Category: Kenmore

  • How to Fix Kenmore Dryer Error FF

    How to Fix Kenmore Dryer Error FF

    Problem: Fan failure – blower wheel not rotating

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Inspect blower wheel for debris, damage, or obstructions.
    4. Check blower wheel mounting and shaft for proper alignment.
    5. Test motor operation independently of blower wheel.
    6. If motor runs but blower wheel doesn’t turn, inspect drive belt for damage.
    7. Remove mounting screws securing blower housing.
    8. Replace damaged blower wheel assembly or drive belt as needed.
    9. Reassemble components and verify proper alignment.
    10. Test airflow and drying performance after repairs.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F8E1

    How to Fix Kenmore Washer Error F8E1

    Problem: Water supply error – no water detected during fill

    How to Fix Washer Error

    1. Turn off power and check household water supply valves.
    2. Verify water pressure at supply lines (minimum 20 PSI required).
    3. Remove lower front access panel.
    4. Inspect water inlet valve screens for debris or mineral buildup.
    5. Clean inlet valve filter screens with vinegar solution.
    6. Test inlet valve solenoids with multimeter for proper resistance.
    7. If valve is faulty, disconnect water supply lines and electrical connector.
    8. Remove mounting screws and replace water inlet valve assembly.
    9. Restore water and power connections.
    10. Test fill cycle operation and timing.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error PC

    How to Fix Kenmore Dryer Error PC

    Problem: Power cord failure – damaged wiring

    How to Fix Dryer Error

    1. Turn off power at circuit breaker.
    2. Remove rear access panel.
    3. Inspect power cord for visible damage, fraying, or burns.
    4. Disconnect power cord from terminal block inside dryer.
    5. Test each conductor for continuity with multimeter.
    6. Check terminal block connections for corrosion or loose terminals.
    7. If power cord is damaged, remove mounting screws securing cord strain relief.
    8. Install new power cord assembly with proper strain relief.
    9. Connect wires to terminal block following color coding (black-red-white-green).
    10. Restore power and test dryer operation with voltage verification.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F7E1

    How to Fix Kenmore Washer Error F7E1

    Problem: Motor control system failure during operation

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove front access panel and motor control board cover.
    3. Inspect motor control board for burnt components or damaged traces.
    4. Check motor wiring harness for damage or loose connections.
    5. Test motor windings for proper resistance readings.
    6. Inspect motor brushes for wear (if applicable).
    7. If motor control board is faulty, document wire connections.
    8. Remove mounting screws and disconnect all connectors.
    9. Install new motor control board assembly.
    10. Test motor operation at various speeds and loads.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F6E3

    How to Fix Kenmore Washer Error F6E3

    Problem: Communication failure between user interface and main control

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove control panel faceplate and access cover.
    3. Inspect ribbon cable connections between boards.
    4. Check for damaged connectors or bent pins. . Test communication signals with multimeter if possible.
    5. Clean all electrical contacts with contact cleaner.
    6. If connections are good but error persists, replace user interface board.
    7. Document all wire connections before disconnecting.
    8. Install new user interface board assembly.
    9. Test all button functions and display operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F6E2

    How to Fix Kenmore Washer Error F6E2

    Problem: Communication error between control boards

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel and main access covers.
    3. Inspect all communication wire harnesses between boards.
    4. Check for damaged, corroded, or loose connectors.
    5. Test communication lines for continuity and proper voltage.
    6. Clean all electrical contacts with contact cleaner.
    7. If wiring is good, suspect control board failure.
    8. Document all wire connections before disconnecting boards.
    9. Replace faulty control board assembly.
    10. Reconnect all harnesses and run diagnostic communication tests.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F5E2

    How to Fix Kenmore Washer Error F5E2

    Problem: Door will not lock – mechanical or electrical failure

    How to Fix Washer Error

    1. Turn off power supply.
    2. Open washer door fully.
    3. Inspect door lock mechanism for debris or physical damage.
    4. Check door strike plate alignment and condition.
    5. Test door lock solenoid resistance with multimeter.
    6. Inspect wiring harness for damage or corrosion.
    7. Check door latch mechanism for proper engagement.
    8. If lock assembly is faulty, disconnect electrical connector.
    9. Remove mounting screws and replace door lock assembly.
    10. Test door lock function multiple times to verify reliability.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F5E1

    How to Fix Kenmore Washer Error F5E1

    Problem: Lid switch error – lid open during cycle

    How to Fix Washer Error

    1. Turn off power supply.
    2. Open washer lid fully.
    3. Inspect lid switch mechanism for proper alignment.
    4. Test lid switch continuity with multimeter (should change state when lid closes).
    5. Check lid strike plate alignment with switch mechanism.
    6. Inspect lid switch wiring for damage or loose connections.
    7. If lid switch is faulty, disconnect electrical connector.
    8. Remove mounting screws and replace lid switch assembly.
    9. Ensure proper alignment during installation.
    10. Test lid closure and switch operation during spin cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F3E2

    How to Fix Kenmore Washer Error F3E2

    Problem: Temperature sensor short circuit during operation

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove lower front access panel.
    3. Locate temperature sensor on tub or heater assembly.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter (should not read zero ohms).
    6. Inspect sensor wiring for damage or pinching.
    7. If sensor is shorted, remove mounting screw and replace sensor.
    8. Check wiring harness for short circuits to ground.
    9. Clean sensor mounting area and ensure proper sealing.
    10. Reconnect electrical connector and test temperature readings during cycle.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F0E4

    How to Fix Kenmore Washer Error F0E4

    Problem: High water temperature detected – safety shutdown

    How to Fix Washer Error

    1. Turn off power supply immediately.
    2. Allow washer to cool for 30 minutes.
    3. Check household water heater temperature settings (should not exceed 120°F).
    4. Inspect temperature sensor for proper operation.
    5. Test heating element for short circuits or grounding issues.
    6. Check thermostat operation and calibration.
    7. Verify proper water inlet valve mixing function.
    8. Test temperature readings with external thermometer during fill cycle.
    9. If temperature sensor is faulty, replace sensor assembly.
    10. Run diagnostic cycle to verify proper temperature control.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.