Skip to main content
Appliance Fix Guide

Samsung Washer error code

Samsung Washer Error 4E1

Verify cold water hose connected to cold inlet valve (common installation error).

Verify cold water hose connected to cold inlet valve (common installation error).

UnknownStart with 5-15 minutes of safe checks
✅ WORTH FIXINGParts under $100
Samsung washer repair guide for error 4E1
Error code4E1Washer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Verify cold water hose connected to cold inlet

    Verify cold water hose connected to cold inlet valve (common installation error).

  2. 2
    Disconnect power and access thermistor at bottom front

    Disconnect power and access thermistor at bottom front of tub (behind lower panel).

  3. 3
    Disconnect connector and measure resistance across thermistor terminals

    Disconnect connector and measure resistance across thermistor terminals at room temperature (70°F/21°C = ~12kΩ).

A quick explanation

What does 4E1 mean?

Verify cold water hose connected to cold inlet valve (common installation error).

The answer you came for

How to fix Samsung washer error 4E1

Start with the safest checks and work from simple to technical.

  1. 1

    Verify cold water hose connected to cold inlet

    Verify cold water hose connected to cold inlet valve (common installation error).

  2. 2

    Disconnect power and access thermistor at bottom front

    Disconnect power and access thermistor at bottom front of tub (behind lower panel).

  3. 3

    Disconnect connector and measure resistance across thermistor terminals

    Disconnect connector and measure resistance across thermistor terminals at room temperature (70°F/21°C = ~12kΩ).

  4. 4

    Submerge thermistor tip in ice water - resistance

    Submerge thermistor tip in ice water - resistance should increase to 30-40kΩ within 30 seconds.

  5. 5

    Replace thermistor DC34-00024A if readings OL (open) or

    Replace thermistor DC34-00024A if readings OL (open) or 0Ω (short) or unstable.

  6. 6

    Inspect wiring harness for rodent damage or pinched

    Inspect wiring harness for rodent damage or pinched wires near tub mounting points.

  7. 7

    Check connector J3 on main PCB for corrosion

    Check connector J3 on main PCB for corrosion - clean with electrical contact cleaner if present.

  8. 8

    Restart the washer and confirm the 4E1 message

    Restart the washer and confirm the 4E1 message returns under the same condition instead of after a one-time interruption.

  9. 9

    Check the simple causes first

    Check the simple causes first: load balance, water supply, drain flow, door or lid closure, visible leaks, and power stability.

  10. 10

    Inspect accessible wiring connectors and moisture-prone areas before

    Inspect accessible wiring connectors and moisture-prone areas before assuming the control board has failed.

  11. 11

    Use the complete Samsung washer model number from

    Use the complete Samsung washer model number from the door, lid, or rear tag before matching any pump, valve, sensor, suspension, lock, or board category.

  12. 12

    If the 4E1 code points to a specific

    If the 4E1 code points to a specific system, test that system directly before ordering replacement parts.

Read the additional checks from the current guide

How to Fix 4E1 Error Verify cold water hose connected to cold inlet valve (common installation error).Disconnect power and access thermistor at bottom front of tub (behind lower panel).Disconnect connector and measure resistance across thermistor terminals at room temperature (70°F/21°C = ~12kΩ).Submerge thermistor tip in ice water - resistance should increase to 30-40kΩ within 30 seconds.Replace thermistor DC34-00024A if readings OL (open) or 0Ω (short) or unstable.Inspect wiring harness for rodent damage or pinched wires near tub mounting points.Check connector J3 on main PCB for corrosion - clean with electrical contact cleaner if present. Samsung Washer 4E1 Checks Before Replacing Parts Restart the washer and confirm the 4E1 message returns under the same condition instead of after a one-time interruption. Check the simple causes first: load balance, water supply, drain flow, door or lid closure, visible leaks, and power stability. Inspect accessible wiring connectors and moisture-prone areas before assuming the control board has failed. Use the complete Samsung washer model number from the door, lid, or rear tag before matching any pump, valve, sensor, suspension, lock, or board category. If the 4E1 code points to a specific system, test that system directly before ordering replacement parts. Recommended Parts to Check Samsung washer parts for 4E1 error Estimated part range: $25-$180 Confirm compatibility with your full Samsung washer model number before ordering. Check Price & Availability ->

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

Recommended part

Recommended part for this error code

No replacement part recommended for this code

The researched guidance for Samsung Washer error 4E1 points to user-action and diagnostic steps above rather than a mapped replacement part. We will not invent a part or send you to an unrelated product.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Samsung Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.