Category: Maytag

  • How to Fix Maytag Refrigerator Error F6

    How to Fix Maytag Refrigerator Error F6

    Problem: User interface board communication fault – display board not responding to main control commands

    How to Fix Refrigerator Error

    1. Unplug refrigerator.
    2. Remove display panel bezel (typically snaps off with flat blade screwdriver).
    3. Disconnect UI board harness from main board.
    4. Inspect connectors for corrosion/bent pins – clean with contact cleaner.
    5. Test UI board power input: should read 12-14VDC at J1 connector with unit powered.
    6. Press buttons while monitoring voltage fluctuations at communication pins – no change indicates dead UI board.
    7. Replace user interface board WPW10366217 if unresponsive.
    8. If new UI board fails to initialize, suspect main control board W10868991 communication circuit failure – replace main board and reprogram.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error F7

    How to Fix Maytag Refrigerator Error F7

    Problem: Condenser fan motor fault – fan not running during compressor operation causing high head pressure

    How to Fix Refrigerator Error

    1. Pull refrigerator forward and unplug.
    2. Remove lower rear access panel.
    3. Locate condenser fan motor adjacent to compressor.
    4. Spin fan blade manually – should rotate freely without grinding.
    5. Disconnect motor harness and test resistance: 50-150Ω indicates good motor.
    6. Apply 120VAC directly to motor terminals (use fused jumper wires) – motor should run immediately.
    7. If motor doesn’t run with direct power, replace condenser fan motor WPW
    8. Clean condenser coils thoroughly before reinstalling panel – restricted airflow accelerates fan failure.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error F8

    How to Fix Maytag Refrigerator Error F8

    Problem: Evaporator fan motor fault – fan not running causing no airflow over evaporator coils

    How to Fix Refrigerator Error

    1. Unplug refrigerator.
    2. Remove freezer rear interior panel to access evaporator assembly.
    3. Inspect fan blade for ice obstruction – defrost completely if frozen.
    4. Spin fan blade manually – should rotate freely without bearing noise.
    5. Disconnect motor harness and test resistance: 50-200Ω indicates good motor.
    6. Apply 12-14VDC directly to motor terminals – should run immediately.
    7. If motor seized or no response to direct power, replace evaporator fan motor WPW
    8. Check for water dripping onto motor from defrost drain – repair drain clog to prevent repeat failure.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error F9

    How to Fix Maytag Refrigerator Error F9

    Problem: Defrost system fault – defrost cycle not terminating properly indicating failed defrost thermostat or heater

    How to Fix Refrigerator Error

    1. Initiate forced defrost via service mode: Press Door Alarm + Freezer Down 3 sec, then press Freezer Up until ‘dF’ displays.
    2. Monitor evaporator coils – should begin defrosting within 2 minutes (water dripping into drain pan).
    3. After 25 minutes, defrost should terminate automatically. If not terminating:
    4. Unplug unit and access evaporator compartment.
    5. Locate defrost thermostat clipped to evaporator tubing – test continuity: should OPEN above 45°F. If stays closed, replace thermostat WPW
    6. Test defrost heater continuity: should read 20-50Ω. Open heater requires replacement.
    7. If both components test good, main control board W10868991 has failed defrost timer circuit – replace board.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error FL

    How to Fix Maytag Refrigerator Error FL

    Problem: Water filter reminder – not an error but maintenance indicator (some models display as fault)

    How to Fix Refrigerator Error

    1. Press and hold Water Filter Reset button for 3 seconds until indicator light turns off.
    2. If no reset button: press and hold Ice Type and Dispenser Lock buttons simultaneously for 3 seconds.
    3. If indicator won’t reset: unplug refrigerator for 5 minutes to reset control memory.
    4. Verify correct filter model installed (e.g., UKF8001AXX) – incompatible filters trigger persistent reminders.
    5. Replace water filter every 6 months regardless of indicator status to maintain water quality and prevent valve clogging.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error PO

    How to Fix Maytag Refrigerator Error PO

    Problem: Power outage detected – freezer temperature exceeded 18°F during power interruption

    How to Fix Refrigerator Error

    1. Press any temperature control button to clear PO indicator.
    2. Verify food safety: if PO displayed >4 hours, discard perishables in refrigerator compartment. Freezer items safe if still frozen solid.
    3. No repair needed – PO is informational only.
    4. To prevent future PO events during brief outages: install UPS backup power system rated for refrigerator surge current (minimum 1500VA).

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error LED Flash Code 9

    How to Fix Maytag Refrigerator Error LED Flash Code 9

    Problem: Service mode diagnostic: 9 flashes = defrost system fault (matches F9)

    How to Fix Refrigerator Error

    1. Enter service mode and confirm 9-flash pattern.
    2. Perform forced defrost test #101 to verify heater/thermostat operation.
    3. Replace defrost thermostat WPW10316428 or heater as needed.
    4. If components test good, replace main control board W
    5. Clear fault history via test #25 after successful defrost cycle completion.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error 8.8.8

    How to Fix Maytag Refrigerator Error 8.8.8

    Problem: Critical control board failure – EEPROM corruption or hardware fault preventing normal operation

    How to Fix Refrigerator Error

    1. Unplug refrigerator for 15 minutes – if
    2. 8 returns immediately on power-up, board is defective.
    3. Remove rear access panel and inspect main control board W10868991 for visible damage (burnt components, swollen capacitors).
    4. Check all harness connections – especially J1 power input – for loose/corroded pins.
    5. Verify proper household voltage (110-125VAC) at outlet.
    6. If board shows no physical damage but
    7. 8 persists, EEPROM has failed – replace main control board with exact OEM match.
    8. AFTER replacement: MUST enter programming mode and input correct 4-digit code from serial plate sticker. Failure to program correctly causes permanent lockout.
    9. Note:
    10. 8 often appears after power surge – install whole-house surge protector to prevent recurrence.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Refrigerator Error PE H2O

    How to Fix Maytag Refrigerator Error PE H2O

    Problem: Water system configuration error – control board detecting incompatible water valve or filter system

    How to Fix Refrigerator Error

    1. Enter programming mode and navigate to water system configuration (typically code position
    2. .
    3. Verify setting matches installed system: 0=no water, 1=standard valve, 2=electronic valve.
    4. Adjust setting if incorrect and save properly.
    5. If PE H2O persists: inspect water valve harness for short circuit – disconnect valve and test resistance (should read 150-300Ω).
    6. Test water filter presence switch continuity – should close when filter installed.
    7. If all components test good, main control board W10868991 has failed water valve driver – replace board and reprogram.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes

  • How to Fix Maytag Dryer Error F01

    How to Fix Maytag Dryer Error F01

    Problem: Main electronic control board failure or motor control circuit error

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker for safety.
    2. Remove rear panel to access control board.
    3. Inspect board for burnt components, bulging capacitors, or scorch marks.
    4. Check motor wiring harness for damage or loose connections at both motor and board.
    5. Test motor windings with multimeter (should read 2-6 ohms between terminals).
    6. If motor tests good and wiring intact, replace main control board WPW
    7. Reconnect all harnesses securely before reassembly.
    8. Restore power and run diagnostic cycle to verify repair.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.



    Browse all Maytag error codes: Maytag Error Codes