Author: ApplianceFixGuide Team

How to Fix Whirlpool Washer Error LF
Problem: Long fill – water level not changing after inlet valves energized

How to Fix Washer Error
1. Verify both hot/cold water supply valves are fully open.
2. Disconnect fill hoses and check household water pressure (>20 PSI required).
3. Clean inlet valve screens by removing hoses and brushing debris from brass fittings.
4. Inspect fill hoses for kinks, excessive length (>6 feet), or internal collapse restricting flow.
5. Check drain hose installation – must not extend >
6. 5 inches into standpipe (causes siphoning during fill).
7. Verify drain hose height doesn’t exceed 96 inches above floor (restricts drainage causing False ‘full’ detection).
8. Remove top panel and locate pressure switch on right side wall.
9. Disconnect pressure hose and blow through it to clear moisture/debris blocking air passage.
10. If water flows adequately but error persists, replace water inlet valve assembly W
11. If inlet valve tests good, replace pressure switch W
12. After repair, verify washer fills to proper level within 6 minutes.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Dishwasher Error F08
Problem: Heater circuit failure or open heating element

How to Fix Dishwasher Error
1. Disconnect power and access heating element.
2. Test element for continuity (should read 8-20 ohms).
3. Check high-limit thermostat for proper operation.
4. Inspect wiring harness for damage or loose connections.
5. Test control board heater relay contacts.
6. Replace faulty component.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error F0E2
Problem: Excessive suds detected – suds lock condition (Cabrio platform equivalent of Sd)

How to Fix Washer Error
1. Press PAUSE/CANCEL once to stop cycle, wait 1 minute, then press again to clear display.
2. Select ‘Drain & Spin’ cycle without adding any detergent.
3. Allow washer to complete 2-3 consecutive drain/spin cycles to remove excess suds.
4. Use ONLY HE (High-Efficiency) detergent – never regular detergent in HE washer.
5. Measure detergent precisely: 2 tablespoons liquid HE or 1 tablespoon powder HE per normal load.
6. Avoid ‘ultra-concentrated’ detergents unless specifically labeled for HE machines.
7. Never exceed fabric softener fill line in dispenser – overdosing causes suds lock.
8. If suds persist, run empty ‘Clean Washer’ cycle with affresh tablet or 1 cup white vinegar.
9. Clean dispenser drawer thoroughly with warm water to remove caked detergent residue.
10. Verify drain pump filter is clean – debris can trap suds in recirculation system.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error HF
Problem: Hot water flow problem – insufficient hot water entering washer

How to Fix Washer Error
1. Verify hot water supply valve is fully open at washer connection.
2. Disconnect hot water hose and place in bucket – turn on supply to verify hot water flow.
3. If no hot water at hose, check household water heater operation and temperature setting (should be 120°F minimum).
4. Clean hot water inlet valve screen by removing hose and brushing debris from brass fitting.
5. Inspect hot water hose for kinks or excessive length restricting flow.
6. Remove top panel and locate water inlet valve assembly.
7. Disconnect hot water solenoid wiring harness and measure resistance (should be 500-1500 ohms).
8. Verify 120V AC reaches hot water solenoid during hot fill cycle (test at connector).
9. If solenoid resistance is infinite or receives no power, replace water inlet valve assembly W
10. After repair, run hot water cycle and verify temperature at dispenser outlet reaches 100°F+ within 2 minutes of fill start.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Dryer Error F70
Problem: User interface communication failure

How to Fix Dryer Error
1. Disconnect power at circuit breaker.
2. Remove control panel faceplate and access cover.
3. Inspect user interface board connectors for corrosion or damage.
4. Check ribbon cable connections between interface and main control.
5. Test communication signals with multimeter if possible.
6. Clean all electrical contacts with contact cleaner.
7. If connections are good but error persists, replace user interface board.
8. Document all wire connections before disconnecting.
9. Install new user interface board assembly.
10. Test all button functions and display operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error AF
Problem: Air flow fault – pressure switch detecting abnormal air pressure in system

