maytag Dishwasher Error E9

    Problem: Diverter system malfunction – water distribution issue

    How to Fix Dishwasher Error

    1. Disconnect power at the circuit breaker.
    2. Remove the lower access panel.
    3. Locate the diverter motor assembly under the tub.
    4. Inspect the diverter disc for debris or mechanical binding.
    5. Test the diverter motor resistance with a multimeter.
    6. Check the electrical connections for corrosion or damage.
    7. If the motor is faulty, disconnect the electrical connector.
    8. Remove mounting screws and replace the diverter motor.
    9. Ensure proper alignment of the diverter disc.
    10. Test the diverter operation during different wash cycles.

    As an Amazon Associate, we earn from qualifying purchases through links on this page.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Bosch Dishwasher Error BRUSH SYMBOL

    How to Fix Bosch Dishwasher Error BRUSH SYMBOL

    Error Code: BRUSH SYMBOL Difficulty: Easy

    Problem: The dishwasher is currently in the washing cycle.

    How to Fix BRUSH SYMBOL Error (Step-by-Step)

    1. This symbol means the dishwasher is in the middle of a wash cycle.
    2. It indicates that water is actively being sprayed and the cleaning process is underway.
    3. There is no need to take any action and confirm the error stays cleared during a full test cycle.
    4. Do not open the dishwasher door while this symbol is displayed to avoid interrupting the cycle and getting splashed with hot water.
    5. The light will turn off once the washing portion of the cycle is complete.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



  • How to Fix Kenmore Dishwasher Error Start Resume blinking

    How to Fix Kenmore Dishwasher Error Start Resume blinking

    Problem: Door opened during cycle or electrical interruption

    How to Fix Dishwasher Error

    1. Close dishwasher door firmly until it latches.
    2. Press Start/Resume button to continue cycle.
    3. Check door latch mechanism for proper operation.
    4. Verify door switches are making good contact.
    5. Ensure power supply is stable during operation.
    6. Reset control board if error persists after door closure.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Kenmore error codes: Kenmore Error Codes