Author: ApplianceFixGuide Team

  • How to Fix Electrolux Dishwasher Error I70

    How to Fix Electrolux Dishwasher Error I70

    Error Code: I70 Difficulty: Moderate

    Problem: There is an open or short-circuit of the NTC thermistor (temperature sensor). The program will continue to the end without heating.

    How to Fix I70 Error (Step-by-Step)

    1. Turn off the power to the dishwasher at the circuit breaker.
    2. The thermistor is typically located on the underside of the dishwasher tub. You may need to pull the dishwasher out to access it.
    3. Locate the thermistor and disconnect the wire harness connected to it.
    4. Use a multimeter to test the resistance of the thermistor. The resistance should change with temperature. An open or shorted thermistor needs replacement.
    5. To replace, unscrew or unclip the old thermistor and install the new one.
    6. Reconnect the wire harness and slide the dishwasher back into place.
    7. Restore power and run a wash cycle to ensure the dishwasher is heating correctly.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Electrolux Dishwasher

    Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.

    1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
    2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
    3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
    4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
    5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.

    Verified Compatible Alternatives:

    • 808137001

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error I60, E60

    How to Fix Electrolux Dishwasher Error I60, E60

    Error Code: I60, E60 Difficulty: Hard

    Problem: Water heating problem. The dishwasher is not heating the water correctly.

    How to Fix I60, E60 Error (Step-by-Step)

    1. Disconnect the dishwasher from power and confirm the error stays cleared during a full test cycle.
    2. To access the heating element and thermostat, you will need to pull the dishwasher out from its installation.
    3. The heating element is located at the bottom of the tub. Inspect it for any visible signs of damage or burnout.
    4. Use a multimeter to test the continuity of the heating element. A lack of continuity indicates a faulty element.
    5. Disconnect the wires from the old heating element and remove it. Install the new element and reconnect the wires.
    6. Locate the high-limit thermostat, usually near the heating element, and test it for continuity as well. Replace if faulty.
    7. Reinstall the dishwasher and run a cycle that requires heating to verify the repair.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Verified Compatible Alternatives:

    • 154825001
    • 50277796004

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error I40, E40

    How to Fix Electrolux Dishwasher Error I40, E40

    Error Code: I40, E40 Difficulty: Easy

    Problem: Clogged filter or sump. Food soil has built up in the filter system.

    How to Fix I40, E40 Error (Step-by-Step)

    1. Turn off the dishwasher and confirm the error stays cleared during a full test cycle.
    2. Remove the lower dish rack to access the filter system at the bottom of the tub.
    3. Twist the cylindrical filter counter-clockwise and lift it out and confirm the error stays cleared during a full test cycle.
    4. Separate the fine filter from the coarse filter and confirm the error stays cleared during a full test cycle.
    5. Wash both filters under warm running water, using a soft brush to remove any food particles.
    6. Clean the sump area where the filter sits and confirm the error stays cleared during a full test cycle.
    7. Reassemble the filter system and place it back in the dishwasher, twisting clockwise to lock it in place.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Electrolux Dishwasher

    Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.

    1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
    2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
    3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
    4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
    5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error I30, E30, 3 FLASHES

    How to Fix Electrolux Dishwasher Error I30, E30, 3 FLASHES

    Error Code: I30, E30, 3 FLASHES Difficulty: Hard

    Problem: Anti-flood system activated. A leak has been detected in the base of the dishwasher.

    How to Fix I30, E30, 3 FLASHES Error (Step-by-Step)

    1. Disconnect the dishwasher from power and water and confirm the error stays cleared during a full test cycle.
    2. Pull the dishwasher out from under the counter to access the base pan.
    3. Locate the anti-flood switch, which is a float switch in the base of the dishwasher.
    4. Inspect the base for water and use a sponge or towel to dry it completely.
    5. Check for the source of the leak, which could be a loose hose, a cracked tub, or a faulty seal.
    6. Replace the float switch if it is damaged or stuck.
    7. After addressing the leak and ensuring the base is dry, reassemble and test the dishwasher.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Electrolux Dishwasher

    Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.