How to Fix Washer Error
1. Unplug washer and remove top panel to access pressure switch.
2. Disconnect pressure hose from switch and inspect for cracks, kinks, or water accumulation.
3. Blow through pressure hose to clear moisture/debris – should have unrestricted airflow.
4. Verify hose connection at air dome on tub is secure and not clogged with detergent residue.
5. With hose disconnected from switch, multimeter should show NO continuity across terminals.
6. Gently blow into hose while monitoring continuity – switch should close at approximately
7. 5 PSI.
8. If switch doesn’t change state when blowing, replace pressure switch W
9. If switch tests good but error persists, inspect air dome port on tub for blockage (remove hose and probe with pipe cleaner).
10. Check for air leaks in pressure system: cracked tub, loose hose clamps, or damaged air dome.
11. If all components test good, replace main control board W10461397 as sensing circuit has failed.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error dl
Problem: Door lock failure – door not locking properly (older Duet models)

How to Fix Washer Error
1. Unplug washer and inspect door gasket for obstructions preventing full closure.
2. Remove lower kick panel to access door lock assembly.
3. Manually press door strike against lock mechanism – should hear distinct click when engaged.
4. Disconnect lock wiring harness and measure resistance: primary coil 300-600 ohms, secondary 1000-1500 ohms.
5. Verify 120V AC reaches lock during operation (test at connector with door closed).
6. Inspect lock strike plate alignment – should engage smoothly without binding.
7. Check wiring harness between lock and control board for damage near door hinge area.
8. If lock receives power but won’t engage, or resistance readings are infinite, replace door lock assembly WPW
9. After replacement, verify lock engages within 3 seconds of cycle start and releases within 2 minutes after cycle completion.
10. Test all cycles to confirm consistent door locking operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Kenmore Washer Error F13
Problem: Dispenser circuit error – detergent dispenser malfunction

How to Fix Washer Error
1. Turn off power supply.
2. Remove dispenser drawer and clean thoroughly.
3. Inspect dispenser housing for debris or mechanical binding.
4. Locate dispenser solenoid or wax motor assembly.
5. Test dispenser motor resistance with multimeter.
6. Check electrical connections for corrosion or damage.
7. If dispenser mechanism is faulty, remove mounting screws.
8. Replace entire dispenser assembly or individual solenoid.
9. Reinstall dispenser drawer and test operation.
10. Run diagnostic cycle to verify dispenser timing and function.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error FL
Problem: Flood condition detected – excessive water in base pan

How to Fix Washer Error
1. UNPLUG WASHER IMMEDIATELY and turn off water supply valves.
2. Tilt washer backward 45 degrees using wood blocks under front feet to access base pan.
3. Remove 3 screws securing base pan and lower carefully – expect significant standing water.
4. Dry base pan completely with towels and shop vacuum.
5. Locate source of flood: inspect inlet valve connections, drain pump seals, tub gasket, and hoses under pressure.
6. Common culprits: cracked outer tub, failed tub seal, split drain hose, or leaking inlet valve.
7. Run washer briefly with water supply on to observe leak source (use flashlight and mirror).
8. Replace leaking component: tub seal W10837740, drain hose WPW10351854, or inlet valve W
9. Verify float switch resets after pan is completely dry (should show open circuit).
10. Reinstall base pan and test washer through complete cycle monitoring for leaks every 5 minutes.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026
How to Fix Whirlpool Washer Error HC
Problem: Heater circuit failure – open circuit or short in heating system

How to Fix Washer Error
1. Unplug washer and remove lower front panel.
2. Locate heating element mounted on outer tub (typically 1800W).
3. Disconnect wiring harness from heater terminals.
4. Measure resistance across heater terminals with multimeter (should read 15-25 ohms).
5. If resistance is infinite (open circuit), replace heating element W
6. If resistance is zero (shorted), replace heating element immediately.
7. Check heater wiring harness for damage, rodent chewing, or melted insulation near heat source.
8. Verify continuity of heater relay on main control board (requires board removal and visual inspection).
9. Inspect tub for mineral buildup on heater sheath causing overheating and failure.
10. After repair, run hot water cycle and verify temperature increases steadily (should reach 120°F within 15 minutes of fill completion).
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
January 31, 2026