Skip to main content
Appliance Fix Guide

Samsung Washer error code

Samsung Washer Error 8E

Unplug washer and inspect main power cord for damage or fraying near strain relief.

Unplug washer and inspect main power cord for damage or fraying near strain relief.

HardStart with 5-15 minutes of safe checks
⚠️ CHECK WARRANTY / AGE$100 - $250 Range
Samsung washer repair guide for error 8E
Error code8EWasher

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Unplug washer and inspect main power cord for

    Unplug washer and inspect main power cord for damage or fraying near strain relief.

  2. 2
    Check household circuit breaker for partial trip condition

    Check household circuit breaker for partial trip condition (reset fully OFF then ON).

  3. 3
    Test noise filter DC96-00488A resistance between L-N (should

    Test noise filter DC96-00488A resistance between L-N (should read 1-2MΩ) and L-G/N-G (should read OL).

A quick explanation

What does 8E mean?

Unplug washer and inspect main power cord for damage or fraying near strain relief.

The answer you came for

How to fix Samsung washer error 8E

Start with the safest checks and work from simple to technical.

  1. 1

    Unplug washer and inspect main power cord for

    Unplug washer and inspect main power cord for damage or fraying near strain relief.

  2. 2

    Check household circuit breaker for partial trip condition

    Check household circuit breaker for partial trip condition (reset fully OFF then ON).

  3. 3

    Test noise filter DC96-00488A resistance between L-N (should

    Test noise filter DC96-00488A resistance between L-N (should read 1-2MΩ) and L-G/N-G (should read OL).

  4. 4

    Measure inrush current during startup with clamp meter

    Measure inrush current during startup with clamp meter (should not exceed 15A for first 2 seconds).

  5. 5

    If current normal but error persists immediately on

    If current normal but error persists immediately on power-up: replace main PCB DC92-01543A.

  6. 6

    If current excessive

    If current excessive: inspect all loads (heater, pump, motor) for shorts to ground using megohmmeter (>1MΩ required).

  7. 7

    Verify proper grounding continuity from chassis ground lug

    Verify proper grounding continuity from chassis ground lug to outlet ground terminal (

  8. 8

    Restart the washer and confirm the 8E message

    Restart the washer and confirm the 8E message returns under the same condition instead of after a one-time interruption.

  9. 9

    Check the simple causes first

    Check the simple causes first: load balance, water supply, drain flow, door or lid closure, visible leaks, and power stability.

  10. 10

    Inspect accessible wiring connectors and moisture-prone areas before

    Inspect accessible wiring connectors and moisture-prone areas before assuming the control board has failed.

  11. 11

    Use the complete Samsung washer model number from

    Use the complete Samsung washer model number from the door, lid, or rear tag before matching any pump, valve, sensor, suspension, lock, or board category.

  12. 12

    If the 8E code points to a specific

    If the 8E code points to a specific system, test that system directly before ordering replacement parts.

Read the additional checks from the current guide

How to Fix 8E Error Unplug washer and inspect main power cord for damage or fraying near strain relief.Check household circuit breaker for partial trip condition (reset fully OFF then ON).Test noise filter DC96-00488A resistance between L-N (should read 1-2MΩ) and L-G/N-G (should read OL).Measure inrush current during startup with clamp meter (should not exceed 15A for first 2 seconds).If current normal but error persists immediately on power-up: replace main PCB DC92-01543A.If current excessive: inspect all loads (heater, pump, motor) for shorts to ground using megohmmeter (>1MΩ required).Verify proper grounding continuity from chassis ground lug to outlet ground terminal (

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

Recommended part

Recommended part for this error code

No replacement part recommended for this code

The researched guidance for Samsung Washer error 8E points to user-action and diagnostic steps above rather than a mapped replacement part. We will not invent a part or send you to an unrelated product.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Samsung Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.