Skip to main content
Appliance Fix Guide

Samsung Washer error code

Samsung Washer Error 9E1

Measure wall outlet voltage under load with multimeter (minimum 105V AC required during operation).

Measure wall outlet voltage under load with multimeter (minimum 105V AC required during operation).

UnknownStart with 5-15 minutes of safe checks
⚠️ CHECK WARRANTY / AGE$100 - $250 Range
Samsung washer repair guide for error 9E1
Error code9E1Washer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Measure wall outlet voltage under load with multimeter

    Measure wall outlet voltage under load with multimeter (minimum 105V AC required during operation).

  2. 2
    Check for shared circuit with high-draw appliances (AC

    Check for shared circuit with high-draw appliances (AC units, microwaves) causing voltage sag.

  3. 3
    Inspect power cord connections at terminal block inside

    Inspect power cord connections at terminal block inside machine - tighten screws to 8 in-lbs if loose.

A quick explanation

What does 9E1 mean?

Measure wall outlet voltage under load with multimeter (minimum 105V AC required during operation).

The answer you came for

How to fix Samsung washer error 9E1

Start with the safest checks and work from simple to technical.

  1. 1

    Measure wall outlet voltage under load with multimeter

    Measure wall outlet voltage under load with multimeter (minimum 105V AC required during operation).

  2. 2

    Check for shared circuit with high-draw appliances (AC

    Check for shared circuit with high-draw appliances (AC units, microwaves) causing voltage sag.

  3. 3

    Inspect power cord connections at terminal block inside

    Inspect power cord connections at terminal block inside machine - tighten screws to 8 in-lbs if loose.

  4. 4

    Test noise filter DC96-00488A for continuity between input/output

    Test noise filter DC96-00488A for continuity between input/output terminals (should read

  5. 5

    Replace noise filter assembly if open circuit or

    Replace noise filter assembly if open circuit or burnt appearance on components.

  6. 6

    If filter good but error returns within 10

    If filter good but error returns within 10 seconds of power-up: replace main PCB DC92-01543A (faulty voltage monitoring circuit).

  7. 7

    Install dedicated 120V/15A circuit if household voltage unstable

    Install dedicated 120V/15A circuit if household voltage unstable below 105V during operation.

  8. 8

    Restart the washer and confirm the 9E1 message

    Restart the washer and confirm the 9E1 message returns under the same condition instead of after a one-time interruption.

  9. 9

    Check the simple causes first

    Check the simple causes first: load balance, water supply, drain flow, door or lid closure, visible leaks, and power stability.

  10. 10

    Inspect accessible wiring connectors and moisture-prone areas before

    Inspect accessible wiring connectors and moisture-prone areas before assuming the control board has failed.

  11. 11

    Use the complete Samsung washer model number from

    Use the complete Samsung washer model number from the door, lid, or rear tag before matching any pump, valve, sensor, suspension, lock, or board category.

  12. 12

    If the 9E1 code points to a specific

    If the 9E1 code points to a specific system, test that system directly before ordering replacement parts.

Read the additional checks from the current guide

How to Fix 9E1 Error Measure wall outlet voltage under load with multimeter (minimum 105V AC required during operation).Check for shared circuit with high-draw appliances (AC units, microwaves) causing voltage sag.Inspect power cord connections at terminal block inside machine - tighten screws to 8 in-lbs if loose.Test noise filter DC96-00488A for continuity between input/output terminals (should read

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

Recommended part

Recommended part for this error code

No replacement part recommended for this code

The researched guidance for Samsung Washer error 9E1 points to user-action and diagnostic steps above rather than a mapped replacement part. We will not invent a part or send you to an unrelated product.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Samsung Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.