    1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
    2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
    3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
    4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
    5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error B2

    How to Fix Electrolux Dishwasher Error B2

    Error Code: B2 Difficulty: Hard

    Problem: Tank overflow.

    How to Fix B2 Error (Step-by-Step)

    1. Shut off the power and water supply to the dishwasher.
    2. Remove the bottom dish rack to access the filter and sump area.
    3. Unscrew the filter and remove any debris that may be causing a blockage.
    4. Inspect the drain hose for any kinks or clogs and straighten or clear it as needed.
    5. If the issue persists, the drain pump may be faulty and need to be replaced by following the steps for an inefficient drain.
    6. Once clear, reassemble the filter and run a test cycle to ensure proper drainage.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Verified Compatible Alternatives:

    • A00044305
    • A00055408

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error B1

    How to Fix Electrolux Dishwasher Error B1

    Error Code: B1 Difficulty: Hard

    Problem: Inefficient drain.

    How to Fix B1 Error (Step-by-Step)

    1. Disconnect the dishwasher from power and water supplies and confirm the error stays cleared during a full test cycle.
    2. Remove the lower access panel and toe kick to access the drain pump.
    3. Place a towel under the drain pump to catch any residual water.
    4. Disconnect the drain hose and the wire harness from the pump.
    5. Remove the mounting screws holding the drain pump in place and remove the old pump.
    6. Install the new drain pump, reconnecting the hose and wire harness.
    7. Reinstall the access panels, reconnect power and water, and run a drain cycle to test the new pump.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Electrolux Dishwasher

    Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.

    1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
    2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
    3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
    4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
    5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.

    Verified Compatible Alternatives:

    • A00044305
    • A00055408

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error ER-09

    How to Fix Electrolux Dishwasher Error ER-09

    Error Code: ER-09 Difficulty: Moderate

    Problem: There is a communication failure between the user interface control and the electronic control board.

    How to Fix ER-09 Error (Step-by-Step)

    1. Reset the dishwasher’s power. Turn off the circuit breaker dedicated to the dishwasher for at least five minutes to allow the internal electronics to fully discharge and reset.
    2. If the code persists, turn the power off again at the circuit breaker. You will now inspect the wire connection to the user interface in the door.
    3. Open the dishwasher door and remove the Torx screws holding the inner door panel to the outer panel. Be sure to support the outer panel as you remove the last screws so it doesn’t fall.
    4. Locate the main wire harness that connects to the user interface control at the top of the door. Carefully disconnect the plastic connector by squeezing its locking tab and pulling gently.
    5. Inspect the connector and the pins on the board for any signs of corrosion or damage. If it looks clean, firmly plug the connector back in until you hear it click into place, ensuring a secure connection.
    6. Reassemble the door panels, restore power at the circuit breaker, and run a test cycle to confirm the error is resolved. If the error returns, the main control board or user interface may need professional service.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error ER-08

    How to Fix Electrolux Dishwasher Error ER-08

    Error Code: ER-08 Difficulty: Hard

    Problem: A user interface control failure has occurred.

    How to Fix ER-08 Error (Step-by-Step)

    1. Disconnect the dishwasher from power by turning off the circuit breaker.
    2. Open the dishwasher door and remove the Torx screws holding the inner door panel to the outer panel.
    3. Separate the inner and outer door panels to access the user interface control board.
    4. Carefully disconnect the wire harnesses connected to the control board.
    5. Remove the old control board and install the new one, ensuring all wire harnesses are securely reconnected.
    6. Reassemble the door panels and restore power to the dishwasher to see if the error is cleared.
    7. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Electrolux Dishwasher

    Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.

    1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
    2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
    3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
    4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
    5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.

    Verified Compatible Alternatives:

    • 5304517208

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error ER-07 OR ER-11

    How to Fix Electrolux Dishwasher Error ER-07 OR ER-11

    Error Code: ER-07 OR ER-11 Difficulty: Hard

    Problem: There is a failure with the drain valve.

