Author: ApplianceFixGuide Team

  • How to Fix Amana Washer Error SD

    How to Fix Amana Washer Error SD

    Error Code: SD Difficulty: Easy

    Problem: Suds Detected

    How to Fix SD Error (Step-by-Step)

    1. Pause the current wash cycle and confirm the error stays cleared during a full test cycle.
    2. Allow the washer some time (about 30 minutes) to break down the excess suds on its own.
    3. Once the suds have dissipated, resume the wash cycle and confirm the error stays cleared during a full test cycle.
    4. For future washes, ensure you are using a high-efficiency (HE) detergent.
    5. Reduce the amount of detergent used, especially for smaller or lightly soiled loads.
    6. Run an empty ‘Clean Washer’ cycle with a washing machine cleaner to remove any detergent residue.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error RINSE LIGHT ON

    How to Fix Amana Washer Error RINSE LIGHT ON

    Error Code: RINSE LIGHT ON Difficulty: Moderate

    Problem: Rinsing

    How to Fix RINSE LIGHT ON Error (Step-by-Step)

    1. Unplug the washer and turn off the hot and cold water supply valves.
    2. Disconnect the water inlet hoses from the back of the machine.
    3. Remove the screws on the back panel to access the water inlet valve (Part W11220230).
    4. Take note of the electrical connections on the old valve before disconnecting them.
    5. Squeeze the clamps on the internal water hoses and slide them off the valve nozzles.
    6. Remove the screws holding the old valve in place and install the new one.
    7. Reconnect the hoses and electrical connections, then turn on the water and power to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F7E5

    How to Fix Amana Washer Error F7E5

    Error Code: F7E5 Difficulty: Hard

    Problem: Shifter fault.

    How to Fix F7E5 Error (Step-by-Step)

    1. Disconnect the washer from the electrical outlet to ensure your safety.
    2. Shut off the hot and cold water faucets that supply the washing machine.
    3. Lean the washer back against a wall to get access to the components underneath.
    4. Find the shifter/actuator, which is a small motor assembly mounted to the bottom of the wash tub.
    5. Unplug the electrical connector from the actuator and remove the mounting screws.
    6. Swap the old actuator with the new one, making sure to secure it with the screws and reconnect the wiring.
    7. Carefully set the washer upright, reconnect the power and water, and test its operation.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error PF

    How to Fix Amana Washer Error PF

    Error Code: PF Difficulty: Easy

    Problem: Power Failure

    How to Fix PF Error (Step-by-Step)

    1. Check if the washer’s power cord is firmly plugged into a working wall outlet.
    2. Verify that the circuit breaker for the laundry room has not tripped. If it has, reset it.
    3. Press the ‘Start/Pause’ button to see if the cycle will resume.
    4. If the washer does not start, try a different outlet to rule out a problem with the original outlet.
    5. Select a new wash cycle and press ‘Start’ and confirm the error stays cleared during a full test cycle.
    6. If the issue persists, unplug the washer for one minute to reset the internal electronics, then plug it back in and try again.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error OFB

    How to Fix Amana Washer Error OFB

    Error Code: OFB Difficulty: Hard

    Problem: The washer load is out of balance.

    How to Fix OFB Error (Step-by-Step)

    1. Unplug the washer and disconnect the water hoses and confirm the error stays cleared during a full test cycle.
    2. Open the washer lid and remove the washplate cap to access the central bolt.
    3. Unscrew the bolt and lift the washplate (Part W10780045) out of the tub.
    4. Underneath the washplate, locate and remove the drive hub kit (Part W10821956).
    5. Prop the washer up to access the bottom and replace the bearing kit (Part W11130362).
    6. At the same time, replace all four suspension rods (Part W10780048) located at each corner of the tub.
    7. Reassemble the washer by following these steps in reverse, then run a test cycle.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10780048
    • W10821956
    • W11130362

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error ND

    How to Fix Amana Washer Error ND

    Error Code: ND Difficulty: Moderate

    Problem: No drain. This is typically a drain pump problem or can be caused by excess suds.

