Category: Samsung

How to Fix Samsung Dryer Error C80
Problem: Vent is approximately 80% clogged

How to Fix C80 Error
1. This is a critical safety warning, not a fault with the dryer. It means the ‘Vent Blockage Test’ has determined your exhaust vent is approximately 80% clogged.
2. UNPLUG THE DRYER. A clogged vent is a serious fire hazard.
3. Clean the lint filter inside the dryer door.
4. Disconnect the vent hose from the back of the dryer and clean it out thoroughly. Use a vent cleaning kit (brush and flexible rods) to clean the entire length of the duct in your wall, all the way to the exterior of your house. Ensure the outside flap moves freely.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error C90
Problem: Vent is over 90% clogged

How to Fix C90 Error
1. This is a critical safety warning, not a fault with the dryer. It means the ‘Vent Blockage Test’ has determined your exhaust vent is over 90% clogged.
2. UNPLUG THE DRYER IMMEDIATELY. Do not use the dryer until the vent is cleaned. A clogged vent is a serious fire hazard.
3. Clean the lint filter inside the dryer door.
4. Disconnect the vent hose from the back of the dryer and clean it out thoroughly. Use a vent cleaning kit (brush and flexible rods) to clean the entire length of the duct in your wall, all the way to the exterior of your house. Ensure the outside flap moves freely.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error HC4
Problem: Overheating error

How to Fix HC4 Error
1. UNPLUG THE DRYER. This is a critical over-temperature fault. The number one cause is a clogged vent.
2. THOROUGHLY CLEAN THE ENTIRE VENT SYSTEM, from the lint screen to the outside of the house. This is mandatory.
3. After cleaning the vent, you must replace the safety thermostat that tripped. Remove the rear panel to access the heater assembly.
4. Locate the high-limit thermostat and the one-time thermal fuse on the heater can. Use a multimeter to test both for continuity. The one that is open (no continuity) is the one that blew.
5. Replace the blown thermostat/fuse. NEVER bypass a safety thermostat.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error bC2
Problem: Button stuck on control panel

How to Fix bC2 Error
1. UNPLUG THE DRYER. This error means a button on the user interface (UI) is stuck.
2. First, try gently pressing and wiggling each button on the control panel to see if you can free the stuck one. Sometimes wiping the panel with a damp cloth can help.
3. If that doesn’t work, the UI board is faulty and needs to be replaced. Access the board by removing the top control console panel.
4. Disconnect the ribbon cable(s) and any other wire harnesses from the old UI board. Remove its mounting screws, install the new board, and reconnect everything.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error bE2
Problem: Button stuck on control panel

How to Fix bE2 Error
1. UNPLUG THE DRYER. This is an alias for bC2, indicating a stuck button on the control panel.
2. Try to free the stuck button by gently pressing and releasing all buttons on the panel.
3. If the error persists, the user interface board has failed. Remove the control console to access the board.
4. Disconnect all wiring from the old board, remove it, and install the new one. Reconnect the wiring and reassemble the console.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error d0
Problem: Door error

How to Fix d0 Error
1. This is an alias for the ‘dF’ door error. First, open the dryer door and close it again firmly.
2. Check for any lint, clothing, or other items that might be caught in the latch, preventing it from closing completely.
3. If the door is clear and closes properly but the error persists, the door latch/switch assembly has failed. UNPLUG THE DRYER.
4. Access the switch by removing the top or front panel. Disconnect the wiring, remove the old switch, and install the new one.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error dF
Problem: Door circuit failure

How to Fix dF Error
1. This error indicates a ‘Door Failure’ or problem with the door circuit. First, open the dryer door and close it again firmly.
2. Check for any lint, clothing, or other items that might be caught in the latch, preventing it from closing completely.
3. If the door is clear and closes properly but the error persists, the door latch/switch assembly has failed. UNPLUG THE DRYER.
4. Access the switch by removing the top or front panel. Disconnect the wiring, remove the old switch, and install the new one.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Dryer Error tE3
Problem: Temperature sensor fault

How to Fix tE3 Error
1. UNPLUG THE DRYER. This is a variant of the ‘tE’ temperature sensor error.
2. The thermistor is usually located on the blower housing or the heater assembly. Remove the dryer’s front or rear panel to access it.
3. Disconnect the wire harness from the thermistor and test its resistance with a multimeter.
4. A functional thermistor should read around 10,000 ohms (10kΩ) at room temperature. If the reading is incorrect, it has failed.
5. Replace the faulty thermistor, reconnect the wiring, and reinstall the panel.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You

