Error Code: ID0 Difficulty: Hard
Problem: Motor tacho fault.
How to Fix ID0 Error (Step-by-Step)
- Disconnect the dishwasher from power at the circuit breaker and shut off the hot water supply valve, usually located under the kitchen sink.
- Carefully pull the dishwasher out from under the counter. You may need to remove two mounting screws that secure the dishwasher to the countertop.
- Lay the dishwasher on its back on a towel or blanket to protect the floor and the appliance. This will give you access to the wash pump and motor assembly underneath.
- Place a shallow pan and towel under the existing pump to catch residual water. Loosen the hose clamps and disconnect the hoses from the pump. Then, unplug the electrical wire connectors attached to the motor.
- Locate and remove the mounting screws or brackets holding the wash pump and motor assembly in place. Remove the old assembly from the dishwasher.
- Install the new wash pump and motor assembly, securing it with the mounting hardware. Reconnect the hoses and tighten the clamps securely to prevent leaks. Plug the electrical connectors back into the new motor.
- Carefully tilt the dishwasher upright, slide it partially back in, and reconnect the power and water supply. Run a short rinse cycle to check thoroughly for any leaks before fully reinstalling the unit under the counter.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher
Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
- Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
- Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
- Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
- Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
- Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.
Recommended Parts to Check
No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
-
Electrolux dishwasher drain pump
Common replacement category: Drain pump
Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.
Search Amazon for Electrolux dishwasher drain pump
-
Electrolux dishwasher water inlet valve
Common replacement category: Water inlet valve
Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
Why this category can matter: fill or low-water symptoms after supply and float checks.
Search Amazon for Electrolux dishwasher water inlet valve
-
Electrolux dishwasher control board
Common replacement category: Electronic control board
Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
Why this category can matter: repeating control faults after latch, wiring, and power checks.
Search Amazon for Electrolux dishwasher control board
Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair
Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
Built-In Dishwashers
Standard 24-Inch Models
- Common under-counter replacement size
- Check height, width, and toe-kick clearance
- Match hardwire or cord connection requirements
Shop Built-In Dishwashers
Compact Options
18-Inch and Small-Space Models
- Useful for narrow cabinets
- Confirm ADA or compact dimensions
- Verify panel and handle clearance
Compare Compact Dishwashers
Portable and Countertop
No Built-In Cabinet Cutout
- Good for rentals or limited cabinets
- Confirm faucet adapter compatibility
- Measure counter or storage space
View Portable Dishwashers
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Electrolux error codes: Electrolux Error Codes
