Skip to main content
Appliance Fix Guide

Electrolux Washer error code

Electrolux Washer Error LO

Low water pressure.

Low water pressure.

EasyStart with 5-15 minutes of safe checks
Diagnose before buying a part
Electrolux washer repair guide for error LO
Error codeLOWasher

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Locate the hot and cold water supply valves

    Locate the hot and cold water supply valves behind the washer and confirm they are turned all the way on.

  2. 2
    Turn off the water supply valves and unplug

    Turn off the water supply valves and unplug the washer from the outlet.

  3. 3
    Unscrew the water inlet hoses from the back

    Unscrew the water inlet hoses from the back of the washing machine. Have a small bucket or towel ready for any water still in the hoses.

A quick explanation

What does LO mean?

Low water pressure.

The answer you came for

How to fix Electrolux washer error LO

Start with the safest checks and work from simple to technical.

  1. 1

    Locate the hot and cold water supply valves

    Locate the hot and cold water supply valves behind the washer and confirm they are turned all the way on.

  2. 2

    Turn off the water supply valves and unplug

    Turn off the water supply valves and unplug the washer from the outlet.

  3. 3

    Unscrew the water inlet hoses from the back

    Unscrew the water inlet hoses from the back of the washing machine. Have a small bucket or towel ready for any water still in the hoses.

  4. 4

    Look inside the two water inlet ports on

    Look inside the two water inlet ports on the washer. You will see small filter screens.

  5. 5

    Carefully remove these screens using needle-nose pliers and

    Carefully remove these screens using needle-nose pliers and clean them thoroughly under a faucet to remove any sediment or debris. A small brush can help dislodge stubborn particles.

  6. 6

    Reinsert the clean filter screens, reattach the water

    Reinsert the clean filter screens, reattach the water hoses securely, and turn the water supply back on fully before plugging the washer in again.

  7. 7

    Turn the appliance off, wait about 2 minutes,

    Turn the appliance off, wait about 2 minutes, then turn it back on.

Read the additional checks from the current guide

How to Fix LO Error (Step-by-Step) Locate the hot and cold water supply valves behind the washer and confirm they are turned all the way on. Turn off the water supply valves and unplug the washer from the outlet. Unscrew the water inlet hoses from the back of the washing machine. Have a small bucket or towel ready for any water still in the hoses. Look inside the two water inlet ports on the washer. You will see small filter screens. Carefully remove these screens using needle-nose pliers and clean them thoroughly under a faucet to remove any sediment or debris. A small brush can help dislodge stubborn particles. Reinsert the clean filter screens, reattach the water hoses securely, and turn the water supply back on fully before plugging the washer in again. Turn the appliance off, wait about 2 minutes, then turn it back on.

What to Check Next on This Electrolux Washer Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux washer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux washer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. Still Not Working? If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure. Browse all Electrolux error codes: Electrolux Error Codes

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

Recommended part

Recommended part for this error code

Part listed in the current guide

OEM candidate: 137353500

Why this part is shown: It is associated with Electrolux Washer error LO in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete washer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Electrolux Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.