    How to Fix ER-07 OR ER-11 Error (Step-by-Step)

    1. Shut off electrical power and the main water supply to the dishwasher.
    2. Pull the dishwasher out from under the counter and carefully lay it on its back on a soft surface like a blanket.
    3. Locate the drain valve, which is connected to the drain pump and drain hose at the bottom of the dishwasher.
    4. Place a shallow pan or towel underneath to catch any remaining water.
    5. Disconnect the wire harness from the drain valve and confirm the error stays cleared during a full test cycle.
    6. Loosen the clamps securing the hoses to the valve and pull the hoses off.
    7. Remove the old valve, install the new one, and securely reattach the hoses and wire harness before setting the dishwasher upright.
    8. Turn the appliance off, wait about 2 minutes, then turn it back on.

    What to Check Next on This Electrolux Dishwasher

    Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.

    1. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
    2. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
    3. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
    4. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
    5. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.

    Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.

  • How to Fix Electrolux Dishwasher Error ER-06

    How to Fix Electrolux Dishwasher Error ER-06

    Error Code: ER-06 Difficulty: Moderate

    Problem: A lower fan failure has occurred.

    How to Fix ER-06 Error (Step-by-Step)

    1. Begin by performing a hard reset on the dishwasher. Turn off the circuit breaker that powers the dishwasher for at least 5 minutes. This can sometimes clear temporary electronic faults.
    2. After restoring power, open the dishwasher door and completely remove the lower dish rack to get clear access to the bottom of the tub.
    3. Locate the lower fan assembly. This is typically a round vent or grille at the back or side of the dishwasher’s interior tub, part of the drying system.
    4. Carefully inspect the fan vent for any visible obstructions. Look for small utensils, plastic lids, food debris, or other items that may have fallen and could be blocking the fan blades from spinning.
    5. If you find an obstruction, carefully remove it. You may need pliers or tweezers for smaller items. Ensure the area is completely clear.
    6. Turn the appliance off, wait about 2 minutes, then turn it back on.
    7. Check for simple blockages (lint screen, drain path, or filter) and clean anything you find.
    Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect.

    Recommended Parts to Check

    No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.

    • Electrolux dishwasher drain pump
      Common replacement category: Drain pump
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.

      Search Amazon for Electrolux dishwasher drain pump

    • Electrolux dishwasher water inlet valve
      Common replacement category: Water inlet valve
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: fill or low-water symptoms after supply and float checks.

      Search Amazon for Electrolux dishwasher water inlet valve

    • Electrolux dishwasher control board
      Common replacement category: Electronic control board
      Fit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.
      Why this category can matter: repeating control faults after latch, wiring, and power checks.

      Search Amazon for Electrolux dishwasher control board

    Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.

    Repair-Or-Replace Cost Calculator

    Use this calculator when the Electrolux dishwasher still fails after the basic checks. Compare the estimated repair cost, appliance age, and replacement price before ordering parts.


    Still Not Working?
    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Browse all Electrolux error codes: Electrolux Error Codes

    When It’s Better to Replace Than Repair

    Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
    Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
    For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.

    • [OK]Drain pump or circulation pump failure
    • [OK]Leaking tub, door, or float-switch issues
    • [OK]Heater or control failures on an older unit
    • [OK]Repeated poor washing or drying performance

    Recommended Dishwasher Replacement Options

    Built-In Dishwashers

    Standard 24-Inch Models

    • Common under-counter replacement size
    • Check height, width, and toe-kick clearance
    • Match hardwire or cord connection requirements

    Shop Built-In Dishwashers

    Compact Options

    18-Inch and Small-Space Models

    • Useful for narrow cabinets
    • Confirm ADA or compact dimensions
    • Verify panel and handle clearance

    Compare Compact Dishwashers

    Portable and Countertop

    No Built-In Cabinet Cutout

    • Good for rentals or limited cabinets
    • Confirm faucet adapter compatibility
    • Measure counter or storage space

    View Portable Dishwashers

    As an Amazon Associate, we earn from qualifying purchases.