    How to Fix ND Error (Step-by-Step)

    1. Unplug the washer from the power outlet for safety and confirm the error stays cleared during a full test cycle.
    2. Turn off the water supply and disconnect the drain hose from the wall drain.
    3. Place a bucket or pan under the drain pump to catch any residual water.
    4. Locate the drain pump at the bottom of the washer and disconnect the hoses attached to it.
    5. Remove the screws holding the drain pump (Part W10876600) in place and remove the old pump.
    6. Install the new drain pump and reconnect the hoses and mounting screws.
    7. Reconnect the main drain hose (Part WPW10730972) to the wall, plug in the washer, and run a drain/spin cycle to test.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • WPW10730972

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error MULTIPLE LIGHTS FLASHING

    How to Fix Amana Washer Error MULTIPLE LIGHTS FLASHING

    Error Code: MULTIPLE LIGHTS FLASHING Difficulty: Moderate

    Problem: General Error

    How to Fix MULTIPLE LIGHTS FLASHING Error (Step-by-Step)

    1. Unplug the washer from the power outlet to ensure safety.
    2. Turn off the hot and cold water supplies to the washer.
    3. Carefully slide the washer forward to access the back panel.
    4. Open the top panel of the washer to locate the suspension rods at each corner of the tub.
    5. One by one, replace each of the four suspension rods (Part W10780048) by first detaching the old rod from the tub and the washer base, then installing the new rod in the reverse order.
    6. Once all suspension rods are replaced, close the top panel and reconnect the water supplies.
    7. Plug the washer back in and run a test cycle to ensure the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error F7E0

    How to Fix Amana Washer Error F7E0

    Error Code: F7E0 Difficulty: Hard

    Problem: Power loss or issue with power supply components.

    How to Fix F7E0 Error (Step-by-Step)

    1. Unplug the washer from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel to get to the internal components.
    3. Check the wiring harness that connects the Appliance Control Unit and the User Interface for any visible damage, burns, or loose plugs.
    4. If the wiring is in good condition, the problem is likely with the Appliance Control Unit or the User Interface.
    5. Replacing the Appliance Control Unit is a common fix for this issue.
    6. Disconnect the wires going to the control unit, remove the screws holding it in place, and swap it with the new part.
    7. Reconnect everything, put the panel back on, and plug the washer in.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • Wiring Harness
    • Appliance Control Unit

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LID

    How to Fix Amana Washer Error LID

    Error Code: LID Difficulty: Hard

    Problem: Lid Open

    How to Fix LID Error (Step-by-Step)

    1. Ensure the washer is unplugged from the power outlet and confirm the error stays cleared during a full test cycle.
    2. Check that the lid is fully closed and that there are no items obstructing it from closing properly.
    3. Inspect the lid strike on the lid and the lid lock assembly on the washer’s top panel for any visible damage or misalignment.
    4. If the lid strike is broken, it will need to be replaced.
    5. If the lid lock assembly appears damaged or the switch is not being activated by the strike, the assembly will need to be replaced.
    6. To replace the lid lock, you will need to open the top panel, disconnect the wire harness from the old lock, and remove it. Then, install the new lock.
    7. After replacement, close the lid and plug in the washer to see if the error is cleared.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    Verified Compatible Alternatives:

    • W10810403
    • W11394572

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes

  • How to Fix Amana Washer Error LDU

    How to Fix Amana Washer Error LDU

    Error Code: LDU Difficulty: Hard

    Problem: Lid Unlock Failure

    How to Fix LDU Error (Step-by-Step)

    1. First, unplug the washer to prevent any electrical shock and confirm the error stays cleared during a full test cycle.
    2. Remove the top panel of the washer to get to the lid lock mechanism.
    3. Inspect the lock for any jammed clothing or debris that might be preventing it from unlocking.
    4. If there are no obstructions, the lid lock assembly is likely faulty and needs to be replaced. Disconnect the wiring and remove the old lock.
    5. Install the new lid lock assembly, reassemble the washer, and plug it back in to test.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.

    Verified Compatible Alternatives:

    • W10810403
    • W11394572

    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.




    Browse all Amana error codes: Amana Error Codes