Browse all Samsung error codes: Samsung Error Codes
March 13, 2026
How to Fix Samsung Washer Error 0C
Problem: Water overflow — tub level too high

How to Fix 0C Error
1. This is an ‘Overflow’ error. It means the water level sensor is malfunctioning and allowing the tub to fill with too much water.
2. UNPLUG THE WASHER. Access the main control area by removing the top panel of the washer.
3. Locate the water level sensor (pressure switch). It will have a thin air tube and a wire connector attached.
4. Disconnect the wiring and the air tube (check the tube for blockages or kinks). Remove the old sensor and install the new one.
5. Securely reattach the air tube and wire harness, then reassemble the washer.
Samsung Washer 0C Checks Before Replacing Parts
1. Restart the washer and confirm the 0C message returns under the same condition instead of after a one-time interruption.
2. Check the simple causes first: load balance, water supply, drain flow, door or lid closure, visible leaks, and power stability.
3. Inspect accessible wiring connectors and moisture-prone areas before assuming the control board has failed.
4. Use the complete Samsung washer model number from the door, lid, or rear tag before matching any pump, valve, sensor, suspension, lock, or board category.
5. If the 0C code points to a specific system, test that system directly before ordering replacement parts.
Recommended Parts to Check

Samsung washer parts for 0C error

Estimated part range: $25-$180

Confirm compatibility with your full Samsung washer model number before ordering.

Check Price & Availability ->

Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:

For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the Samsung washer 0C error returns after the basic checks, stop and recheck the full model number, the exact symptom, wiring, sensors, water or drain path, and visible component condition before buying another part.
March 12, 2026
How to Fix Samsung Washer Error 0E
Problem: Water overflow — tub level too high

How to Fix 0E Error
1. This is an ‘Overflow’ error, an alias of OC. It means the water level sensor is malfunctioning.
2. UNPLUG THE WASHER. Access the main control area by removing the top panel of the washer.
3. Locate the water level sensor (pressure switch). It will have a thin air tube and a wire connector attached.
4. Disconnect the wiring and the air tube (check the tube for blockages or kinks). Remove the old sensor and install the new one.
5. Securely reattach the air tube and wire harness, then reassemble the washer.
Samsung Washer 0E Checks Before Replacing Parts
1. Restart the washer and confirm the 0E message returns under the same condition instead of after a one-time interruption.
2. Check the simple causes first: load balance, water supply, drain flow, door or lid closure, visible leaks, and power stability.
3. Inspect accessible wiring connectors and moisture-prone areas before assuming the control board has failed.
4. Use the complete Samsung washer model number from the door, lid, or rear tag before matching any pump, valve, sensor, suspension, lock, or board category.
5. If the 0E code points to a specific system, test that system directly before ordering replacement parts.
Recommended Parts to Check

Samsung washer parts for 0E error

Estimated part range: $25-$180

Confirm compatibility with your full Samsung washer model number before ordering.

Check Price & Availability ->

Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

Ask a Technician Online – Get Answer in Minutes
Find a Local Repair Pro Near You
When It’s Better to Replace Than Repair

Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:

For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Budget Option

Top Rated Washers Under $600

Amazon’s Highest-Rated Value Models

Free ‘Room of Choice’ Delivery Available

Professional Haul-away Options at Checkout

View Top Rated Models & Delivery Options

Mid-Range Option

Top Rated Washers $600 to $1,000

Best-Sellers with Thousands of 5-Star Reviews

Expert Installation & Hookup Services available

Protection Plans for Long-Term Peace of Mind

View Top Rated Models & Delivery Options

Premium Option

Top Rated Washers Over $1,000

Top-of-the-Line Performance & Technology

White-Glove Delivery and Haul-away eligible

Comprehensive Warranty & Support Options

View Top Rated Models & Delivery Options
Why Upgrade via Amazon?

Fast, Scheduled Delivery – You pick the date and time

Expert Installation – Professional setup available for most models

Old Appliance Haul-away – They’ll take your broken unit when they leave

Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the Samsung washer 0E error returns after the basic checks, stop and recheck the full model number, the exact symptom, wiring, sensors, water or drain path, and visible component condition before buying another part.
March 12, 2026