Author: ApplianceFixGuide Team

  • How to Fix Amana Washer Error LDL

    How to Fix Amana Washer Error LDL

    Error Code: LDL Difficulty: Hard

    Problem: Lid Lock Failure

    How to Fix LDL Error (Step-by-Step)

    1. Disconnect the washing machine from its power source and confirm the error stays cleared during a full test cycle.
    2. Open the lid and locate the lid lock assembly, which is usually on the underside of the top panel.
    3. Inspect the lid strike (the plastic piece on the lid that goes into the lock) for any damage or misalignment. Adjust or replace if necessary.
    4. Examine the lid lock assembly for any visible signs of damage, such as cracks or broken pieces.
    5. Use a multimeter to test the continuity of the lid lock switch. If the switch is faulty, the entire assembly will need to be replaced.
    6. To replace the lid lock, remove the mounting screws, disconnect the wire harness, and install the new assembly.
    7. Reconnect the power and test the lid lock by starting a cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10810403
    • W11394572

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LD

    How to Fix Amana Washer Error LD

    Error Code: LD Difficulty: Hard

    Problem: Long Drain Time

    How to Fix LD Error (Step-by-Step)

    1. Unplug the washer from the wall outlet to ensure safety.
    2. Prepare some towels and a shallow pan to catch any residual water from the drain hose and pump.
    3. Access the drain pump, which is usually located at the bottom front of the washer. You may need to tilt the washer or remove a lower access panel.
    4. Disconnect the drain hose from the pump and check for any clogs or obstructions. Clear any blockage you find.
    5. Inspect the pump’s impeller to see if it’s broken or blocked. If it’s damaged, the entire pump assembly will need to be replaced.
    6. To replace the pump, disconnect the electrical wires and mounting screws. Install the new pump, ensuring all connections are tight.
    7. Reassemble the washer, plug it in, and run a drain/spin cycle to test the repair.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10730972

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LOC

    How to Fix Amana Washer Error LOC

    Error Code: LOC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LOC Error (Step-by-Step)

    1. Locate the ‘Control Lock’ button on the washer’s control panel.
    2. Press and hold the ‘Control Lock’ button for three to five seconds.
    3. The control lock light should turn off, indicating that the controls are now unlocked.
    4. If holding the button does not work, try unplugging the washer from the power outlet for one minute.
    5. Plug the washer back in and check if the control lock is deactivated.
    6. If the lock persists, there may be an issue with the control board, but this is rare for this specific error.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LO FL

    How to Fix Amana Washer Error LO FL

    Error Code: LO FL Difficulty: Hard

    Problem: Low Flow of Water

    How to Fix LO FL Error (Step-by-Step)

    1. Disconnect the washer from the power source and confirm the error stays cleared during a full test cycle.
    2. Shut off both the hot and cold water faucets and confirm the error stays cleared during a full test cycle.
    3. Check the water inlet hoses for any kinks or blockages and straighten them if necessary.
    4. Unscrew the hoses from the back of the washer and inspect the small filter screens inside the water inlet valve ports. Clean any debris from the screens.
    5. If the screens are clean and the hoses are clear, the water inlet valve may be faulty. Use a multimeter to test for continuity. If there is no continuity, it needs to be replaced.
    6. To replace the valve, disconnect the wire harnesses and internal hoses, then install the new valve.
    7. Reconnect all hoses and wires, turn the water and power back on, and test the washer.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LF

    How to Fix Amana Washer Error LF

    Error Code: LF Difficulty: Hard

    Problem: Long Fill

    How to Fix LF Error (Step-by-Step)

    1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Turn off the hot and cold water supplies to the washer.
    3. Using pliers, carefully disconnect the hot and cold water hoses from the back of the washer.
    4. Remove the screws securing the top panel of the washer and slide it off.
    5. Locate the water inlet valve at the back of the washer where the hoses were connected. Disconnect the wire harnesses and the tube from the valve.
    6. Replace the old water inlet valve with the new one, ensuring all connections are secure.
    7. Reassemble the washer, turn on the water and power, and run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LC

    How to Fix Amana Washer Error LC

    Error Code: LC Difficulty: Easy

    Problem: Control Lock Activated

    How to Fix LC Error (Step-by-Step)

    1. The ‘LC’ code indicates that the Control Lock or Child Lock feature has been activated, preventing any buttons from being pressed.
    2. Look for a button on your control panel that says ‘Control Lock’, ‘Lock’, or has a small padlock icon next to it.
    3. In many cases, this function is shared with another button, and you will see ‘Control Lock (Hold 3 Sec)’ printed below it.
    4. Press and hold that specific button for three to five consecutive seconds.
    5. The ‘LC’ light or code on the display should disappear.
    6. The controls are now unlocked, and you can operate the washer normally.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error INT

    How to Fix Amana Washer Error INT

    Error Code: INT Difficulty: Easy

    Problem: Cycle Paused or Canceled

    How to Fix INT Error (Step-by-Step)

    1. This code simply means the cycle was paused or canceled. This can happen if the ‘Start/Pause’ button is pressed mid-cycle or the power is interrupted.
    2. First, ensure the washer lid or door is fully closed and securely latched.
    3. Check that the washer is still plugged firmly into the wall outlet.
    4. Re-select the desired wash cycle using the main dial or buttons.
    5. Adjust any cycle settings like temperature or soil level as needed.
    6. Press and hold the ‘Start’ button for 3 seconds to begin the cycle again.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error HC

    How to Fix Amana Washer Error HC

    Error Code: HC Difficulty: Easy

    Problem: Hot and Cold Hoses are Reversed

    How to Fix HC Error (Step-by-Step)

    1. Press the ‘Cancel’ button to stop the washer and clear the code.
    2. Turn off the hot and cold water faucets located behind the machine.
    3. Unscrew both water inlet hoses from the back of the washer.
    4. Identify the ‘H’ (Hot) and ‘C’ (Cold) connection ports on the washer.
    5. Reconnect the hose coming from your home’s hot water supply to the ‘H’ port.
    6. Reconnect the hose coming from your home’s cold water supply to the ‘C’ port. Hand-tighten and then give a quarter-turn with pliers.
    7. Turn both water faucets back on completely, check for any leaks, and start a new cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error FILL OR SENSING LIGHT ON

    How to Fix Amana Washer Error FILL OR SENSING LIGHT ON

    Error Code: FILL OR SENSING LIGHT ON Difficulty: Hard

    Problem: Filling or Sensing

    How to Fix FILL OR SENSING LIGHT ON Error (Step-by-Step)

    1. First, ensure the water supply is on. Unplug the washer, turn off the water valves, and disconnect the inlet hoses from the back of the machine. Check the small filter screens inside the valve’s ports for any clogs and clean them.
    2. If the filters are clear, the water inlet valve itself may be faulty and need replacement. This requires removing the back panel for access.
    3. Another potential cause is a faulty lid switch. Open and close the lid to listen for a distinct ‘click’. If there is no click, or the machine won’t start, the lid switch assembly likely needs to be replaced.
    4. The fill sensor, also called the pressure switch, could be the problem. It’s typically located behind the control panel and is connected to a clear air tube.
    5. Access the control panel and inspect the air tube connected to the pressure switch. Ensure it is not kinked, cracked, or loose.
    6. If the tube is secure, the pressure switch itself may have failed and will need to be replaced by disconnecting its wire harness and the air tube.
    7. After inspecting or replacing any parts, reassemble the washer, turn on the water, and plug it in to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Fill Sensor/Pressure Switch

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error FD

    How to Fix Amana Washer Error FD

    Error Code: FD Difficulty: Easy

    Problem: Internal Board Problem – Drive Motor

    How to Fix FD Error (Step-by-Step)

    1. Unplug the washing machine from the electrical outlet and confirm the error stays cleared during a full test cycle.
    2. Leave the washer unplugged for at least five minutes. This allows the internal computer (control board) to fully discharge and reset itself.
    3. Plug the washer back into the power outlet and confirm the error stays cleared during a full test cycle.
    4. Select a new wash cycle of your choice and confirm the error stays cleared during a full test cycle.
    5. Press the ‘Start’ button to begin the new cycle and confirm the reset was successful.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes